Mercury Mystique 1996 s Owner's Guide

28
*
[SR22650(ALL)05/95]
RWARNING
Always keep the buckle release button pointing upward
and away from the child seat, with the tongue between
the child seat and the release button as shown in the
following illustration.
[SR22700(ALL)03/95]
17-1/2 pica
art:0001209-B
Safety belt buckle placement for child seats
File:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

Safety Restraints
29
%*
[SR22750(ALL)11/94]
Installing Child Safety Seats in the Front Passenger
Seat and Outer Rear Seating Positions
[SR22800(ALL)04/95]
Your vehicle is equipped with a dual locking mode retractor on
the shoulder belt portion of the combination lap/shoulder safety
belt for the right front seat passenger and rear outer passengers.
*
[SR22850(ALL)03/95]
If you choose to install a child safety seat in the front seating
position, move vehicle seat as far back as possible.
*
[SR22900(ALL)03/95]1.
Position the child seat in center of passenger seat.
*
[SR22950(ALL)03/95]2.
Pull down on shoulder belt, then grasp shoulder belt and lap
belt together. Figure 1.
[SR23000(ALL)02/94]
17-1/2 pica
art:0001270-AFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

30
*
[SR23050(ALL)05/95]3.
While holding the shoulder and lap belt portions together,
route the tongue through the child seat according to the
child seat manufacturer's instructions. See Figure 2. Be sure
that the belt webbing is not twisted.
[SR23100(ALL)02/94]
17-1/2 pica
art:0001271-AFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

Safety Restraints
31
[SR23150(ALL)02/94]
17-1/2 pica
art:0001272-AFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

32
[SR23200(ALL)01/95]4.
Grasp the shoulder portion of the belt and pull downward
until all of the belt is extracted from the reel and a click is
heard. At this time the retractor is in the automatic locking
mode (child restraint mode). Figure 4.
[SR23250(ALL)04/94]
24 pica art:0001273-AFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

Safety Restraints
33
[SR23300(ALL)03/95]5.
Allow the belt to retract. Pull up on the shoulder webbing. A
clicking sound will be heard as the belt retracts. This
indicates the retractor is in the automatic locking mode. Push
down on the child seat while you pull up on the belt to
remove any slack in the belt. Figures 5 and 6.
[SR23350(ALL)05/94]
17-1/2 pica
art:0001274-BFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

34
[SR23400(ALL)02/94]
17-1/2 pica
art:0001275-AFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

Safety Restraints
35
*
[SR23450(ALL)03/95]6.
Before placing the child in the child seat, forcibly tilt the seat
from side to side, and tug it forward to make sure that the
seat is securely held in place, Figure 7.
[SR23500(ALL)05/94]
17-1/2 pica
art:0001276-BFile:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

36
*
[SR23550(ALL)11/94]7.
Double check that the retractor is in the automatic locking
mode. Try to pull more belt out of the retractor. If you
cannot, the belt is in the automatic locking mode, Figure 8.
[SR23600(ALL)05/94]
17-1/2 pica
art:0001277-B[SR23650(ALL)02/94]8.
Check to make sure that the child seat is properly secured
prior to each use. If the belt is not locked, repeat steps 4
through 7.
[SR23700(ALL)02/94]
To remove retractor from automatic lock mode, unbuckle the
belt and allow the webbing to retract fully. A click will be
heard as the belt retracts. The belt is back in normal operating
mode (vehicle sensitive emergency locking mode) when this
click disappears.
File:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996

Safety Restraints
37
*
[SR23800(ALL)05/95]
RWARNING
Carefully follow all of the manufacturer's instructions
included with the safety seat you put in your vehicle. If
you do not install and use the safety seat properly, the
child may be injured in a sudden stop or collision.
[SR23900(ALL)05/95]
Installing Child Safety Seats in the Rear Center Seating
Position
[SR24000(ALL)05/95]
Some child safety seats are too wide to fit in the rear center
seat. Choose a child safety seat with a narrow base that can fit
between the safety belt buckles.
*
[SR24800(ALL)05/95]
Attaching Safety Seats With Tether Straps
*
[SR24850(ALL)05/95]
Some manufacturers make safety seats that include a tether
strap that goes over the back of the vehicle seat and attaches to
an anchoring point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of your child safety
seat for information about ordering a tether strap.
[SR24901(ALL)05/95]
To install a tether from a child safety seat in the front seat,
route the tether strap under the vehicle seat head restraint and
hook the tether hook into the hole in the tongue of the center
rear lap belt. After the hook is in the hole, pull on the loose end
of the lap belt webbing to shorten the belt and tighten the
tether strap.
[SR25650(ALL)05/95]
To install a tethered child safety seat in the rear seat, you will
need tether anchorage hardware.
[SR25700(ALL)05/95]
Tether anchorage hardware (Canadian vehicles only)
[SR25800(ALL)05/95]
All vehicles built for sale in Canada include a tether anchor
hardware kit for use with child safety seats. Attachment holes
(at each rear seating position) have been provided in your
vehicle to attach the anchor hardware, if required. Additional
kits can be obtained at no charge from any Ford or
Lincoln-Mercury dealer.
File:cdsrz.ex
Update:Fri Feb 23 11:09:40 1996