lock Mercury Sable 1996 s User Guide

45
*
[SR23601(ALL)11/94]
7. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode,
Figure 8.
*
[SR23650(ALL)04/95]
half page art:0011245-B
Checking the retractor
[SR23701(ALL)11/94]
8. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR23750(ALL)03/95]
NOTE: To remove the retractor from automatic
lock mode, allow seat belt to retract
fully to its stowed position and the
retractor will automatically switch back
to the vehicle sensitive locking mode
for normal adult usage.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

46
*
[SR24750(ALL)01/95]
RWARNING
When using any infant or child
restraint system, it is important that
you follow the instructions and
warnings provided by the
manufacturer concerning its
installation and use. Failure to follow
each of the restraint manufacturer's
instructions could increase the risk or
severity of an injury in the event of
a collision or sudden stop.
%*
[SR24800(ALL)04/95]
Attaching Safety Seats With Tether Straps
*
[SR24950(ALL)04/95]
Some manufacturers make safety seats that
include a tether strap that goes over the back of
the vehicle seat and attaches to an anchoring
point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of
your child safety seat for information about
ordering a tether strap.
*
[SR25050(ALL)04/95]
Front Seats
*
[SR25150(ALL)04/95]
To install a tether from a child safety seat in the
front seat:
*
[SR25250(ALL)04/95]
1. Buckle the lap/shoulder belt (in the seat
directly behind the front passenger seat in
which the child safety seat will be installed).
*
[SR25350(ALL)04/95]
2. Pull all the stored belt out of the rear seat
retractor to switch the retractor to automatic
locking mode.
*
[SR25375(ALL)04/95]
3. Let the retractor wind up the slack from the
lap/shoulder belt.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

47
*
[SR25425(ALL)04/95]
4. Install the child safety seat in the front seat.
Refer to the previous section onInstalling
Safety Seats. Hook the tether strap hook
around the webbing near the center of the
shoulder portion of the locked lap/shoulder
belt.
*
[SR25525(ALL)04/95]
5. Tighten the tether strap.
*
[SR25550(ALL)04/95]
Rear Seats
*
[SR25600(ALL)04/95]
If you use a tethered safety seat on one of the
rear seats, you can anchor the strap to the
appropriate tether anchor directly behind that
seat position.
[SR25725(ALL)04/95]
Tether anchorage hardware
[SR25800(ALL)04/95]
Attachment holes (at each rear outboard seating
position) have been provided in your vehicle to
attach anchor hardware, if required. Kits can be
obtained at no charge from any Ford or
Lincoln-Mercury dealer.
[SR26100(ALL)04/95]
Be sure to follow the child safety seat
manufacturer's instructions.
*
[SR26500(ALL)04/95]
RWARNING
Tighten the anchor according to
specifications. Otherwise, the safety
seat may not be properly secured and
the child may be injured in a sudden
stop or collision.
[SR26600(ALL)04/95]
In a station wagon, you simply attach the tether
strap to one of the anchors that are already
installed for you.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

49 [SR26900(ALL)04/95]
Built-In Child Seat (Wagon Ð If equipped)
[SR26950(ALL)04/95]
The second row seat may include an optional
built-in child safety seat on the passenger side.
The child restraint is to be usedonlyby children
who are at least one year old, weigh between 9
and 27 kilograms (20 and 60 pounds) and whose
shoulders (top) are below the shoulder harness
slots in the seatback.
*
[SR27000(ALL)04/95]
If your child is less than one year old or weighs
less than 9 kilograms (20 pounds),alwaysuse a
rear facing infant or convertible seat because a
child of that size is not sufficiently developed to
withstand crash forces in a front facing position.
Follow the specific manufacturer's instructions
for weight and height restrictions.
*
[SR27051(ALL)03/95]
Children must be properly buckled before riding
in the vehicle. It is the law in every state and
province. This child seat conforms to all
Federal/Canadian motor vehicle safety
standards.
*
[SR27100(ALL)03/95]
Built-in child seat belt retractors
*
[SR27150(ALL)04/95]
The belts on the built-in child seat are equipped
with a retractor that locks when both belt
tongues are latched into the crotch safety belt
buckled.
[SR27251(ALL)04/95]
The retractor will automatically snug the belts
around the child. Frequently check the child
seat's lap and shoulder harness belts for correct
placement and tightness. Use the child seat only
if the harness belts will stay snug with a child
buckled in the seat. If belts do not remain snug,
take the vehicle to the dealer for child seat
repair.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

53 [SR28125(ALL)04/95]
one third page art:0001456-B
Figure 5: Shoulder safety belt placement on the child
[SR28150(ALL)04/95]
NOTE: Read the following steps carefully to
become familiar with the indicator
windows located on each safety belt
tongue and the chest clip. When either
of the tongues or the chest clip is
unbuckled, the color red appears in the
window. When the tongues or chest
clip are securely buckled, the color
green appears.
[SR28200(ALL)04/95]
7. Insert either the left or right safety belt
tongue into the single opening of the crotch
safety belt buckle as shown in Figure 6. (It
does not matter which tongue is inserted
first.) Then insert the other tongue. Allow
belts to retract and fit snugly.
[SR28220(ALL)12/95]
NOTE: The indicator window on each tongue
must appear green when buckled.
[SR28240(ALL)12/95]
NOTE: If a belt locks during extraction, allow
belts to retract FULLY and repeat
procedure.
*
[SR28250(ALL)04/95]
RWARNING
If both tongues do not latch in the
buckle, do not use the child seat. See
your dealer for repairs.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

57 [SR28550(ALL)04/95]
9. Pull the shoulder belts out to ensure that the
crotch safety belt buckle is securely fastened
and the retractor is locked. Refer to Figure 8.
[SR28575(ALL)04/95]
half page art:0001455-B
Figure 8: Checking for securely latched buckle and locked
retractor
[SR28600(ALL)04/95]
10. If the belts become too tight, unbuckle the
crotch safety belt buckle allow belts to
retract, then reinsert both belt tongues.
[SR28650(ALL)04/95]
To remove the child from the built-in child
seat:
[SR28700(ALL)04/95]
1. Squeeze the tabs on the top and bottom of
the chest clip and pull the halves apart to
open the chest clip. Refer back to Figure 7.
[SR28750(ALL)04/95]
2. Press the release button on the crotch safety
belt buckle.
[SR28800(ALL)04/95]
3. Slide the shoulder belts off the child's
shoulders and remove the child. Refer back
to Figure 5.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

58 [SR28850(ALL)04/95]To stow the built-in child seat:
*
[SR28900(ALL)03/95]
1. Return the child seat cushion to the upright
position.
[SR28950(ALL)04/95]
2. Press firmly in the center and top of the
child seat to place it in the stowed position.
[SR28960(ALL)12/95]
3. Reattach the flap on the child seat to the top
of the seatback.
[SR29000(ALL)03/95]
The seat can now be used by an adult or the
seatback can be folded down.
[SR29025(ALL)04/95]
NOTE: The seatback cannot be folded down
unless the child seat is fully stowed.
*
[SR29050(ALL)03/95]
Inspection after a collision
*
[SR29100(ALL)03/95]
RWARNING
All built-in child restraints, including
seats, buckles, retractors, seat latches,
interlocks, and attaching hardware
should be inspected by a qualified
Dealer technician after any collision.
If the child seat was in use during a
collision, Ford recommends replacing
it. However, if the collision was
minor and a qualified technician
finds that the child restraints do not
show damage and continue to
operate properly, they do not need to
be replaced. Built-in child seats not
in use during a collision should also
be inspected and replaced if either
damage or improper operation is
noted.
[SR29150(ALL)04/95]
Built-in child seat maintenance
*
[SR29200(ALL)03/95]
Regularly inspect the lap and shoulder belts
system of your child seat. See your Ford dealer
if the shoulder belt webbing is frayed, or if the
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

61
Starting Your Sable
*
[ST03300(ALL)03/95]
Ignition
%*
[ST03400(ALL)01/95]
Understanding the Positions of the Ignition
[ST03725(ALL)11/94]
quarter page art:0000017-D
The positions of the key in the ignition
%*
[ST04050(ALL)03/95]
ACCESSORY allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
[ST04100(ALL)10/89]
LOCK locks the steering wheel. It also locks the
gearshift for all vehicles with an automatic
transaxle.
[ST04175(ALL)03/95]
The automatic transaxle gearshift must be in P
(Park) to move the key to the LOCK position.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

62 %
*
[ST04200(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
%*
[ST04300(ALL)03/95]
If the key is stuck in the LOCK position, move
your steering wheel left or right until the key
turns freely.
[ST04325(ALL)04/95]
OFF allows you to shut off the engine and all
accessories without locking the steering wheel or
the automatic transaxle gearshift lever.
*
[ST04350(ALL)03/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST04375(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
*
[ST04500(ALL)02/95]
Removing the Key From the Ignition
[ST06000(ALL)02/95]
Procedures for removing the key from the
ignition will be the same for both the column-
and console-mounted gearshifts.
*
[ST06300(ALL)03/95]
1. Put the gearshift in P (Park).
*
[ST06400(ALL)01/95]
2. Set the parking brake fully.
[ST06500(ALL)11/94]
3. Turn the ignition to the LOCK position.
*
[ST06600(ALL)03/95]
4. Remove the key.
[ST07310(ALL)12/94]
If you have difficulty in turning the key, rotate
the steering wheel slightly because it may be
binding.
%*
[ST07520(ALL)03/95]
If the driver's door is open while the key is still
in the ignition, a warning chime sounds.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

66 [ST09420(ALL)11/94]NOTE: Your vehicle is equipped with an
automatic transaxle and has an
interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
*
[ST09480(ALL)04/95]
If the engine does not start after two attempts:
*
[ST09492(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST09494(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST09496(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST09497(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST09498(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST09500(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
%*
[ST10200(ALL)04/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle move
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995