oil dipstick Mercury Milan 2009 Scheduled Maintenance Guide

Parts
Genuine Ford Collision Parts are designed, engineered, and warranted by Ford Motor Company. See your
dealer for limited warranty details. They are manufactured to the same specifications as those on your vehicle
when it was built. The right replacement parts will help maintain the value of your vehicle.
Ford recommended scheduled maintenance – In order to keep your vehicle running right, it is important to
have the systems on your vehicle checked regularly. This can help identify potential issues and prevent
major problems. Ford Motor Company recommends the following multi-point inspection be performed at every
scheduled maintenance interval to help ensure your vehicle keeps running great.
MULTI-POINT INSPECTION - Recommended at every visit
❑Check and top up fluid levels: brake, coolant recovery reservoir, manual and automatic transmission (if equipped
with an underhood dipstick), power steering and window washer
❑Inspect tires for wear and check air pressure, including spare.
❑Check exhaust system for leaks, damage, loose parts and foreign material.
❑Check battery performance.
❑Check operation of horn, exterior lamps, turn signals and hazard warning lights.
❑Check radiator, coolers, heater and air conditioning hoses.
❑Inspect windshield washer spray and wiper operation.
❑Check windshield for cracks, chips and pitting.
❑Inspect for oil and fluid leaks.
❑Inspect engine air filter.
❑Inspect half shaft dust boots, if equipped.
❑Check shocks and struts and other suspension components for leaks and damage.
❑Inspect steering and linkage.
❑Inspect accessory drive belt(s).
❑Inspect clutch operation, if equipped.
MULTI-POINTINSPECTION
Scheduled Maintenance13
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Keep It Genuine

7,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
15,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance15
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

30,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission/transaxle fluid
level on vehicles if equipped with dipstick.
Consult your dealer for particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
37,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance17
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

Batteries
The technicians at your Ford and Lincoln Mercury dealership can determine the health of your vehicle’s
battery during any service visit. The Motorcraft Tested Tough Max Series with its “long-life” design outlasted
other long-life batteries by up to 200%. That’s one reason why we stand behind this battery with a
national 3 year, free-replacement and prorated-cost thereafter up to 100 months with unlimited mileage.
Should your battery need to be replaced, consider any one of the batteries that bear the Motorcraft name.
45,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance19
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

75,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
82,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
22Scheduled Maintenance
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)

90,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission/transaxle fluid
level on vehicles if equipped with dipstick.
Consult your dealer for your particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace spark plugs❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
97,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance23
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

105,000 miles
❑Change engine oil and replace oil filter❑Change manual transmission fluid (except Escape)❑Replace cabin air filter (if equipped)❑Replace PCV valve on all light trucks under
6,000 lbs. Gross Vehicle Weight (GVW)
(except 3V engines)
❑Change rear axle fluid only on vehicles equipped
with DANA axles (see Special Operating
Conditions on page 42 and Exceptions on page
47)
❑Change Motorcraft Premium Gold Engine Coolant
(see Exceptions on page 47 and Premium Gold
Coolant Change Record on page 48)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
112,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
24Scheduled Maintenance
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)

120,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filters (if
equipped)
❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace PCV valve on all light trucks over
6,000 lbs. Gross Vehicle Weight (GVW)
(except 3V engines)
❑Change automatic transmission fluid on all
vehicles equipped with the TorqShift
transmission. Consult your dealer for your
particular requirements.
❑Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance25
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

127,500 miles
❑Change engine oil and replace oil filter❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
135,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth (vehicles with dual rear wheels
should only rotate if unusual wear is noted)
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
26Scheduled Maintenance
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)

Tires
When your tires need to be replaced, consider visiting your Ford or Lincoln Mercury dealership for
name-brand tires and people who know your vehicle. And if your Ford or Lincoln Mercury dealership sells
the name-brand tire, they can also honor the tire manufacturer’s warranty.
15,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with Zerk fittings)
❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULECARS& CUVS
30Scheduled Maintenance
2009 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide
USA(fus)