climate control Mercury Mariner 2010 Scheduled Maintenance Guide
[x] Cancel search | Manufacturer: MERCURY, Model Year: 2010, Model line: Mariner, Model: Mercury Mariner 2010Pages: 48, PDF Size: 0.28 MB
Page 9 of 48

Tires
Proper tire maintenance and replacement are critical to your vehicle’s performance and helps keep you and
your passengers safe. Only use replacement tires and wheels that are the same size, load index,
speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally
provided by Ford. The recommended tire and wheel size may be found on either the Safety
Compliance Certification Label or the Tire Label which is located on the B-Pillar or edge of the driver’s door.
If this information is not found on these labels then you should consult your Ford Dealer. Use of any
tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could
result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle or transfer
case/power transfer unit failure. If you have questions regarding tire replacement, see an authorized
dealer. When you need to replace your tires, please visit your Ford or Lincoln Mercury Dealership for name-brand
tires and people who know your vehicle.
If your Ford or Lincoln Mercury dealership sells the name-brand tire, they can also honor the tire
manufacturer’s warranty.
Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of
use (load, speed, inflation, etc.) the tires experience throughout their lives. In general, tires should be
replaced after 6 years, regardless of tread wear. However, heat caused by hot climates or frequent high loading
conditions can accelerate the aging process and may require the tires to be replaced more frequently.
You should replace your spare tire when you replace your road tires or after 6 years due to aging even if
the tire has not been used.
YOKOHAMA
KEEPITGENUINE
Scheduled Maintenance9
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Keep It Genuine
Page 16 of 48

30,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission fluid level on
vehicles if equipped with dipstick. Consult
your dealer for particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
37,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
16Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Page 19 of 48

52,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
60,000 miles
❑Change engine oil and replace oil filter❑Change automatic transmission fluid and filter on
all vehicles equipped with the TorqShift
transmission. Consult your dealer for your particular
requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance19
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs
Page 22 of 48

90,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission fluid level on
vehicles if equipped with dipstick. Consult
your dealer for your particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace spark plugs❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
97,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
22Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Page 24 of 48

120,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filters (if
equipped)
❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Change automatic transmission fluid and filter on
all vehicles equipped with the TorqShift
transmission. Consult your dealer for your particular
requirements.
❑Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
24Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Page 27 of 48

150,000 miles
❑Change engine oil and replace oil filter❑Change Motorcraft Premium Gold Engine Coolant
(see Exceptions on page 47 and Premium Gold
Coolant Change Record on page 48)
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Change automatic transmission fluid and filter
(filter not required on 6F35). (Except vehicles
equipped with the TorqShift transmission).
❑Change manual transmission fluid❑Change rear axle lubricant on all rear wheel
drive (RWD) vehicles (see pages 41 and
47).
❑Change transfer case fluid (4x4 only)❑Change front differential fluid (4x4 only)❑Replace wheel bearings (if non-sealed bearings)❑Replace accessory drive belt(s) if not
replaced in the last 100,000 miles (160,000 km)
❑Inspect steering linkage, ball joints, suspension, tie
rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance27
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs
Page 31 of 48

30,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter (except Focus with
PZEV engine)
❑Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
❑Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect transmission fluid level (if equipped with
an underhood dipstick).
❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
37,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULECARS& CUVS
Scheduled Maintenance31
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Cars & CUVs
Page 33 of 48

52,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
60,000 miles
❑Change engine oil and replace oil filter❑Replace climate-controlled seat filter (if equipped)❑Replace cabin air filter (if equipped)❑Replace engine air filter (except Focus with PZEV
engine)
❑Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
❑Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect transmission fluid level (if equipped with
an underhood dipstick).
❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULECARS& CUVS
Scheduled Maintenance33
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Cars & CUVs
Page 35 of 48

90,000 miles
❑Change engine oil and replace oil filter❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter (except Focus with
PZEV engine)
❑Replace cabin air filter (if equipped)❑Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
❑Replace spark plugs❑Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belt(s)❑Inspect transmission fluid level (if equipped with
an underhood dipstick).
❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
97,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULECARS& CUVS
Scheduled Maintenance35
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Cars & CUVs
Page 37 of 48

120,000 miles
❑Change engine oil and replace oil filter❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter (except Focus with
PZEV engine)
❑Replace cabin air filter (if equipped)❑Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
❑Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belt(s)❑Inspect transmission fluid level (if equipped with
an underhood dipstick).
❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULECARS& CUVS
Scheduled Maintenance37
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Cars & CUVs