light MERCEDES-BENZ SLR CLASS 2007 Owner's Manual

108 Controls in detail
Lighting
Daytime running lamp mode
Turn the exterior lamp switch to
positionM orU.
When the engine is running, the low
beam headlamps are switched on.
In low ambient light conditions, the
following lamps will switch on
additionally:

Tail and parking lamps

License plate lamps

Side marker lamps
For nighttime driving you should turn the
exterior lamp switch to positionB to
permit activation of the high beam head-
lamps.Canada only:
The daytime running lamp mode is manda-
tory and therefore in a constant mode.
When the engine is running, and you shift
from a driving position to neutralN or park
positionP, the low beam headlamps will
switch off with a three-minute delay.When the engine is running, and you

turn the exterior lamp switch to
positionC, the parking lamps and
side marker switch on additionally.

turn the exterior lamp switch to
positionB, the manual headlamp
mode has priority over the daytime
running lamp mode.
The corresponding exterior lamps
switch on (
page 106).
iWith the daytime running lamp mode activat-
ed and the exterior lamp switch in positionM
you can not switch on the high beam headlamps.
iWith the exterior lamp switch in
positionM or U you can not switch on the
high beam headlamps.
The high beam flasher is available at all times.
For nighttime driving turn the exterior lamp
switch to positionB to permit activation of
the high beam headlamps.

109 Controls in detail
Lighting
USA only:
By default, the daytime running lamp mode
is deactivated. Activate the daytime
running lamp mode using the control
system, see “Setting daytime running lamp
mode (USA only)” (
page 135).
When the engine is running, and you turn
the exterior lamp switch to positionC
orB, the manual headlamp mode has
priority over the daytime running lamp
mode.
The corresponding exterior lamps switch
on (
page 106).
Locator lighting and night security
illumination
The locator lighting and the night security
illumination are described in the “Control
system” section, see “Setting locator light-
ing” (
page 135) and “Setting night secu-
rity illumination” (
page 136).Fog lampsFront fog lamps
Switch on the low beam headlamps
(
page 106).
Pull out the exterior lamp switch to first
stop.
The front fog lamps switch on.
The green indicator lamp‡ in the
exterior lamp switch comes on.
Push in the exterior lamp switch.
The front fog lamps switch off.
The green indicator lamp‡ in the
exterior lamp switch goes out.
Warning!G
In low ambient lighting or foggy conditions,
only switch from positionU toB with
the vehicle at a standstill in a safe location.
Switching fromU toB will briefly
switch off the headlamps. Doing so while
driving in low ambient lighting conditions
may result in an accident.
iFog lamps will operate with the parking
lamps and/or the low beam headlamps on. Fog
lamps should only be used in conjunction with
low beam headlamps. Consult your State or
Province Motor Vehicle Regulations regarding al-
lowable lamp operation.
iFog lamps cannot be switched on with the
exterior lamp switch in positionU. For
switching on the fog lamps, turn the exterior
lamp switch to positionB first.

110 Controls in detail
Lighting
Rear fog lamp (driver’s side only)
Switch on the low beam headlamps
(
page 106).
Pull out the exterior lamp switch to
second stop.
The front fog lamps and rear fog lamp
switch on.
The yellow indicator lamp† in the
exterior lamp switch comes on.
Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The yellow indicator lamp† in the
exterior lamp switch goes out.
The front fog lamps remain lit.
Combination switch
The combination switch is located on the
left of the steering column.
1High beam
2High beam flasherHigh beam
USA only: Turn the exterior lamp switch
to positionB orU
(
page 106).
Canada only: Turn the exterior lamp
switch to positionB (
page 106).
Push the combination switch in
direction of arrow1 to switch on the
high beam.
The high beam headlamp indicator
lampA in the instrument cluster
comes on (
page 29).
Pull the combination switch in direction
of arrow2 to its original position to
switch off the high beam.
The high beam headlamp indicator
lampA in the instrument cluster
goes out.
High beam flasher
Pull the combination switch briefly in
direction of arrow2.

111 Controls in detail
Lighting
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter
switch.
The hazard warning flasher switches on
automatically when an air bag deploys.
The hazard warning flasher switch is
located on the upper part of the center
console.
1Hazard warning flasher switchSwitching on hazard warning flasher
Press hazard warning flasher
switch1.
All turn signals are flashing.Switching off hazard warning flasherPress hazard warning flasher switch1
again.
iWith the hazard warning flasher activated
and the combination switch set for either left or
right turn, only the respective turn signals will
operate when the ignition is switched on.
iIf the hazard warning flasher has been
activated automatically, press hazard warning
flasher switch1 once to switch it off.

112 Controls in detail
Lighting
Interior lighting
The controls are located in the overhead
control panel.
1Left-hand reading lamp on/off
2Right-hand reading lamp on/off
3Interior lighting on/off
4Automatic control on/offAutomatic control
Deactivating
Slide switch4 to the right.
The interior lighting and the entry/exit
lamps remain switched off in darkness,
even when you

unlock the vehicle

open a door

remove the SmartKey from the
starter switchActivating
Slide switch 4 to the left.
Interior lamps switches on in darkness
when you

unlock the vehicle

open a door

remove the SmartKey from the
starter switch
In addition, the entry/exit lamps in the
door come on when you open a door.
The interior lighting switches off auto-
matically following a preset time delay.
For more information, see “Setting in-
terior lighting delayed switch-off”
(
page 137).
!An interior lamp switched on manually does
not go out automatically.
Leaving an interior lamp switch in the ON posi-
tion for extended periods of time with the engine
turned off could result in a discharged battery.
iThe interior lighting is factory-set to
automatic mode.
iIf a door remains open, the interior lamps
switch off automatically after approximately
5minutes.

113 Controls in detail
Lighting
Manual control
Switching interior lighting on
Press switch3.
The interior lighting switches on.
Switching interior lighting off
Press switch3 again.
The interior lighting switches off.
Reading lamps
The reading lamps are integrated into the
interior rear view mirror.
Press reading lamp switch1or2 to
switch on the desired reading lamp.
Press reading lamp switch1or2
again to switch off the respective
reading lamp.
Courtesy lighting
For better orientation in the dark, courtesy
lamps will illuminate the interior of your
vehicle.
When you open a door:

the driver’s and passenger’s footwells
If the SmartKey is in starter switch
position1:

the center console
Trunk lamp
The trunk lamp switches on if the trunk is
opened.
If you leave the trunk open for an extended
period of time, the trunk lamp will switch
off automatically after approximately
10 minutes.
iThe center console is lit from the interior
rear view mirror.
iThe setting selected for the interior lighting
is used for the trunk lighting as well.

114 Controls in detail
Instrument cluster
For a full view illustration of the instrument
cluster, see “Instrument cluster”
(
page 28).
1Reset button
The instrument cluster is activated when
you

open a door

switch on the ignition

press the reset button1

switch on exterior lampsOpening a door will activate the instrument
cluster only for about 30 seconds.
You can change the instrument cluster
settings in the Instrument cluster submenu
of the control system (
page 132).Adjusting instrument cluster
illumination
Use the reset button1 to adjust the illu-
mination brightness for the instrument
cluster and the switches on the center
console.
To brighten illumination
Turn the reset button1 clockwise.
The instrument cluster illumination will
brighten.
To dim illumination
Turn the reset button1 counterclock-
wise.
The instrument cluster illumination will
dim.
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warn-
ing/indicator lamps, malfunction/warning
messages or the failure of any systems.
Driving characteristics may be impaired.
If you must continue to drive, do so with
added caution. Visit an authorized
Mercedes-Benz Center as soon as possible.
iThe instrument cluster illumination is
dimmed or brightened to suit ambient light
conditions.

121 Controls in detail
Control system
Menus, submenus and functions
Menu1Menu2Menu3Menu4Menu5Menu6Menu7
Standard display722 Edition1
1Only Mercedes-Benz SLR McLaren 722 Edition.
AUDIOVehicle status
message memory2
2The Vehicle status message memory menu is only displayed if there is a message stored.
SettingsTrip computerTelephone
(page 122)(page 123)(page 126)(page 128)(page 129)(page 139)(page 141)
Commands/submenus
Digital speedome-
ter/Outside tem-
peratureEngine oil tem-
peratureSelecting
radio stationCalling up vehicle
malfunction, warn-
ing and system sta-
tus messages
stored in memoryResetting to fac-
tory settingsFuel consumption
statistics since startLoading
phone book
Calling up mainte-
nance service
displayVehicle supply
voltageOperating the
CD playerInstrument clus-
ter submenuFuel consumption
statistics since the
last resetSearching for
name in
phone book
Checking tire
inflation pressureRACETIMERTime submenuResetting fuel con-
sumption statistics
Overall analysisLighting submenuDistance to empty
Lap analysisVehicle submenu
iThe headings used in the menus table are
designed to facilitate navigation within the sys-
tem and are not necessarily identical to thoseshown in the control system displays. The first
function displayed in each menu will automati-
cally show you which part of the system you are in.

129 Controls in detail
Control system
Settings menu
In the
Settings menu there are two
functions:

The function Press reset button for
3 seconds
with which you can reset
most the settings to those set at the
factory.

A collection of submenus with which
you can make individual settings for
your vehicle.
The following settings and submenus are
available:Resetting to factory settings
You can reset the functions of most sub-
menus to the factory settings.
For safety, the
Light circuit Headlamp
mode
submenu in the Lighting menu can
be reset with the vehicle at standstill only.
Press button è or ÿ repeatedly
until the
Settings... menu appears in
the multifunction display.
Press the reset button in the instru-
ment cluster (
page 114) for approxi-
mately 3 seconds.
In the right multifunction display you
will see the request to press the reset
button again to confirm.
Press the reset button again.
The functions of most the submenus
will reset to factory settings.
FunctionPage
Resetting to factory settings129
Submenus in the Settings menu130
Instrument cluster submenu132
Time submenu133
Lighting submenu134
Vehicle submenu138
iThe settings you have changed will not be re-
set unless you confirm the action by pressing the
reset button a second time. After approximately
5 seconds, the
Settings... menu reappears
in the multifunction display.

131 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterTimeLightingVehicle
(page 132)(page 133)(page 134)(page 138)
Selecting digital speedometer
display modeSetting time (hours)Setting daytime running lamp
mode (USA only)Setting station selection mode
(radio)
Selecting standard displaySetting time (minutes)Setting locator lightingSetting automatic locking
Selecting languageSetting night security illumina-
tion (Headlamps delayed
switch-off)
Setting interior lighting delayed
switch-off