lock Mercury Sable 1996 s Manual PDF

228 [RE12500(ALL)12/91]
one third page art:0000395-BThe lug nuts on the wheel
*
[RE12600(ALL)11/94]
7. Place any wheel covers and ornaments in the
trunk.
*
[RE12700(ALL)03/95]
8. Put the tire, jack, and wrench away. Make
sure the jack is securely fastened so it does
not rattle when you drive.
*
[RE12750(ALL)03/95]
9. Unblock the wheels.
[RE13007(ALL)04/95]
Removing and Replacing Wheel Covers
[RE13008(ALL)04/95]
Your vehicle may have wheel covers with a wire
retention system.
[RE13009(ALL)03/95]
To remove the wheel cover:
[RE13010(ALL)04/95]
Pry it loose by carefully inserting the tapered
end of the jack handle between the wheel cover
and the wheel.
[RE13011(ALL)04/95]
To replace the wheel cover:
[RE13012(ALL)04/95]
1. One of the windows on the wheel cover is
identified with a valve stem logo on the
back side of the cover. Install the wheel
cover to the wheel with the window at the
valve stem.
[RE13013(ALL)04/95]
2. Hold the wheel cover in this position and
press the cover onto the wheel with the
palm of your hand. Do not force or hammer
the cover.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

230 [RE13050(ALL)04/95]To replace the wheel cover:
[RE13070(ALL)11/94]
1. Reinstall the pedestal on the wheel before
reinstalling the wheelcover.
[RE13080(ALL)11/94]
2. One of the windows on the wheelcover is
identified with a valve stem logo on the
inside of the cover. Align this valve hole on
the wheelcover with the valve stem on the
wheel. Reinstall the cover by pressing with
the palm of your hand. Do not use excessive
force. Do not use a hammer.
[RE13090(ALL)11/94]
3. Attach the bolt to the pedestal through the
center hole in the cover with the lug wrench.
[RE14000(ALL)11/94]
4. Align the legs of the center ornament with
the slots on the wheel cover. Reinstall the
ornament by pressing with the palm of your
hand. Do not use excessive force. Do not use
a hammer.
%*
[RE14100(ALL)03/95]
Anti-Theft Wheel Lug Nuts (If equipped)
[RE14200(ALL)03/95]
If your vehicle has this feature, one of the lug
nuts on each wheel lock must be removed and
replaced with a special key. The key and
registration card are attached to the lug wrench
and stored with the spare tire. If you lose the
key, send the registration card to the
manufacturer (not to the dealer) to get a
replacement key.
*
[RE14250(ALL)03/95]
NOTE: If entire lug wrench/lug nut key
assembly is lost, see your nearest Ford
or Lincoln-Mercury dealer who has
access to a master set of keys.
[RE14275(ALL)11/94]
DO NOT USE THE KEY WITH AN IMPACT
WRENCH.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

231 [RE14300(ALL)04/95]
quarter page art:0010357-B
The anti-theft lug nut and key
*
[RE14400(ALL)03/95]
Removing the anti-theft lug nut
*
[RE14600(ALL)03/95]
Insert the key over the locking lug nut. Make
sure that you hold the key square to the lug nut.
If you hold the key on an angle, you may
damage the key and the lug nut.
*
[RE14700(ALL)03/95]
Place the lug nut wrench over the lug nut key
and apply pressure on the key with the wrench.
Turn the wrench in a counterclockwise direction
to remove the lug nut.
*
[RE14800(ALL)03/95]
Replacing the anti-theft lug nut
*
[RE14900(ALL)03/95]
Insert the key over the locking lug nut. Place the
lug nut wrench over the lug nut key and, while
applying pressure on the key, install the lug nut.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

234
*
[RE18000(ALL)03/95]
Towing Your Vehicle Behind Another
Vehicle
*
[RE18100(ALL)03/95]
At times, you may want to tow your vehicle
behind another vehicle, such as a recreational
vehicle, a car, or a truck.
*
[RE18200(ALL)03/95]
Before you have your vehicle towed:
*
[RE18300(ALL)03/95]
q
Release the parking brake.
*
[RE18400(ALL)03/95]
q
Move the gearshift to N (Neutral).
[RE18500(ALL)01/95]
q
Turn the key in the ignition to OFF.
*
[RE18600(ALL)03/95]
q
Unlock the steering wheel.
[RE18700(ALL)01/95]
Do not tow your vehicle at a speed faster than
35 mph (56 km/h) or for a distance greater than
50 miles (80 km), unless the drive wheels are
placed on dollies.
*
[RE19000(ALL)03/95]
RWARNING
Never use a tow bar that attaches to
the bumper when you tow your
vehicle. You could damage the
bumper and cause an accident.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

235
Customer Assistance
%*
[HS00205(ALL)06/94]
Roadside Assistance
*
[HS00210(ALL)08/95]
Ford Motor Company has set up a 24-hour,
seven-day-a-week hotline with trained operators
that put you in touch with the help you need if
you experience a problem with your vehicle.
This complimentary service is provided to you
throughout your warranty period of 3 years or
36,000 miles (3 years or 60,000 km), whichever
comes first. To purchase Roadside Assistance
coverages beyond this period, through Ford
Auto Club, contact your Ford or
Lincoln-Mercury dealer (not available in
Canada).
*
[HS00215(ALL)06/94]
Roadside Assistance will cover the following:
*
[HS00220(ALL)06/94]
q
Mount your spare if you have a flat tire.
*
[HS00225(ALL)06/94]
q
Jump-start your battery if it is dead.
*
[HS00230(ALL)06/94]
q
Unlock your vehicle if you are locked out.
*
[HS00235(ALL)06/94]
q
Bring you fuel if you run out.
*
[HS00240(ALL)06/94]
q
Tow your vehicle if you are stranded. Even
non-warranty related tows, like accidents or
getting stuck in mud or snow, are covered
(some exclusions apply, such as impound
towing and repossession).
*
[HS00245(ALL)06/94]
How to use Roadside Assistance
*
[HS00250(ALL)06/94]
Your Roadside Assistance identification card can
be found in the Owner Guide portfolio in your
glove compartment. Complete the card and place
it in your wallet for quick reference.
File:fchss.ex
Update:Wed Dec 20 14:28:55 1995

257
*
[SV01900(ALL)03/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000(ALL)01/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100(ALL)01/95]
q
Never get under a vehicle while it is
supported by a jack only. If you must work
under a vehicle, use safety stands.
*
[SV02200(ALL)01/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02250(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02550(ALL)03/95]
Working with the engine off:
*
[SV02600(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02625(ALL)03/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02650(ALL)03/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02700(ALL)03/95]
Working with the engine on:
*
[SV02800(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02825(ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

263 %
*
[SV05075(ALL)04/95]
Cleaning the Engine
*
[SV06000(ALL)04/95]
A clean engine is more efficient because the
engine is able to cool properly. A build up of
grease and dirt acts as an insulator, keeping the
engine warmer than normal.
*
[SV06020(ALL)04/95]
q
Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.
*
[SV06040(ALL)04/95]
q
In order to avoid possible cracking of the
engine block or fuel injection pump, do not
spray a hot engine or injection pump with
cold water.
*
[SV06060(ALL)04/95]
q
The alternator, distributor and air intake must
be covered. Covering these components will
help prevent water damage.
*
[SV06080(ALL)04/95]
q
Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.
%
*
[SV06100(ALL)03/95]
Filling the Fuel Tank
[SV06800(ALL)04/95]
1. Turn the engine off. After opening the fuel
door, remove the cap carefully and slowly
by turning it counterclockwise 1/4 turn until
it stops. Pull to remove the cap. A tether
attaches the cap to the fuel filler pipe.
[SV06825(ALL)04/95]
one inch art:0001470-AFile:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

264 [SV06850(ALL)04/95]
RWARNING
The fuel system may be under
pressure. If the fuel cap is venting
vapor or if you hear a hissing sound,
wait until it stops before completely
removing the cap. Otherwise, fuel
may spray out and injure you or
others.
*
[SV06900(ALL)03/95]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe.
*
[SV06950(ALL)02/95]
NOTE: To help reduce early nozzle shutoffs
and fuel spillage, park your vehicle so
that the fuel filler door is not
downhill. Do not tilt or turn the nozzle
upside down when filling. Avoid
excessively fast fuel dispensing rates
(over 10 gallons [38 liters] per minute).
*
[SV07150(ALL)01/95]
3. If you spill any fuel on the body of your
vehicle, clean it off immediately. The fuel
may dull or soften the paint if you do not
wash it off.
[SV07200(ALL)11/94]
4. To replace the fuel cap, align the tabs on the
cap with the notches on the filler pipe. Turn
it clockwise until it stops.
[SV07250(ALL)04/95]
5. Push the fuel door closed.
[SV07275(ALL)04/95]
If the Service Engine Soon warning light comes
on and stays on when you start the engine, the
fuel cap may not be properly seated. Turn off
the engine, remove the fuel cap and replace it,
being careful to align the cap properly. For more
information, seeWarning lightsin the Index.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

278
*
[SV18100(ALL)01/95]
Adding engine coolant
*
[SV18200(ALL)01/95]
RWARNING
Be careful when adding engine
coolant. Do not put engine coolant or
antifreeze in the container for the
windshield washer fluid. If sprayed
to clean the glass, engine coolant or
antifreeze could make it difficult to
see through the windshield.
[SV18300(ALL)11/94]
RWARNING
Never remove the pressure cap while
the engine is running or hot to avoid
personal injury that can be caused by
escaping steam or engine coolant.
[SV18500(ALL)04/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the cap.
[SV18600(ALL)02/95]
2. When the engine is cold, wrap a thick cloth
around the cap and turn it slowly
counterclockwise to relieve pressure.
*
[SV18700(ALL)03/95]
3. Step back while the pressure releases.
*
[SV18800(ALL)03/95]
4. When you are sure that all the pressure has
been released, use the cloth to turn and
remove cap.
*
[SV18900(ALL)02/95]
5. Stand away from the reservoir opening. Hot
steam may blow out or hot engine coolant
may even splash out.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

288 [SV23760(ALL)04/95]
one third page art:0001386-AInstalling the new filter
[SV23765(ALL)04/95]
5. Reinstall the water shield, sliding it from the
center of the vehicle toward the fender. As
you position it over the filter, guide the
hinged flap on the left side of the shield
down between the filter and the fender.
Slide the shield toward the fender until the
holes on the shield align with the holes on
the vehicle body. Reinstall the two screws
that hold the shield in place.
[SV23770(ALL)04/95]
6. Reinstall the leaf screen. Tuck the left rear
corner of the screen under the top of the
fender, then lower the screen into position.
Reinstall the four retainers, turning them 90Ê
to lock them into place. Reinstall the vacuum
line hose clips and the one loose clip in the
notches in the leaf screen.
%
*
[SV23800(ALL)03/95]
Tires
*
[SV23900(ALL)03/95]
Look at your tires each time you fill your fuel
tank. If one tire looks lower than the others,
check the pressure in all of them. Always follow
these precautions:
*
[SV24200(ALL)03/95]
q
Keep your tires inflated to the recommended
pressures.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995