lock MERCEDES-BENZ SLR CLASS 2007 User Guide

41 Getting started
Adjusting
Adjusting
Seats
Warning!G
All seat, steering wheel, and rear view mirror
adjustments, as well as fastening of seat
belts, must be done before the vehicle is put
into motion.
Warning!G
Do not adjust the driver’s seat while driving.
Adjusting the seat while driving could cause
the driver to lose control of the vehicle.
Never ride in a moving vehicle with the seat
back in an excessively reclined position as
this can be dangerous. You could slide un-
der the seat belt in a collision. If you slide
under it, the belt would apply force at the ab-
domen or neck. That could cause serious or
fatal injuries. The seat back and seat belts
provide the best restraint when the wearer
is in a nearly upright position and belts are
properly positioned on the body.
Warning!G
Your seat must be adjusted so that you can
correctly fasten your seat belt (
page 45).
Observe the following points:

Adjust the seat to a comfortable seating
position that still allows you to reach the
accelerator/brake pedal safely. The po-
s i ti on s ho ul d be as fa r t o t he r ea r a s po s -
sible, consistent with ability to properly
operate controls.

Adjust the seat until a comfortable
steering wheel position is reached with
your arms slightly bent at the elbow.

Never place hands under the seat or
near any moving parts while a seat is
being adjusted.
Failure to do so could result in an accident
and/or serious personal injury.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle.
Even with the SmartKey removed from the
starter switch or the vehicle, the seats can
be operated. Therefore, do not leave chil-
dren unattended in the vehicle, or with ac-
cess to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.

42 Getting started
Adjusting
The seat adjustment switch is located on
the door sill.
1Seat fore and aft adjustment
2Seat height
3Seat angleSeat fore and aft adjustment
Slide the switch forwards or backwards
in the direction of arrow 1.
Seat height
Slide the switch up or down in the
direction of arrow 2.
Seat angle
Slide the switch up or down in the
direction of arrow 3.
Steering wheel
!When moving the seat, make sure that there
are no items in the footwell or behind the seat.
Otherwise you could damage the seat.
Warning!G
Do not adjust the steering wheel while
driving. Adjusting the steering wheel while
driving could cause the driver to lose control
of the vehicle.
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle.
Even with the SmartKey removed from the
starter switch or the vehicle, the steering
wheel can be adjusted. Therefore, do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.

48 Getting started
Driving
Gearshift pattern
P Park position with gear selector lever
lock
R Reverse gear
N Neutral
D Drive position
For more information, see “Automatic
transmission” (
page 169).1Cover
2Start button
Make sure the gear selector lever is set
to park positionP.
Do not depress the accelerator.
Switch on the ignition (page 40).
Lift up cover1.
Press start button2 once.
The engine starts.
Close cover1.For information on turning off the engine,
see “Turning off the engine” (
page 56).
Warning!G
Make sure the cover of the start button is
closed after starting the engine. Otherwise
you could be injured on the open cover in an
accident or during driving maneuvers.

49 Getting started
Driving
Starting difficulties
If the engine does not start as described,
carry out the following steps:
Turn the SmartKey in the starter switch
to position0 and repeat starting
procedure (
page 48).
Remember that extended starting
attempts can drain the battery.
If the engine does not start after several
starting attempts, there could be a
malfunction in the engine electronics or in
the fuel supply system.
Notify an authorized Mercedes-Benz
Center.
Parking brake
1Release button
2Parking brake leverPull lever2 upwards slightly, press
release button1 and move the lever
down to the stop.
The warning lamp; (USA only)
or3 (Canada only) in the
instrument cluster goes out.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could release the parking brake, which
could result in an accident and/or personal
serious injury.

50 Getting started
Driving
Driving off
Depress the brake pedal.
The gear selector lever lock is released.
Place the gear selector lever in drive
positionD or reverse gearR.
Release the brake pedal.
Carefully depress the accelerator
pedal.After a cold start, the transmission engag-
es at a higher revolution. This allows the
catalytic converter to reach its operating
temperature earlier.
Warning!G
It is dangerous to shift the gear selector le-
ver out of park positionP or neutralN if the
engine speed is higher than idle speed. If
your foot is not firmly on the brake pedal,
the vehicle could accelerate quickly forward
or in reverse. You could lose control of the
vehicle and hit someone or something. Only
shift into gear when the engine is idling nor-
mally and when your right foot is firmly on
the brake pedal.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.
!In order to avoid damage to the
transmission:

Wait for the gear selection process to com-
plete before setting the vehicle in motion.

Place the gear selector lever in reverse
gearR or park positionP only when the vehi-
cle is stopped.
!If you hear a warning signal and the mes-
sage
Release parking brake
appears in the multifunction display when driving
off, you have forgotten to release the parking
brake.
Release the parking brake (
page 49).
!Do not run cold engine at high engine speed.
Running a cold engine at high engine speed may
shorten the service life of the engine.
!Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear.
iOnce the vehicle is in motion, the automatic
central locking system engages.
You can deactivate the automatic locking using
the control system (
page 139).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.

52 Getting started
Driving
Windshield wipers
The combination switch is located on the
left of the steering column.
Combination switch
1Single wipe
Wiping with windshield washer fluid
2Switching on windshield wipers
Switch on the ignition (page 40).Switching on windshield wipers
Turn the combination switch in direc-
tion of arrow 2 to the desired position,
depending on the intensity of the rain.
0Windshield wipers off
IIntermittent wiping
IINormal wiper speed
IIIFast wiper speed
iTo signal minor directional changes, such as
changing lanes, press combination switch to
point of resistance only and release. The corre-
sponding turn signals will flash three times.!Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
wipers in dry weather conditions, always operate
the windshield wipers with windshield washer
fluid (
page 53).
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off
immediately.

For safety reasons, stop the vehicle in a safe
location, remove the SmartKey from starter
switch before attempting to remove any
blockage.

The hood must be opened (page 250) be-
fore folding the wiper arms away from the
windshield. You could otherwise damage the
hood and/or the wiper arm.

Remove the blockage.

Turn the windshield wipers on again.If windshield wipers fail to function at all in
switch positionI,

set the combination switch to the next
highest wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center

55 Getting started
Parking and locking
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.Parking brake
1Parking brake lever
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
system. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle.
Warning!G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury or dam-
age to the vehicle drivetrain as a result of ve-
hicle movement, before turning off the
engine and leaving the vehicle always:

Keep right foot on brake pedal.

Pull the parking brake lever up as many
notches as possible.

Move the gear selector lever to park
positionP.

Slowly release brake pedal.

When parked on an incline, turn front
wheels towards the road curb.

Turn the SmartKey in the starter switch
to position0 and remove.

Take the SmartKey with you and lock
vehicle when leaving.
Warning!G
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to
lock up. You could lose control of the vehicle
and cause an accident. In addition, the
vehicle’s brake lights do not light up when
the parking brake is engaged.

56 Getting started
Parking and locking
Pull parking brake lever1 up a s m a ny
notches as possible.
When the engine is running, the
warning lamp; (USA only)
or3(Canada only) in the
instrument cluster comes on.
Switching off headlamps
Turn the exterior lamp switch
toM(
page 51).
For more information on headlamps, see
“Lighting” (
page 106).
Turning off the engine
Place the gear selector lever in
positionP.
Turn the SmartKey in the starter switch
to position0 and remove the SmartKey
from the starter switch.
The immobilizer is activated.
Releasing seat belts
Press the seat belt release button
(
page 46).
Allow the retractor to completely
rewind the seat belt by guiding the
latch plate.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children
could release the parking brake and/or
move the gear selector lever from park
positionP, either of which could result in an
accident and/or serious personal injury.
Warning!G
Getting out of your vehicle with the gear se-
lector lever not fully engaged in park
positionP is dangerous. Also, when parked
on an incline, park positionP alone may not
prevent your vehicle from moving, possibly
hitting people or objects.
Always set the parking brake in addition to
shifting to park positionP (
page 48).
When parked on an incline, turn front wheels
towards the road curb.
iAlways set the parking brake in addition to
shifting automatic transmission to park
positionP.
When parked on an incline, turn front wheels
towards the road curb.
iThe SmartKey can only be removed from the
starter switch with the gear selector lever in park
positionP.

57 Getting started
Parking and locking
Locking
Exit the vehicle and close all doors.
Press the lock button‹ on the
SmartKey (
page 38).
With the hood, trunk and all doors
closed, all turn signal lamps flash three
times. The anti-theft alarm system is
armed.
For more information, see “Locking and
unlocking” (
page 98).
!Make sure the seat belt retracts fully so that
the seat belt and/or latch plate cannot get
caught or pinched in the door or in the seat
mechanism. This can damage the seat belt and
impair the effectiveness of the seat belt, and/or
cause damage to the door and/or door trim
panel. Such damage is not covered by the
Mercedes-Benz Limited Warranty.
Damaged seat belts must be replaced. Contact
an authorized Mercedes-Benz Center.
Warning!G
To prevent possible personal injury, always
keep hands and fingers away from the door
openings when closing the doors. Be espe-
cially careful when small children are
around.
Before closing doors, make sure there is no
possibility of someone getting caught in a
door during closing.
Warning!G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.
Warning!G
Only Mercedes-Benz SLR McLaren
722 Edition:
Because of the carbon fiber the footwell
could be slippery when wet. Be careful when
exiting the vehicle with wet shoe soles, you
could slip on it.
iIf you hear a warning signal you have forgot-
ten to switch off the headlamps before opening
the driver’s door.
In addition the message$
Turn off lamps
appears in the multifunction display.
Switch off the headlamps.

76 Safety and Security
Occupant safety
Infant and child restraint systems
We recommend all infants and children be
properly restrained at all times while the
vehicle is in motion.
The passenger lap-shoulder belt has a
special seat belt retractor for secure
fastening of child restraints.
To fasten a child restraint follow child
restraint instructions for mounting. Then
pull the shoulder belt out completely and
let it retract. During seat belt retraction, a
ratcheting sound can be heard to indicate
that the special seat belt retractor is acti-
vated. The belt is now locked. Push down
on child restraint to take up any slack.
To deactivate, release seat belt buckle and
let seat belt retract completely.
The seat belt can again be used in the
usual manner.The use of infant or child restraints is re-
quired by law in all 50 states, the District of
Columbia, the U.S. territories, and all
Canadian provinces.
Infants and small children should be
seated in an appropriate infant or child
restraint system and properly secured in
accordance with the manufacturer’s in-
structions for the child restraint that com-
plies with U.S. Federal Motor Vehicle
Safety Standards 213 and 225 and
Canadian Motor Vehicle Safety Standards
213 and 210.2.
A statement by the child restraint manu-
facturer of compliance with these stan-
dards can be found on the instruction label
on the restraint and in the instruction
manual provided with the restraint.When using any infant, or toddler restraint,
or booster seat, be sure to carefully read
and follow all manufacturer’s instructions
for installation and use.
Please read and observe warning labels
affixed to inside of the vehicle and to infant
or child restraints.
The infant or child restraint are applicable
only to the standard passenger seat. Any
individualization of this seat may restrict
correct fitment of the infant or child
restraint.
Warning!G
Never release the seat belt buckle while the
vehicle is in motion, since the special seat
belt retractor will be deactivated.
Warning!G
Children 12 years old and under must be
seated and properly secured in an appropri-
ate infant or child restraint recommended
for the size and weight of the child.
The infant or child restraint must be properly
secured with the vehicle’s seat belt fully
in accordance with the child seat
manufacturer’s instructions.