Mercury Mystique 1996 s Manual Online

Instrument Panel Controls
79
[IP33150(ALL)01/95]
Turning On the Map Lamps (If equipped)
*
[IP33200(ALL)01/94]
Your vehicle may have a map lamp for the passenger and one
for the driver.
[IP33250(ALL)11/93]
7-1/2 pica art:0001218-A
Turning on the map lamps
[IP33400(ALL)11/93]
Traction Control System (If equipped)
[IP33500(ALL)05/94]
This button turns the traction control system off and on. See
Driving Your Vehiclefor more information.
[IP33600(ALL)05/94]
6 pica art:0001179-C
The button for the traction control system
File:cdipz.ex
Update:Fri Feb 23 11:07:15 1996

80
[IP33700(ALL)11/93]
Clock
[IP34200( Z)04/94]
7-1/2 pica art:0001296-A
The digital clock
*
[IP34300(ALL)05/95]1.
To set the hour, press and hold the hour button. When the
desired hour appears, release the button.
*
[IP34400(ALL)05/95]2.
To set the minutes, press and hold the minute button. When
the desired minute appears, release the button.
[IP34500(ALL)01/95]3.
To switch between a 12-hour clock and a 24-hour clock,
press both the hour and minute buttons at the same time.
Reset the time as above.
File:cdipz.ex
Update:Fri Feb 23 11:07:15 1996

81
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side of the steering
column to:
*
[SC00700(ALL)03/95]
n
operate the turn signals and cornering lamps
*
[SC00800(ALL)01/95]
n
turn the high beams on/off
*
[SC00900(ALL)05/95]
n
flash the lamps
*
[SC01100(ALL)01/95]
Turn Signals
[SC01200(ALL)01/95]
10-1/2 pica
art:0001186-D
The turn signal lever
*
[SC01300(ALL)03/95]
Move the lever up to signal a right turn. Move it down to
signal a left turn. The corresponding indicator light in the
instrument cluster will flash.
*
[SC01400(ALL)03/95]
If the turn signal stays on after you turn, move the lever back
to the center (off) position.
*
[SC01500(ALL)03/95]
For lane changes, move the lever far enough to signal but not to
latch. The lever will return to the off position when you release
it.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

82
*
[SC02800(ALL)05/95]
High Beams and Flashing the Lamps
[SC02900(ALL)05/95]
To turn on the high beams, turn the headlamp control knob to
the headlamp ON position and push the turn signal lever away
from you until it latches. When the high beams are on, the high
beam indicator light on the instrument cluster comes on.
[SC03000(ALL)10/93]
To turn off the high beams, pull the lever back to the off
position.
*
[SC03400(ALL)06/95]
To flash the headlamps, pull the lever toward you for a moment
and then release it. The headlamps will flash whether the
headlamp knob is in the on or off position.
*
[SC03700(ALL)03/95]
Windshield Wipers and Washer
*
[SC03800(ALL)03/95]
To turn on the windshield wipers, the ignition key must be
turned to the ON or ACC position.
[SC04400(ALL)05/95]
10-1/2 pica
art:0001189-D
Using the windshield wiper
[SC04500(ALL)02/94]
The windshield wipers can be set on high, low speed or interval
wipe. Turn the ring on the lever to set a longer or shorter pause
between wiping cycles.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Steering Column Controls
83
*
[SC04950(ALL)05/95]
Windshield Washer
[SC05000(ALL)01/95]
When the lever is pulled to activate the windshield washer, the
wipers operate for about three cycles after the spray stops.
[SC05110(ALL)05/95]
7-1/2 pica art:0001194-D
Washing the windshield
*
[SC05310(ALL)01/95]
Do not try to clean the windshield when the washer fluid
container is empty or activate the washers at any time for more
than 15 seconds continuously. This could damage the washer
pump system.
*
[SC05350(ALL)01/93]
RWARNING
In freezing weather, the washer solution may freeze on
the windshield and obscure your vision. Always warm
up the windshield with the defroster before you use the
washer fluid. If you cannot see through the windshield
clearly, it can increase the risk of being involved in a
collision.
*
[SC05500(ALL)04/95]
For information about refilling the washer fluid or replacing
your windshield wiper blades, seeWindshield washer fluid and
Wipersin the Index.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

84
*
[SC05520(ALL)03/95]
Hazard Flasher
*
[SC05530(ALL)03/95]
The hazard flasher serves as a warning to other drivers to be
careful when approaching or passing your vehicle.
[SC05540(ALL)05/94]
10-1/2 pica
art:0001193-A
Using the hazard flasher switch
*
[SC05590(ALL)03/95]
The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery can be drained.
*
[SC05600(ALL)01/95]
Horn
*
[SC05800(ALL)03/94]
To sound the horn, push the pad in the center of the steering
wheel. Check the horn regularly to be sure it operates properly.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Steering Column Controls
85
*
[SC07400(ALL)03/91]
Speed Control (If equipped)
*
[SC07500(ALL)06/95]
If your vehicle has speed control, you can automatically
maintain a constant speed at or above 30 mph (50 km/h).
*
[SC07550(ALL)05/95]
Use of radio transmitting equipment that is not Federal
Communications Commission (FCC) or in Canada the Canadian
Radio and Telecommunications Commission (CRTC) approved
may cause the speed control to malfunction. Therefore, use only
properly installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
*
[SC07650(ALL)03/95]
NOTE: Do not shift to N (Neutral) when using the speed
control. This will cause the engine to overspeed.
*
[SC07675(ALL)05/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
[SC07700(ALL)05/94]
10-1/2 pica
art:0000262-D
The speed control switches on the steering wheel
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

86
[SC08200(ALL)04/95]
Setting the speed control
*
[SC08400(ALL)06/95]1.
Press and release the ON switch.
*
[SC08500(ALL)06/95]2.
Accelerate to the desired speed above 30 mph (50 km/h)
using the accelerator pedal.
[SC08800(ALL)05/95]3.
Press the SET ACC switch and release it immediately to set
your speed. If you keep this switch depressed, your speed
will continue to increase.
[SC08900(ALL)05/95]4.
Take your foot off the accelerator pedal. Your vehicle will
maintain the speed you set.
*
[SC09000(ALL)06/95]
If you drive up or down a steep hill, your vehicle may
momentarily slow down or speed up, even though the speed
control is on. This is normal.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Steering Column Controls
87
[SC09010(ALL)05/95]
NOTE: If your vehicle is equipped with an automatic
transaxle, and if your speed increases above your set
speed while driving in Overdrive on a downhill
grade, you may want to turn the Overdrive off and
use Drive. You may turn the Overdrive off by
pressing the Transaxle Control Switch on the left side
of the gearshift lever. This will reduce vehicle speed
if it goes above your set speed on a downhill grade.
For the best fuel economy during normal driving
conditions, leave the vehicle in Overdrive, or resume
as soon as possible.
[SC09020(ALL)05/95]
NOTE: If your vehicle is equipped with a 5-speed manual
transaxle, and if your speed increases above your set
speed while driving in 5 (Fifth) gear on a downhill
grade, you may want to shift to 4 (Fourth) gear to
reduce vehicle speed. Depressing the clutch pedal
cancels speed control, therefore speed control must be
reset by pressing the SET/ACC or RES buttons. Speed
control cannot reduce the vehicle speed if it goes
above your set speed on a downhill grade.
[SC09150(ALL)05/94]
Speed control is cancelled when Traction Control (if equipped)
becomes active.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

88
%*
[SC09200(ALL)06/95]
Accelerating With the Speed Control Operating
*
[SC09300(ALL)05/95]
You can use the accelerator pedal to speed up momentarily.
When you take your foot off the accelerator, the vehicle will
return to the set speed.
*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use one of the
following procedures:
*
[SC09415(ALL)03/95]
n
COASTÐ Press and hold the COAST switch. Release the
switch when the vehicle slows down to the desired speed.
[SC09420(ALL)05/94]
n
Tap the brake pedal. When the vehicle attains the desired
speed, press the SET ACC switch and release it immediately.
[SC09427(ALL)05/94]
n
TAP-DOWNÐ Press and then quickly release the COAST
switch. Each time you ªtapº the switch, the set speed will
decrease by 1 mph (1.6 km/h).
*
[SC09430(ALL)05/95]
If vehicle speed is reduced below 30 mph (50 km/h) by any of
the above methods, then you must manually accelerate to a
speed over 30 mph (50 km/h) and reset the system.
*
[SC09435(ALL)03/95]
To reset the speed control toa higher speed, follow one of
these procedures:
[SC09440(ALL)05/94]
n
ACCÐ Press and hold the SET ACC switch. Release the
switch when the vehicle has accelerated to the desired speed.
[SC09445(ALL)03/95]
n
Depress the accelerator pedal. When the vehicle attains the
desired speed, press and release the SET ACC switch.
[SC09452(ALL)05/94]
n
TAP-UPÐ Press and then quickly release the SET ACC
switch. Each time you ªtapº the switch, the set speed will
increase by 1 mph (1.6 km/h).
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996