light Mercury Mercury Cougar 1997 s Owner's Guide

70
*
[CF18700( BC )05/96]
To set the autolamp:
*
[CF18900( BC )05/96]
1. Make sure the headlamp control is in the
OFF position. If the control for the
headlamps is ON, you cancel the autolamp.
*
[CF19000( BC )05/96]
2. Turn the ignition key to ON or start your
vehicle.
[CF19100( BC )12/95]
3. Find the autolamp thumbwheel to the right
of the panel dim thumbwheel.
[CF19200( BC )12/95]
4. Turn the thumbwheel up to the beginning of
the MAX position (within the DELAY range).
*
[CF19300( BC )05/96]
5. The autolamp automatically turns the lamps
on and off for you.
[CF19400( BCGV)05/96]
Do not put any articles on top of the photocell
that is located in the top right corner of the
instrument panel. This photocell controls the
autolamp. If you cover it, the photocell reacts as
if it is nighttime, and the lamps turn on.
[CF19500( BC )04/96]
To turn the autolamp off, move the thumbwheel
back to OFF.
*
[CF19700( BCGV)05/96]
You can set the autolamp so the lamps stay on
for up to three minutes after you turn your
vehicle off.
[CF19800( BC )12/95]
To keep the lamps on after you leave your
vehicle, turn the thumbwheel as far into the
MAX range as you want.
[CF19900( BC )12/95]
If you move the thumbwheel only slightly into
the DELAY area, your lamps will stay on for
only a moment after you turn your vehicle off.
The further you move the thumbwheel into the
DELAY area (toward the MAX position), the
longer the lamps will stay on after you turn
your vehicle off.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

71 %
*
[CF20000( ALL)01/96]
Lighting Up the Interior and Instrument
Panel
[CF20100( BC )12/95]
Manual operation
*
[CF20200( BC )05/96]
With the light control in the parking lamps or
the headlamps position, you can brighten or dim
the lights in the instrument panel. To do this,
use the thumbwheel to the left of the steering
wheel. This wheel also turns on the interior
lights with the light control on or off.
[CF20205( BC )05/96]
Turn the thumbwheel down to dim the
instrument panel light and up to brighten. Turn
thumbwheel fully upward to turn on interior
lights.
[CF20500( BC )05/96]
half page art:0010206-D
The thumbwheel controls the light on the instrument panel
and the interior light
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

73
*
[CF24100( ALL)01/96]
Ignition
%*
[CF24200( ALL)01/96]
Understanding the Positions of the Ignition
[CF24300( ALL)12/95]
quarter page art:0010035-B
The positions of the key in the ignition
*
[CF24500( BCGV)04/96]
ACC allows some of your vehicle's electrical
accessories such as the radio and the windshield
wipers to operate while the engine is not
running.
% [CF24600( ALL)12/95]
LOCK locks the steering wheel. It also locks the
automatic transmission gearshift lever.
*
[CF24700( ALL)01/96]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[CF24800( ALL)01/96]
OFF allows you to shut off the engine and all
accessories without locking the steering wheel or
the automatic transmission gearshift lever.
*
[CF24900( ALL)01/96]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[CF25000( ALL)01/96]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

75 [CF27600( ALL)12/95]
one third page art:0011292-A
The turn signal lever
%*
[CF27700( ALL)01/96]
Turn Signals
*
[CF27800( ALL)01/96]
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
*
[CF27900( ALL)01/96]
If the turn signal stays on after you turn, move
the lever back to the center (off) position.
*
[CF28000( ALL)01/96]
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the off position when you release it.
%*
[CF28200( ALL)01/96]
High Beams
*
[CF28300( ALL)01/96]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
*
[CF28400( ALL)01/96]
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

76 %
*
[CF28700( ALL)01/96]
Flashing the Lights
*
[CF28800( ALL)01/96]
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is in the on or off position.
%
*
[CF28900( ALL)01/96]
Windshield Wipers and Washer
*
[CF29000( ALL)04/96]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
[CF29100( ALL)12/95]
Rotate the end of the lever away from you to
activate the wipers. The first seven detents are
interval wipe positions, the eighth detent is the
LO position and the ninth detent is the HI
position.
[CF29200( ALL)04/96]
To turn the wipers off, turn the knob toward
you to the OFF position.
%*
[CF29300( ALL)01/96]
Variable Interval Wipers
*
[CF29400( ALL)12/95]
In addition to two speed wipers, your vehicle
has wipers that you can set to operate at
varying intervals. For example, you can set the
interval so they wipe less often when it drizzles
or more often in heavier rain.
[CF29500( ALL)12/95]
one third page art:0011293-A
The variable interval wiper on the turn signal lever
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

83
*
[CF33500( ALL)05/96]
To Set a Lower Set Speed
*
[CF33600( ALL)05/96]
q
Press and hold COAST. Release the switch
when the desired vehicle speed is reached.
OR
*
[CF33700( ALL)05/96]
q
Press and release COAST. Each press will
decrease the set speed by 1 mph (1.6 km/h).
OR
*
[CF33800( ALL)05/96]
q
Depress the brake pedal. When the desired
vehicle speed is reached, press SET ACCEL.
*
[CF33900( ALL)05/96]
To Disengage Speed Control
*
[CF34000( BCGV)05/96]
q
Depress the brake pedal.
*
[CF34100( ALL)05/96]
Disengaging the speed control will not erase the
previously programmed set speed.
*
[CF34200( ALL)05/96]
To Return to a Set Speed
[CF34300( ALL)04/96]
q
Press RESUME. For RESUME to operate, the
vehicle speed must be faster than 30 mph
(48 km/h).
[CF34400( BC )05/96]
Indicator Light (If equipped)
[CF34500( BC )05/96]
Lights when either the SET ACCEL or RESUME
switches are pressed and remains lit until it is
either disengaged or turned off.
[CF35500( ALL)03/96]Map and Reading Lamps
*
[CF35600( ALL)12/95]
Your vehicle has two map lamps for the
passenger and the driver. To turn on the map
lamps, push the switch next to each lamp.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

88 %
*
[CF39100( CGV)05/96]
Automatic Dimming Inside Rearview
Mirror (If equipped)
[CF39200( CGV)05/96]
quarter page art:0010037-C
The automatic non-glare mirror
*
[CF39300( CGV)05/96]
The electronic day/night mirror will change
from the normal state to the non-glare state
when bright lights (glare) reach the mirror. This
mirror functions at night, and has a limited
function at dusk or dawn. From the non-glare
state, the mirror will return to the normal state
after a short delay. The delay starts when the
glare goes away. The delay prevents excessive
changing of the mirror as traffic moves behind
and around the vehicle, or on rolling hills and
curves.
[CF39400( CGV)05/96]
To turn the mirror on, push the ON/OFF
switch, located on the bottom of the mirror, to
latch it in the ON position. The switch will
illuminate and the mirror will be in the
automatic dimming mode. To turn the switch
illumination and automatic dimming feature off,
push the ON/OFF switch again.
*
[CF39500( CGV)05/96]
The electronic mirror measures the brightness of
the light coming in from the rear of the vehicle.
It automatically makes a correction in the glare
state. The mirror may be turned off in either the
normal or non-glare position.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

89 [CF39600( CGV)12/95]
There are two light sensors (photocells) in this
mirror. The sensor that detects rear glare is
located inside a widow in the center of the
mirror. The second light sensor which
determines outside light level is located on the
backside of the mirror case.
*
[CF39605( CGV)05/96]
NOTE: Do not block the sensor on the
backside of the mirror (i.e., with a
parking tag, car deodorizer, etc.) since
this may impair proper mirror
performance.
*
[CF39700( CGV)05/96]
One important safety feature is that the mirror
automatically returns to the normal position
whenever the vehicle is placed in R (Reverse)
(when the mirror is in the ON position). This
feature ensures a bright clear view in the mirror
when backing up.
%
*
[CF39800( ALL)05/96]
Sun Visors
% [CF40300( ALL)04/96]
Turning on the Mirror Light on the Sun
Visors (If equipped)
[CF40400( ALL)12/95]
To turn on the visor mirror light, lift the mirror
cover.
[CF40600( BC )12/95]
one third page art:0010277-B
The mirror on the sun visor
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

91 %
*
[CF42400( BCGV)12/95]
Using the Illuminated Entry System
(If equipped)
[CF42600( BC )05/96]
The interior lights turn on when you lift the
outside door handle on the driver's side door or
when you press UNLOCK, TRUNK, or PANIC
on a programmed remote entry transmitter if
your vehicle is equipped with remote entry.
[CF42700( BCGV)05/96]
These lights automatically turn off after 25
seconds or when you turn the ignition key to
ON or ACC. The inside lights will not turn off if
you have turned them on manually or if a door
is opened.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996

97 %
*
[CF54400(MBC )03/96]
Arming the system
[CF54500(MBC )12/95]
To arm the system, do the following steps in
sequence:
*
[CF54600(MBC )01/96]
1. Remove the key from the ignition. The hood
must be closed to arm the system.
[CF54700( BC )03/96]
At this point, the anti-theft system automatically
monitors the ignition keylock cylinder. If the
lock cylinder is forcibly removed, the anti-theft
alarm system will trigger. To arm the remaining
portion of the system, follow steps 2-4.
*
[CF54800(MBC )05/96]
2. Open any door. The alarm indicator light
will start flashing to remind you to arm the
system.
[CF54900(MBC )05/96]
3. Lock the doors by using the power door
lock switch or by pressing the remote entry
transmitter LOCK control.
[CF55000(MBC )12/95]
The alarm indicator will now glow steadily.
[CF55100(MBC )12/95]
4. Close all doors. The alarm indicator light
will then remain on steadily for
approximately 30 seconds and then go out.
When the light goes out, the system is
armed.
*
[CF55200(MBC )01/96]
NOTE: Be sure to close all doors completely. If
not, the alarm indicator light will
remain on. Remember, your anti-theft
system is armed only after the alarm
indicator light remains on steadily for
approximately 30 seconds after the last
door is closed, and then goes out.
File:05rccfc.ex
Update:Fri Jun 7 13:58:04 1996