instrument cluster Mercury Sable 1996 Owner's Manuals

31 %
*
[SR18450(ALL)03/95]
The air bag system uses a readiness light on the
instrument cluster and a tone to indicate the
condition of the system. When you turn the
ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and
then turn off. This indicates that the system is
operating normally. NOTE: Maintenance of the
air bag system is not required.
*
[SR18475(ALL)03/95]
A problem with the system is indicated by one
or more of the following:
*
[SR18501(ALL)03/95]
q
the readiness light will either flash or stay lit,
*
[SR18525(ALL)03/95]
q
or it will not light immediately after ignition
is turned on,
*
[SR18550(ALL)03/95]
q
or a group of five beeps will be heard. The
tone pattern will repeat periodically until the
problem and light are repaired.
*
[SR18575(ALL)03/95]
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the Air Bag
Supplemental Restraint System may not function
properly in the event of a collision.
*
[SR18601(ALL)01/95]
RWARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System; tampering could
cause activation of the system and
increase the risk of personal injury.
DO NOT REPLACE OR
OTHERWISE TAMPER WITH THE
AIR BAG FUSES. For servicing of
the Air Bag Supplemental Restraint
System, see your Ford or
Lincoln-Mercury dealer.
File:fcsrs.ex
Update:Wed Dec 20 09:34:02 1995

73
Warning Lights and
Gauges
%*
[LG00500(ALL)05/92]
In your vehicle, the warning lights and gauges
are grouped together on the instrument panel.
We call this grouping a cluster. Your vehicle has
one of the following clusters:
[LG00800(ALL)02/95]
q
Standard cluster
[LG00900(ALL)02/95]
q
Optional cluster
*
[LG01100(ALL)05/94]
If you are not sure which cluster your vehicle
has, check the diagrams on the following pages.
[LG02050(ALL)03/95]The Standard Cluster
[LG02075(ALL)02/95]
The following warning lights and gauges are on
the standard cluster. All of the warning lights
and gauges alert you to possible problems with
your vehicle. Some of the lights listed are
optional. The following sections detail what each
of these indicators means.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

115
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel
are designed to give you easy access to the
controls while you are driving.
%
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side
of the steering column to:
[SC00700(ALL)03/95]
q
operate the turn signals
*
[SC00800(ALL)01/95]
q
turn the high beams on/off
*
[SC00900(ALL)01/95]
q
flash the lights
*
[SC01000(ALL)01/95]
q
turn the windshield wipers and washer
on/off
%*
[SC01100(ALL)01/95]
Turn Signals
*
[SC02201(ALL)03/95]
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
*
[SC02401(ALL)03/95]
If the turn signal stays on after you turn, move
the lever back to the center (off) position.
*
[SC02451(ALL)03/95]
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the off position when you release it.
%*
[SC02800(ALL)03/95]
High Beams
*
[SC03100(ALL)08/95]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

121
malfunction. Therefore, use only properly
installed FCC approved radio transmitting
equipment in your vehicle.
[SC08000(ALL)11/94]
one third page art:0001399-B
The speed control buttons on the steering wheel
*
[SC08200(ALL)03/95]
To set the speed control:
[SC08400(ALL)11/94]
1. Press and release the ON switch. The
CRUISE indicator light in the instrument
cluster will illuminate to indicate that speed
control is in a standby mode.
*
[SC08500(ALL)04/95]
2. Accelerate to the desired speed above
30 mph (50 km/h) using the accelerator
pedal.
*
[SC08800(ALL)03/95]
3. Press the SET ACCEL switch and release it
immediately to set your speed. If you keep
this switch pressed, your speed will continue
to increase.
*
[SC08900(ALL)03/95]
4. Take your foot off the accelerator pedal.
Your vehicle will maintain the speed you set.
*
[SC09000(ALL)01/95]
If you drive up or down a steep hill, your
vehicle may momentarily slow down or speed
up, even though the speed control is on. This is
normal.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

140 [FV10802(ALL)04/95]Coded Key Anti-Theft System
[FV10804(ALL)08/95]
If your vehicle is equipped with the coded key
anti-theft system, you can only use an
electronically coded key to start the vehicle.
During each vehicle start, the coded key is
ªreadº by the anti-theft system. If the key's ID
code matches that in the anti-theft system, the
vehicle is enabled to start. If the key's ID code
does not match the anti-theft system, or if no
coded key is detected, then the vehicle is not
able to start. Your vehicle will need to be taken
to the dealership for re-initializaiton if either of
the following situations occur:
[FV10805(ALL)07/95]
q
Both supplied keys are lost or stolen.
[FV10807(ALL)07/95]
q
Only one key has been lost, but you want to
ensure the ªlostº key will not start the
vehicle. In this case, bring the remaining
key(s) to the dealer for re-programming.
[FV10808(ALL)04/95]
THEFT indicator
[FV10810(ALL)04/95]
The anti-theft indicator (THEFT) in the
instrument cluster will light for 2 seconds and
then go out when the ignition is turned to the
ON or START position. If it does not light or if
it flashes, have the system serviced by your
dealer or a qualified technician.
[FV10812(ALL)04/95]
Programming additional keys
[FV10814(ALL)04/95]
Two electronically coded keys were supplied
with your vehicle. Additional keys can be
purchased as spares, up to a total of 16 keys. To
program a new key, use a coded key and the
following procedure:
[FV10816(ALL)04/95]
1. With the coded key in the ignition, turn the
ignition from the ON to the OFF position.
[FV10820(ALL)04/95]
2. Within 15 seconds, insert the new electronic
key in the ignition and turn it to ON or
START. The key must have the correct
mechanical cut.
File:fcfvs.ex
Update:Wed Dec 20 09:39:11 1995

200
*
[DR06802(ALL)01/95]
N (Neutral)
*
[DR06804(ALL)01/95]
With the gearshift in the N (Neutral) position,
the vehicle can be started and is free to roll.
Hold the brake pedal down while in this
position.
*
[DR06805(ALL)01/95]
Driving
%*
[DR06825(ALL)01/95]
When to use D (Overdrive)
[DR06830(ALL)11/94]
D (Overdrive) is the usual driving position for
an automatic overdrive transaxle. It
automatically upshifts or downshifts as the
vehicle speeds or slows.
[DR06835(ALL)11/94]
However, D (Overdrive) also shifts into a fourth
gear Ð an overdrive gear Ð when your vehicle
cruises at a consistent speed for any length of
time. This fourth gear will increase your fuel
economy when you travel at cruising speeds.
[DR07025(ALL)04/95]
When to use D (O/D OFF)
[DR07050(ALL)04/95]
You will notice that there is only one drive
position on your gearshift indicator (instead of
Drive and Overdrive). However, you will find a
switch labeled O/D located on the gearshift
lever. Push in the switch and the O/D OFF light
in the instrument cluster will illuminate. With
the O/D OFF light illuminated, the transaxle
will operate in first, second and third gears and
will not shift into fourth gear. Operating in D
(O/D OFF) eliminates the excessive shifting
between third and fourth gears that your vehicle
sometimes does when you are traveling through
hilly terrain in D (Overdrive). It also provides
more engine braking than D (Overdrive) for
descending hills or city driving.
[DR07075(ALL)04/95]
To return the transaxle to the normal Overdrive
operation, press the O/D OFF switch again. Use
this switch to select Overdrive or D (O/D OFF)
whenever you drive your vehicle.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

277
reservoir located in the engine compartment. To
locate the reservoir, see the diagram of your
vehicle's engine underEngine Type, in this
chapter.
*
[SV17650(ALL)08/95]
The coolant additives also protect the entire
cooling system from internal passageway
corrosion and these additives lubricate the water
pump. The coolant should be serviced as noted
in theMaintenance Schedule and Recordbooklet.
[SV17700(ALL)04/95]
one third page art:0000305-E
The engine coolant reservoir (3.0L Vulcan shown Ð 3.0L
Duratec similar)
[SV17750(ALL)04/95]
The coolant level in the reservoir should be
maintained within the cold fill range.
[SV17900(ALL)02/95]
There may be a low coolant warning light in the
instrument cluster which will light when the
coolant level is low.
%*
[SV18000(ALL)11/94]
Checking hoses
*
[SV18050(ALL)11/94]
Inspect all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in theMaintenance
Schedule and Recordbooklet. Repair or replace
with Motorcraft hoses or equivalent as necessary.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

301
%*
[SV31200(ALL)03/95]
Power Steering Fluid
*
[SV31300(ALL)01/95]
Check the level of the power steering fluid at
least twice a year (i.e., every Spring and Fall).
%*
[SV31400(ALL)03/95]
Checking and Adding Power Steering
Fluid
*
[SV31500(ALL)02/95]
1. Start the engine and let it run until the
power steering fluid reaches normal
operating temperature. The power steering
fluid will be at the right temperature when
the engine coolant temperature gauge in the
instrument cluster is near the center of the
NORMAL operating temperature range.
*
[SV31600(ALL)01/95]
2. While the engine idles, turn the steering
wheel back and forth several times. Make
sure that the cap assembly is installed at this
time.
*
[SV31700(ALL)01/95]
3. Then turn the engine off.
[SV31800(ALL)04/95]
3.0L Vulcan engine:
%*
[SV31900(ALL)03/94]
4. Check the fluid level on the dipstick (which
is highlighted in yellow in your vehicle). The
fluid level should be between the arrows in
the FULL HOT range, which is marked on
the side of the dipstick, opposite the side
marked FULL COLD. Do not add fluid if the
level is within the FULL HOT range.
*
[SV32100(ALL)07/94]
5. If the power steering fluid is low, add fluid
in small amounts, continuously checking the
level, until you reach the FULL HOT range.
Do not overfill.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

342 [QI02700(S )03/95]
full page art:0001076-EInstrument Cluster
File:fcqis.ex
Update:Tue Aug 8 10:58:48 1995

Index 355
I
Idle
relearning.............. 282
speed................. 66
Ignition
positions of the ignition......... 61
removing the key............ 62
Infant seats (see Safety seats)........ 34
Instrument cluster........... 73,86
standard................ 73
Instrument panel
lighting up panel and interior..... 110
location of components......... 92
Interval wipers............. 117
J
Jack, positioning............ 226
Jump-starting your vehicle
attaching cables............ 219
disconnecting cables.......... 221
K
Keyless entry system
locking and unlocking doors...... 130
programming entry code....... 129
Keys
positions of the ignition......... 61
removing from the ignition....... 62
stuck in lock position.......... 62
L
Lamps
bulb replacement specifications chart . . 323
daytime running light system..... 107
dome lamps............. 111
flashing the lamps.......... 116
hazard flashers............ 118
headlamps.............. 106
File:fcixs.ex
Update:Tue Aug 8 10:58:02 1995