remote control MERCEDES-BENZ SLR CLASS 2005 User Guide

219 Controls in detail
Useful features
Step 9:
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the
following step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (2, 3
or4).
Step 11:

Press, hold for two seconds and
release same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.Step 12:

Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Continue to press and hold the
integrated signal transmitter button
(2, 3 or4) while you press and
re-press (“cycle”) your hand-held
remote control transmitter6 every
two seconds until the frequency signal
has been learned. Upon successful
training, the indicator lamp1 will
flash slowly and then rapidly after
several seconds.

Proceed with programming step 5 and
step 6 to complete.

220 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 40).

Select and press the appropriate
integrated signal transmitter button
(2, 3 or4) to activate the remote
controlled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory

Switch on the ignition (
page 40).

Simultaneously hold down the signal
transmitter buttons2 and 4, for
approximately 20 seconds, until the
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp will begin to flash
after 20 seconds. Without releasing
the integrated signal transmitter
button, proceed with programming
starting with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

400 IndexI
Identification labels
Emission control information
label 366
Vacuum line routing diagram
label 366
Ignition 40
Immobilizer 90
Activating 90
Deactivating 90
Infant and child restraint systems 72
Installing 77
Installing
Infant and child restraint systems 77
Towing eye bolt 359
Wiper blades 348Instrument cluster 28, 113, 387
Coolant temperature gauge 114
Illumination 113
Multifunction display 117
Outside temperature indicator 115
Select language 130
Instrument lighting 113
Interior lighting 33, 111
Automatic control 111
Delayed shut-off 134
Delayed switch-off 134
Manual operation 112
Interior rear view mirror
Adjusting 43
Interior storage spaces 200J
Jump starting 354
K
Key, SmartKey
Battery check lamp 98
Factory setting 98
Loss of 100
Opening 38
Positions in starter switch 40
Remote control 96
Replacing the battery 344
Turning off the engine 58
Kickdown 173, 387
Kilometers/miles in speedometer 129
Kilopascal 279
Knee airbags 68

405 Index
Q
Quick search
Phone book 141
R
Radio
Selecting stations 123
Station search 123
Station selection setting 135
Radio operation 149
Radio see Radio operation
Radio transmitters, control and
operation 237
Range (distance to empty)
Calling up 138
Reactivating
Automatic climate control 191
Reading lamp 33
Rear
Storage compartment 201
Rear bulbs 347Rear fog lamp
Switching on 109
Rear lamps see Tail lamps
Rear view mirrors see Mirrors
Rear window defroster 181
Rear-view mirror 33
Recommended inflation pressure 280
Redial memory 142
Refueling 240
Refuelling
Unleaded premium grade
gasoline 240
Regular checks 241
Remote control
SmartKey 96
Removing
Anti-theft wheel nuts 283
Replacing
Battery (SmartKey) 344
Wiper blades 348Resetting
All functions (control system) 126
ESP 307
Fuel consumption 138
Maintenance service indicator 288
Trip odometer 115
Residual heat utilization 190
Restraint system see Infant and child re-
straint systems
Restraint systems 62
Airbags 62, 63
Child seat recognition 62
Child seats 62
Emergency Tensioning Device
(ETD) 62, 72
Seat belts 62, 69
Rim 280
RON 240, 388
Roof rack 225