light Mercury Villager 1996 s Service Manual

116
[IP13800(ALL)09/93]
Autolamp On/Off Delay System (If equipped)
*
[IP13900(ALL)02/95]
The autolamp sets the headlamps to turn on and off
automatically. You can use the autolamp to:
*
[IP14000(ALL)09/93]
n
turn on the headlamps automatically at night
*
[IP14100(ALL)09/93]
n
turn off the headlamps automatically during daylight
[IP14200(ALL)01/93]
n
keep the headlamps on for approximately three minutes after
you turn the key to OFF.
*
[IP14300(ALL)01/95]
To set the autolamp:
[IP14400(ALL)02/94]1.
Make sure the headlamp control knob is in the OFF position.
If the knob for the headlamps is on, the autolamp system is
canceled.
[IP14500(ALL)04/94]2.
Turn the ignition key to ON to start your vehicle.
[IP14600(ALL)01/93]3.
Use the autolamp thumbwheel to activate the autolamp
feature. It is located to the left of the instrument cluster. The
white mark indicates the approximate center of the
thumbwheel.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

Instrument Panel Controls
119
[IP15700(ALL)09/93]
10-1/2 pica
art:0040075-D
The dome lamp switch positions
[IP15800(ALL)07/93]
Either dome lamp will stay illuminated if the switch is pushed
to the ON position. The dome lamps will stay off if the switch
is pushed to the OFF position. When the switch is positioned to
the door/middle position, the dome lamps will come on when
either of the front doors or the sliding door is opened. The front
dome lamp, footwell lamps, and the sliding door step lamp
have a time delay feature and will gradually dim within about
15 seconds.
[IP15900(ALL)03/95]
The rear dome lamp also illuminates when the liftgate is opened
and goes off when it is closed. However, the rear dome lamp
will not remain lit in the ON position unless the ignition switch
is in the ON position. This feature is intended to help avoid a
run-down battery which can occur when a light is left on
unintentionally.
[IP15950(ALL)02/95]
If the vehicle doors are not fully closed and the interior lamps
remain illuminated, they will eventually turn off automatically
to prevent the battery from becoming discharged. Lamps that
illuminate when the front doors and the sliding door are open
will turn off after approximately 30 minutes. Lamps that are
illuminated when the liftgate is open will turn off after
approximately 60 minutes.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

120
*
[IP16000(ALL)04/95]
Illuminated Entry System (If equipped)
[IP16100(ALL)06/95]
If your vehicle is equipped with this option, the interior
courtesy lamps (footwell, stepwell, and dome lamps) will light
when either of the front doors or the sliding door is opened. If
you have the optional Keyless Entry System the lamps will also
light whenever any keypad or remote keyless entry transmitter
button is pressed. One of the stepwell lamps is located near the
sliding door entrance and there is one on each front door. The
footwell lamps are located below the instrument panel near the
driver's and front passenger's feet. When the liftgate is opened,
the optional liftgate lamp, rear dome lamp and sliding door
stepwell lamp are illuminated.
[IP16200(ALL)01/93]
The lamps that have the time delay feature will automatically
dim until they turn completely off approximately 15 seconds
after the doors are closed. When the key is placed in the
ignition and turned to the ON position, the lamps will turn off.
[IP16300(ALL)09/93]
Overhead Map Lamps (If equipped)
[IP16400(ALL)01/93]
The power sunroof overhead console also contains the overhead
map lamps.
[IP16500(ALL)09/93]
10-1/2 pica
art:0040082-A
The overhead map lamps
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

123
Steering Column Controls
*
[SC00900(ALL)01/95]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[SC01000(ALL)01/93]
Turn Signal Lever
*
[SC01100(ALL)01/95]
You can use the turn signal lever on the left side of the steering
column to:
*
[SC01200(ALL)01/93]
n
operate the turn signals.
*
[SC01300(ALL)01/93]
n
turn the headlamps to high beam.
*
[SC01400(ALL)01/93]
n
flash the headlamps.
*
[SC01500(ALL)01/93]
n
turn the windshield wipers and washer on/off.
*
[SC01600(ALL)01/95]
Turn Signals
[SC01700(ALL)02/95]
Move the lever up to signal a right turn. Move it down to
signal a left turn. The corresponding indicator light in the
instrument cluster will flash.
*
[SC01900(ALL)11/93]
7-1/2 pica art:0040085-D
The turn signal lever
[SC02000(ALL)02/95]
If the turn signal stays on after you turn, move the lever back
to the center (off) position.
[SC02100(ALL)02/95]
For lane changes, move the lever far enough to signal but not to
latch. The lever will return to the off position when you release
it.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

124
*
[SC02200(ALL)05/94]
If the turn indicator light in the instrument panel does not
illuminate or remains on (does not flash) when you signal a
turn, the turn signaling system is malfunctioning. Have this
condition corrected as soon as possible, and use the accepted
hand signals until the turn signal system is repaired.
[SC02225(ALL)01/93]
Cornering Lights
[SC02250(ALL)06/95]
Your vehicle is equipped with special cornering lights designed
to provide additional illumination toward the direction you are
turning. The corresponding light comes on when a turn is
signaled.
*
[SC02300(ALL)05/95]
High Beams and Flashing the Lamps
*
[SC02400(ALL)01/93]
To turn on the high beams, turn the headlamps on and push
the turn signal lever away from you until it latches. When the
high beams are on, the high beam indicator light on the
instrument panel is illuminated.
*
[SC02500(ALL)01/93]
To return to the low beam setting, pull the turn signal lever
toward you until it latches back into the neutral position. The
high beam indicator light turns off.
*
[SC02600(ALL)11/93]
7-1/2 pica art:0040086-D
High beam and flash-to-pass operation
*
[SC02800(ALL)01/93]
To flash the headlamps, pull the turn signal lever toward you
for a moment and then release it. The high beam headlamps
will flash whether the headlamps are on or off.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

Steering Column Controls
125
*
[SC03100(ALL)03/95]
Windshield Wipers and Washer
*
[SC03200(ALL)05/95]
Variable Interval Wipers
[SC03300(ALL)01/93]
Your vehicle has wipers that you can set to operate at varying
intervals. For example, you can set the interval so they wipe
less often in light rain or more often in heavier rain.
*
[SC03400(ALL)09/93]
10-1/2 pica art:0040087-E
Variable interval wiper control
*
[SC03500(ALL)01/93]
To set the interval wipers, rotate the knob at the end of the turn
signal lever to the most effective interval. The farther the knob
is from the OFF position, the faster the wipers move.
[SC03700(ALL)01/93]
To clean the windshield, push in the end of the knob on the
turn signal lever. For a constant spray, push and hold the end
of the knob. If the windshield wipers are off, they automatically
turn on for two wipe cycles after you squirt the washer fluid.
*
[SC03800(ALL)01/93]
Do not try to clean the windshield when the washer fluid
container is empty and never activate the washers for more than
fifteen seconds continuously. This could damage the washer
pump system.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

128
*
[SC05600(ALL)03/91]
Speed Control (If equipped)
[SC05603(ALL)02/95]
The speed control system allows your vehicle to maintain a set
speed above 30 mph (48 km/h) without keeping your foot on
the accelerator pedal.
[SC05605(ALL)01/93]
Avoid using the speed control when driving under the
following conditions:
[SC05610(ALL)07/93]
n
when it is not possible to keep the vehicle at a set speed
[SC05620(ALL)07/93]
n
in heavy traffic or in traffic that varies in speed
[SC05630(ALL)08/93]
n
on winding or hilly roads
[SC05640(ALL)07/93]
n
on slippery roads (rain, snow, ice, etc.)
[SC05650(ALL)09/93]
n
in very windy areas
[SC05800(ALL)09/93]
To activate the speed control, push the main switch (CRUISE
CONT. ON); the switch is located in the group of controls to
the left of the steering wheel. The indicator light on the switch
will come on.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

Steering Column Controls
129
[SC05900(ALL)09/93]
13-1/2 pica
art:0040091-B
Speed control main switch location
[SC06000(ALL)01/93]
Setting the Speed Control
[SC06100(ALL)04/95]
To set the speed control, accelerate your vehicle to the desired
speed (at least 30 mph [48 km/h]), push and release the
COAST/SET button on the left side of the steering wheel. The
CRUISE light in the instrument cluster will come on. Take your
foot off the accelerator pedal. Your vehicle will maintain the set
speed.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

Steering Column Controls
131
%*
[SC06300(ALL)06/95]
Accelerating With the Speed Control Operating
[SC06400(ALL)01/93]
To pass another vehicle while the speed control is activated,
press the accelerator pedal. When you release the pedal, the
vehicle will return to the previously set speed.
[SC06500(ALL)01/93]
Driving Uphill or on a Steep Grade
[SC06600(ALL)01/93]
The vehicle may not maintain the set speed when going up or
down steep hills. If this happens, drive without the speed
control.
[SC06700(ALL)07/93]
When driving uphill, especially with a heavy load, you may
notice your speed decreasing, even if you have the speed
control set. If the speed drops more than 8 mph (13 km/h), it is
normal for the automatic speed control feature to be cancelled.
You may need to help your vehicle maintain the selected speed
by driving without the speed control when driving up steep
grades.
[SC06800(ALL)01/93]
Cancelling the Speed Control
[SC06900(ALL)02/94]
To cancel the preset speed, follow one of these three methods:
[SC07000(ALL)04/95]
n
Push the CANCEL button on the left side of the steering
wheel; the CRUISE light will go out.
[SC07100(ALL)01/93]
n
Tap the brake pedal; the CRUISE light will go out.
[SC07200(ALL)09/93]
n
Press the main OFF switch to the left of the steering wheel.
Both the CRUISE CONT. ON switch indicator and the
CRUISE light in the instrument cluster will go out.
[SC07300(ALL)09/93]
If you unintentionally press the brake pedal while pushing the
RESUME/ACCEL button to reset the cruising speed, press the
OFF switch once and then reactivate the system by pressing the
CRUISE CONT. ON switch.
[SC07400(ALL)01/93]
The speed control will automatically be canceled if the vehicle
slows down below approximately 8 mph (13 km/h).
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996

132
*
[SC07500(ALL)06/95]
Resetting the Speed Control
[SC07600(ALL)02/95]
To reset at a higher speed, use one of the following methods:
[SC07700(ALL)09/93]
n
Press the accelerator pedal. When the speedometer indicates
the desired speed, push and release the COAST/SET button.
[SC07800(ALL)01/93]
n
Push and hold the RESUME/ACCEL button. When the
vehicle attains the speed you desire, release the switch.
[SC07900(ALL)01/93]
n
Push, then quickly release the RESUME/ACCEL button. Each
time you do this, the set speed will increase by about 1 mph
(1.6 km/h).
[SC08100(ALL)02/95]
To reset at a lower speed, use one of the following methods:
[SC08200(ALL)07/93]
n
Lightly tap the brake pedal. When the speedometer indicates
the desired speed, push the COAST/SET button and release
it.
[SC08300(ALL)07/93]
n
Push and hold the COAST/SET button. Release the button
when the vehicle slows down to the desired speed.
[SC08400(ALL)07/93]
n
Push, then quickly release, the COAST/SET button. Each
time you do this, the set speed will decrease by about
1 mph (1.6 km/h).
%*
[SC08500(ALL)06/95]
Resuming a Set Speed
[SC08600(ALL)05/93]
To resume the preset speed, push and release the
RESUME/ACCEL button. The vehicle will resume the last set
speed as long as the vehicle is traveling at a speed over 30 mph
(48 km/h).
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996