start stop button Mercury Sable 1996 Owner's Manuals

99 [IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
[IP06100(ALL)03/95]
When in AUTO and weather conditions require
cooling, the EATC will use outside air or
recirculated air, depending on the temperature
that is selected.
[IP06125(ALL)04/95]
If unusual conditions exist (i.e., window fogging,
etc.), the six manual override buttons allow you
to select special air discharge locations. The fan
speed button allows you to adjust the fan speed
to suit your needs.
*
[IP06225(ALL)03/95]
Temperature selection
[IP06325(ALL)04/95]
The TEMP button at the upper left of the
Control is for temperature selection. The
aside
of the TEMP button will increase the set
temperature and the
bside of the TEMP button
will lower the set temperature. Pressing the
button and releasing it will change the set
temperature one degree. Holding either side of
the button in will rapidly change the
temperature setting in one degree increments to
either65ÊF (18ÊC) or 85ÊF (29ÊC).Then, the set
temperature will jump 5ÊF(3ÊC) andstop at
either60ÊF (16ÊC)which is maximum cooling or
90ÊF (32ÊC)which is maximum heating.
[IP06525(ALL)02/95]
The average temperature range used is between
68ÊF (20ÊC) and 78ÊF (26ÊC).Changing the
temperature setting by several degrees outside
this range or overriding to 60Ê or90ÊF (16Ê or
32ÊC) asdescribed above will not speed up the
heating or cooling process.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

99 [IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
[IP06100(ALL)03/95]
When in AUTO and weather conditions require
cooling, the EATC will use outside air or
recirculated air, depending on the temperature
that is selected.
[IP06125(ALL)04/95]
If unusual conditions exist (i.e., window fogging,
etc.), the six manual override buttons allow you
to select special air discharge locations. The fan
speed button allows you to adjust the fan speed
to suit your needs.
*
[IP06225(ALL)03/95]
Temperature selection
[IP06325(ALL)04/95]
The TEMP button at the upper left of the
Control is for temperature selection. The
aside
of the TEMP button will increase the set
temperature and the
bside of the TEMP button
will lower the set temperature. Pressing the
button and releasing it will change the set
temperature one degree. Holding either side of
the button in will rapidly change the
temperature setting in one degree increments to
either65ÊF (18ÊC) or 85ÊF (29ÊC).Then, the set
temperature will jump 5ÊF(3ÊC) andstop at
either60ÊF (16ÊC)which is maximum cooling or
90ÊF (32ÊC)which is maximum heating.
[IP06525(ALL)02/95]
The average temperature range used is between
68ÊF (20ÊC) and 78ÊF (26ÊC).Changing the
temperature setting by several degrees outside
this range or overriding to 60Ê or90ÊF (16Ê or
32ÊC) asdescribed above will not speed up the
heating or cooling process.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

178
*
[AS16400(ALL)02/95]
q
Fast forwarding the tape
[AS16525(ALL)04/95]
To fast forward the tape, press the ªFFº
button. The radio will automatically begin
playing until fast forward is manually
stopped (by pressing the ªTAPEº, ªEJº,
ªREWº or ªFFº button) or the end of the
tape is reached. The display will show a
flashing
Xto indicate fast forward.
*
[AS16535(ALL)01/95]
At the end of the tape, the direction
automatically reverses and plays the other
side of the tape.
*
[AS16600(ALL)02/95]
q
Rewinding the tape
[AS16725(ALL)04/95]
To rewind the tape, press the ªREWº button.
The radio will automatically begin playing
until rewind is manually stopped (by
pressing the ªTAPEº, ªEJº, ªREWº or ªFFº
button) or the beginning of the tape is
reached. The display will show a flashing
X
to indicate rewind.
*
[AS17000(ALL)01/95]
q
Using the ªSEEKº function with your cassette
tape player
[AS17125(ALL)04/95]
While in the tape mode, press the right (
a)
side of the ªSEEKº button to seek forward to
the next selection on the tape (display
indicates ªSEEKº). Press the left (
b) side to
seek the previous tape selection.
*
[AS17135(ALL)03/95]
NOTE: If you want to restart a currently
playing tape selection, press the left
(
b) side of the ªSEEKº button after
approximately three seconds into the
current selection.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

184 [AS30301(ALL)04/95]Push the ªCDº button to begin CD play. If the
disc magazine has just been installed, the CD
Changer will automatically begin playing the
first track (selection) of the first disc loaded in
the unit. After that, the CD Changer will start
on the disc and track where it was stopped. The
display will indicate ªCD-##º for disc number,
then display ªTR-##º for track number, then
ªDD-TTº for disc number and track number.
[AS30325(ALL)04/95]
If the CD Changer is empty, ªNOº and ªCDº
will flash in the display and radio play will
continue.
*
[AS30350(ALL)02/95]
How to change the disc being played
[AS30401(ALL)02/95]
When in the CD mode, you can change discs by
pressing the right (
a) side of the ªTUNE/DISCº
button (to select the next disc) or the left (
b)
side of the ªTUNE/DISCº button (to select the
previous disc). Play will begin on the first track
of the selected disc.
*
[AS30450(ALL)02/95]
When either side of the button is pressed and
held, the CD changer will continue
fast-forwarding or reversing through the discs in
the disc magazine. During these functions, the
display will indicate the disc number.
*
[AS30501(ALL)02/95]
How to change the track being played
*
[AS30550(ALL)02/95]
Press the right (
a) side of the ªSEEKº button to
seek forward to the next track of current disc.
After the last track has been completed, the CD
player automatically wraps back to the first track
of the current disc.
*
[AS30601(ALL)02/95]
Press the left (
b) side of the SEEK button to
seek in reverse to the previous track on the
current disc. If a selection has been playing for
three seconds or more and you press the left
(
b) side of the SEEK button, the CD Changer
will replay that selection from the beginning.
File:fcass.ex
Update:Wed Dec 20 09:30:38 1995

201 [DR08050(ALL)11/94]
NOTE: If the O/D OFF indicator light is
flashing on and off repeatedly when
the vehicle is started or does not come
on when the O/D OFF switch is
pushed, it means that there is a
transaxle electronic system malfunction.
You should contact your dealer as soon
as possible or damage to the transaxle
could occur.
*
[DR08075(ALL)02/95]
The transaxle will be in the ªoverdrive onº
mode when the vehicle is started even if the
O/D OFF mode was selected when the vehicle
was last shut off.
*
[DR09025(ALL)01/95]
When to use 2 (Second)
[DR09050(ALL)11/94]
Use Second for start-up on slippery roads or to
give you more engine braking to slow your
vehicle on downgrades.
*
[DR09075(ALL)04/95]
When to use 1 (First)
*
[DR10025(ALL)11/94]
Use 1 (First) when added engine braking is
desired when descending steep hills.
*
[DR10050(ALL)11/94]
The automatic transaxle will shift to the proper
gear to ascend any grade without any need to
shift to 1 (First).
[DR10075(ALL)11/94]
Do not go faster than 38 mph (61 km/h) in this
gear. You can upshift from 1 (First) to D
(Overdrive) at any speed.
*
[DR10125(ALL)01/95]
P (Park)
*
[DR10150(ALL)11/94]
Always come to a complete stop before you shift
into P (Park). Make sure that the gearshift is
securely latched in P (Park). This locks the
transaxle and prevents the front wheels from
rotating.
[DR10160(ALL)04/95]
If your vehicle has a console mounted gearshift,
the gearshift indicator in the cluster is
illuminated in P (Park) only when the gearshift
button is released.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995