lock Mercury Mountaineer 1997 s Service Manual

Luggage rack (if equipped)
Load luggage as far back as it will
safely go without loading more
than 45 kg (100 lb) or cause the
vehicle to exceed the Gross
Vehicle Weight Rating (GVWR) or
its Gross Axle Weight Rating
(GAWR). Use the following steps
to adjust the luggage rack.
²Turn adjustment wheel
backward to unlock crossbar
and slide crossbar forward or
backward.
²Turn adjustment wheel forward
to lock crossbar.
FUEL CONSUMPTION
Fuel economy can be improved by
avoiding:
²lack of regular, scheduled
maintenance
²excessive speed
²rapid acceleration
²driving with the brake pedal
depressed
Driving
116

Number Fuse Amperage
RatingCircuits Protected
7 7.5 amp Illumination switches
8 10 amp Right headlamp, fog
lamp system
9 10 amp Autolamps
10 7.5 amp Rear blower, speed
control, GEM system,
brake interlock,
overhead console
11 7.5 amp Warning lamps
12 10 amp Liftgate wiper/washer,
front washer
13 15 amp Brake on/off switch
14 10 amp Anti-lock system
15 7.5 amp Air bag system,
instrument cluster
16 30 amp Wiper run relay
17 15 amp Cigar lighter
18 15 amp A/C system
19 25 amp Ignition coil, PCM
system
20 7.5 amp Radio, power antenna,
GEM system,
anti-theft
21 15 amp Turn/hazard flasher
22 10 amp Turn signals
23 10 amp Rear wiper system
24 10 amp Anti-theft relay
25 7.5 amp Instrument cluster,
GEM system
Roadside emergencies
122

Maxi fuses
Fuse Amps Circuits protected
8 30 amp Battery saver relay,
headlamp relay
9 50 amp Blower motor relay,
blower motor
10 30 amp Power seats, power
lumbar, door
lock/unlock relays,
accessory delay relay
11 20 amp Horn relay,
Powertrain control
module (PCM)
12 - Not used
13 60 amp Hazard flasher, brake
ON/OFF switch, cigar
lighter, power
antenna, power
mirrors, autolamps,
instrument cluster,
GEM, radio, blower
motor relay
14 60 amp Ignition switch
Mini fuses
Fuse Amps Circuits protected
1 30 amp Premium sound
2 15 amp Liftgate wiper relays
3 30 amp Auxiliary power
4 10 amp Air bag diagnostic
monitor
5 - Not used
Roadside emergencies
126

Relay number Circuits connected
1 Wiper run relay
2 Horn relay
3 Wiper HI/LO relay
4 WOT A/C relay
5 PCM power relay
6 Fuel pump relay
Diode number Circuits connected
1 ABS diode
2 PCM diode
CHANGING TIRES
Tire change procedure
1. Park on a level surface.
2. Activate the hazard flashers.
3. Set the parking brake.
4. Place the gearshift in P (Park).
5. Block the diagonally opposite
wheel.
6. Remove the jack and lug
wrench.
Roadside emergencies
128

7. Remove the jack handle (located
underneath rear seat).
8. Assemble the jack handle to the
lug wrench.
9. Insert drive section of the jack
handle into the actuator hole and
turn counterclockwise until the
cable is slack enough to allow
spare tire to be pulled rearward
from under the vehicle.
10. Slide spare tire rearward and
remove retainer.
Roadside emergencies
129

Position the jack under the rear
axle to raise the rear wheel.
14. Turn the jack handle clockwise
and raise the vehicle until the tire
just clears the ground.
15. Remove the wheel lug nuts and
flat tire, and install the spare.
16. Install the lug nuts and tighten
until snug.
Use of wheel or lug nuts
other than original
equipment could cause damage
to the wheel or mounting system
and allow the wheels to come off
while the vehicle is in motion.
17. Lower the vehicle and tighten
the wheel lug nuts as shown.
18. Unblock the wheels and put
the flat tire, jack, jack handle and
lug wrench away.
Stowing flat tires
Stow aluminum wheel and tire
with valve stem down.
1
4
2
5 3
Roadside emergencies
131

come on unexpectedly; always
turn the engine off and let it
cool.
The cooling fan is
automatic and may come
on at any time. Always
disconnect the negative terminal
of the battery before working
near the fan.
²Never get under a vehicle
supported only by a jack. If you
must work under a vehicle, use
safety stands.
²Keep all lit cigarettes and other
smoking materials away from
the battery and all fuel-related
parts.
Working with the engine off
1. Set the parking brake and make
sure that the gearshift is securely
latched in P (Park).
2. Turn the engine off and remove
the key from the ignition.
3. Block the wheels to prevent the
vehicle from moving unexpectedly.
0020406080100
120
140
160
180
200P RND21
000000oooo
MPH km/h
UNLEADED
FUEL ONLY
RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ON
SRS
- +H
H
L L
Maintenance and care
137

Working with the engine on
1. Set the parking brake and make
sure that the gearshift is securely
latched in P (Park).
2. Do not work on a vehicle in an
enclosed space with the engine
running.
3. Block the wheels to prevent the
vehicle from moving unexpectedly.
4. If work must be done with the
engine running, avoid wearing
loose clothing or jewelry that could
get caught in moving parts. Take
appropriate precautions with long
hair.
Opening the hood
1. Inside the vehicle, pull the hood
release handle located under the
steering column.
2. While applying downward
pressure on the hood, push the
hood latch handle located behind
the grille near the center front of
the vehicle to the left.
3. Lift the hood.
After closing the hood, try to lift it
to be sure that it is closed
securely.
Lubricate the hood latch every six
months to ensure proper
operation.
0020406080100
120
140
160
180
200P RND21
000000oooo
MPH km/h
UNLEADED
FUEL ONLY
RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ON
SRS
- +H
H
L L
Maintenance and care
138

3. Let the engine idle for at least
one minute.
4. The relearning process will
automatically complete as you
drive the vehicle.
²If you do not allow the engine to
relearn its idle, the idle quality
of your vehicle may be adversely
affected until the idle is
eventually relearned.
²If the battery has been
disconnected or a new battery
has been installed, the clock and
preset radio stations must be
reset once the battery is
reconnected.
²Always dispose of used
automotive batteries in a
responsible manner. Follow your
community's standards for
disposal. Call your local
recycling center to find out
more about recycling automotive
batteries.
Maintenance and care
155

To make reaching the wiper blades
easy, simply turn the ignition to
the ON position and turn the
wipers on. Wait for them to reach
a vertical position and turn the
ignition to LOCK. Do not move the
wipers manually across the
windshield as this may cause
damage to the wipers.
Inspect the wiper arm pivots on a
regular basis to ensure that the
wiper arms move freely. Lubricate
the pivot points as necessary.
Replacing wiper blades
If the wiper blades do not work
properly after cleaning,
replacement of the blade assembly
or the blade element may be
necessary.
There are two different length
wiper blades on your vehicle. The
windshield wiper blades are 45 cm
(17.75 in) long and the liftgate
wiper is 34.9 cm (13 3/4 in) long.
Make sure you install the correct
size wiper blade in the correct
location.
To replace windshield wiper
blades:
1. Pull the wiper arm away from
the windshield and lock it into the
service position.
2. Turn the blade at an angle from
the wiper arm. Depress lock tab
and push wiper mounting arm
away from wiper blade assembly.
3. Attach the new wiper blade by
pulling wiper mounting arm down
Maintenance and care
157