check engine MERCEDES-BENZ SPRINTER 2016 MY16 Operator’s Manual

Further information can be obtained at any
qualified specialist workshop.
Steering
Service product: power steering fluid
Product name/numberMaintenanceinterval
Mobil ATF‑D,
Exxon Mobil Corporation
or equivalent
MB Sheet No. 236.3—
The steering is maintenance-free. Further infor-
mation can be obtained at any qualified special-
ist workshop.
Brake fluid
GWARNING
The brake fluid constantly absorbs moisture
from the air. This lowers the boiling point of
the brake fluid. If the boiling point of the brake
fluid is too low, vapor pockets may form in the
brake system when the brakes are applied
hard. This would impair braking efficiency.
There is a risk of an accident.
You should have the brake fluid renewed at
the specified intervals.
!Brake fluid corrodes paint, plastic and rub-
ber. If paint, plastic or rubber has come into
contact with brake fluid, rinse with water
immediately.
Only use brake fluids approved for Sprinter vehi-
cles. Always check for the identification DOT 4
plus.
Information about approved brake fluids can be
found in the Maintenance Booklet or obtained at
any qualified specialist workshop.
Service product:
brake fluid
Product descrip-
tion and numberIntac B026E
RBoiling point: 500 ‡
(260 †)
RWet boiling point:
356 ‡ (180 †)
MB Sheet No.331.0
Maintenance
interval2 years
iHave the brake fluid renewed every 2 years
at a qualified specialist workshop.
There is usually a notice in the engine com-
partment to remind you when the next brake
fluid change is due.
Coolant
Important safety notes
GWARNING
If antifreeze comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is a risk of fire and injury.
Let the engine cool down before you add anti-
freeze. Make sure that antifreeze is not spilled
next to the filler neck. Thoroughly clean the
antifreeze from components before starting
the engine.
!Take care not to spill any coolant on painted
surfaces. You could otherwise damage the
paintwork.
When handling, storing and disposing of coolant
and antifreeze, please observe the relevant reg-
ulations and the safety notes in the "Service
products and capacities" section (
Ypage 277).
Coolant additive with antifreeze
requirements
!Use only approved antifreeze/corrosion
inhibitor that complies with MB Specification
for Service Products, Sheet Number 325.
Using other, non-approved antifreeze/corro-
sion inhibitors may cause damage to the cool-
Service products and capacities283
Technical data
Z

ant system and reduce the engine's service
life.
Coolant is a mixture of water and antifreeze/
corrosion inhibitor. It performs the following
tasks:
Rcorrosion protection
Rantifreeze protection
Rraises the boiling point
When the vehicle is first delivered, it is filled with
a coolant mixture that ensures adequate anti-
freeze and corrosion protection. Coolant must
be used in the system all year round to ensure
anti-corrosion protection and a raised boiling
point – even in countries with high outside tem-
peratures.
To prevent damage to the engine cooling sys-
tem, use only approved corrosion inhibitor/anti-
freeze that comply with the Mercedes-Benz
Specifications for Service Products.
We recommend corrosion inhibitor/antifreeze
that meets the requirements in MB Specifica-
tions for Service Products Sheet Number 325.
Check the antifreeze/corrosion inhibitor con-
centration in the coolant every six months.
The percentage of corrosion inhibitor/anti-
freeze additive in the engine cooling system
should:
Rbe at least 50%. This way, the engine cooling
system is protected against freezing down to
approximately -35 ‡ (-37 †).
Rnot exceed 55% (antifreeze protection down
to -49 ‡[-45 †]) .Otherwise ,hea twill no tbe
dissipated as effectively.
If ther e
h
as bee ncoolan tloss, do no trefil lonly
wit hwater .If th evehicle has los tcoolant, add
equa lparts water an dcorrosion inhibitor/anti -
freez eadditive .The water use das par tof th e
coolan tmixture mus tfulfil lcertain require-
ments; these are usually fulfilled by drinking
water .If th ewater quality is no tsufficient, you
mus ttreat th ewater .
Service product :coolant
Product name/number
EURO Peak Coolant/Antifreeze,
OL DWORLD INDUSTRIE S
MB Sheet No .325. 0
Zerex G05 ,The Valvolin eCompan y
MB Sheet No .325. 0
Zerex G48 ,The Valvolin eCompan y
MB Sheet No .325. 0
Glysanti nG05 ,BASF AG
MB Sheet No .325. 0
Capacities
Engine cooling syste m
CoolantApprox.10.7 5qt
(10. 0l)
Refrigeran t
The air-conditionin gsyste muse sth erefrigeran t
R‑134a. Thi srefrigeran tdoe sno tdamage th e
ozon elayer .
Product name/numberMaintenance
interva l
Refrigeran t R‑134a
MB Sheet No .361. 0—
Further information can be obtained at an y
qualifie dspecialis tworkshop .
Washer fluid
Importan tsafet ynotes
GWARNING
Windshield washer concentrat ecould ignit eif
it come sinto contact wit hhot engin ecompo-
nent sor th eexhaus tsystem. There is aris kof
fir ean dinjury.
Mak esur ethat no windshield washer con-
centrat eis spilled next to th efiller neck .
284Service pr oducts and capacities
Technical data