light Mercury Villager 1996 s Repair Manual

Adjustable Rear Seating
183
[RR04200(ALL)09/93]
24 pica art:0040147-B
The floor latch levers
[RR04300(ALL)01/93]4.
Place your hand under the seat cushion and tip the front of
the seat upward slightly. Slide the seat rearward to release
the seat from its anchor position.
[RR04400(ALL)01/93]5.
Two people should lift the seat and remove it from the
vehicle.
[RR04450(ALL)06/95]6.
Replace any floor mats that were removed.
File:09vxrrn.ex
Update:Mon Jun 3 14:46:49 1996

184
[RR04500(ALL)01/93]
If you decide to move the three-passenger bench seat forward to
the second row position, passengers riding in the seat will use
the second row safety belts.
[RR04600(ALL)04/95]
Installing the Two-Passenger Bench Seat
[RR04700(ALL)01/93]
To replace the bench seat in its original position:
[RR04800(ALL)06/95]1.
Make sure the area around the floor anchor positions is free
from obstruction.
[RR04900(ALL)01/93]2.
With the seatback folded down, two people should lift the
seat into the vehicle.
[RR05000(ALL)01/93]3.
Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
[RR05100(ALL)01/93]4.
Press down on the front of the seat to secure the front legs
to the two floor latch locks. Place the seatback in the upright
position.
[RR05200(ALL)01/93]5.
Try to move the seat to be sure that it is securely fastened.
[RR05300(ALL)01/93]6.
Always reattach the tongue into the auxiliary buckle
mounted to the side of the seat.
[RR05400(ALL)01/93]
Labels have been provided on the side of the seat to remind
you of important safety precautions.
[RR05700(ALL)01/93]7.
Replace any floor mats that were removed.
[RR05800(ALL)01/93]
RWARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs
from engaging properly.
[RR05900(ALL)01/93]
RWARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
File:09vxrrn.ex
Update:Mon Jun 3 14:46:49 1996

Adjustable Rear Seating
189
[RR07500(ALL)02/94]
17-1/2 pica
art:0040146-B
The removable inside bucket seat
[RR07600(ALL)02/94]3.
Place your hand under the seat cushion and tip the front of
the seat upward slightly. Slide the seat rearward to release
the seat from its anchor position.
[RR07700(ALL)01/93]4.
Two people should lift the seat and remove it from the
vehicle.
[RR07800(ALL)01/93]5.
Replace any floor mats that were removed.
[RR07900(ALL)07/93]
NOTE: The bucket seats are not interchangeable due to the
locations of the floor latch levers. Each seat must be
reinstalled in its original position. In addition, the
seat behind the driver seat only has one arm rest.
File:09vxrrn.ex
Update:Mon Jun 3 14:46:49 1996

190
[RR08000(ALL)01/93]
Installing the Removable Bucket Seats
[RR08100(ALL)01/93]
To position the bucket seats back in their original positions:
[RR08200(ALL)06/95]1.
Make sure the area around the floor anchor positions is free
from obstruction.
[RR08300(ALL)01/93]2.
With the seatback folded down, two people should lift the
seat into the vehicle.
[RR08400(ALL)01/93]3.
Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
[RR08500(ALL)01/93]4.
Press down on the front of the seat to secure the front legs
to the two floor latch locks. Place the seatback in the upright
position.
[RR08600(ALL)01/93]5.
Try to move the seat to be sure that it is securely fastened.
[RR08650(ALL)06/95]6.
Replace any floor mats that were removed.
[RR08700(ALL)01/93]
Labels have been provided on the side of the seats to remind
you of important safety precautions.
[RR09000(ALL)01/93]
RWARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs
from engaging properly.
File:09vxrrn.ex
Update:Mon Jun 3 14:46:49 1996

214
[AS10000(ALL)03/93]
Cassette Tape Player Controls
*
[AS10300(ALL)06/95]
How to insert a tape
[AS10400(ALL)06/95]
Your cassette tape player is equipped with power loading. Once
you insert a tape and push slightly (with theopen edge to the
right), the loading mechanism draws the tape the rest of the
way in and play will begin after a momentary tape tightening
process.
[AS10500(ALL)06/95]
NOTE: A cassette tape can be loaded with the ignition on
whether or not the radio power is on. Inserting a
cassette tape with the radio power off will turn the
audio system on. After the cassette is ejected, the
audio system will turn off. Also, the antenna will be
in the down position whenever the radio is not
playing (i.e., when a cassette or compact disc is
playing or when the radio power is off).
[AS10600(ALL)03/93]
How to locate a desired selection on the tape
[AS10700(ALL)05/94]
There are four ways to locate a desired selection on the tape.
You can use the fast forward, rewind, ªSEEKº or ªSCANº
function. Following are brief descriptions of each.
[AS10800(ALL)05/94]1.
Fast forwarding the tape
[AS10900(ALL)06/95]
To fast forward the tape, press the ªFFº button. The ª
Xº
display blinks while the tape fast forwards. The radio will
automatically begin playing until fast forward is manually
stopped (by pressing ªFFº button) or the end of the tape is
reached. (At the end of the tape, the direction automatically
reverses and plays the other side of the tape.)
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996

216
*
[AS12100(ALL)02/95]
How to eject the tape
[AS12200(ALL)06/95]
To stop the tape and eject the cassette, press the ªEJº button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
*
[AS12300(ALL)06/95]
How to store the tape
[AS12400(ALL)06/95]
Press the ªAM/FMº button to stop the tape player and resume
radio play. Similarly, press the ªCDº button to stop the tape
player and resume CD play. Also, pressing the ªTAPEº button
while the tape is playing pauses tape play.
[AS12450(ALL)06/95]
The ª
Xº symbol displays to indicate there is a tape in the
player. The symbol will be lit until you push the ªTAPEº buton
to resume tape play.
[AS12500(ALL)03/93]
Using the Dolby B noise reduction feature
*
[AS12700(ALL)06/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
[AS12750(ALL)04/95]
Push thekbutton to activate Dolby B noise reduction. When
on, theksymbol will appear in the display.
[AS12800(ALL)03/93]
Tips on caring for your cassette player and tapes
*
[AS12900(ALL)02/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS13000(ALL)02/95]
n
Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS13100(ALL)02/95]
n
Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996

222
[AS32100(ALL)06/95]
How to Take Care of and Clean Your CD Changer and
Discs
[AS32220(ALL)06/95]
To ensure the continued performance of your Ford Compact
Disc Changer, carefully read the following precautions:
*
[AS32230(ALL)04/95]
n
Always handle the disc by its edge. Never touch the playing
surface.
*
[AS32240(ALL)04/95]
n
Before playing, inspect the disc for any contamination. If
needed, clean the disc with an approved disc cleaner, such as
the DiscwasherHCompact Disc Cleaner or the Allsop 3H
Compact Disc Cleaner, by wiping from the center out to the
edges.Do not use a circular motion to clean.
*
[AS32250(ALL)04/95]
n
Do not clean discs with solvents such as benzine, thinner,
commercially available cleaners or antistatic spray intended
for analog records.
*
[AS32260(ALL)04/95]
n
Do not expose the disc to direct sunlight or heat sources
such as defroster and floor heating ducts. Do not leave any
discs in a parked car in direct sunlight where there may be a
considerable rise in temperature or damage may result.
*
[AS32270(ALL)04/95]
n
After playing, store the disc in its case.
[AS32280(ALL)06/95]
n
If a disc has already been inserted, do not try to insert
another disc. Doing so may damage the disc changer.
[AS32290(ALL)06/95]
n
Do not insert anything other than a disc into the disc
changer.
*
[AS32295(ALL)05/95]
RWARNING
The laser beam used in the compact disc player is
harmful to the eyes. Do not attempt to disassemble the
case.
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996

Electronic Sound Systems
227
*
[AS35900(ALL)01/95]
If there is a building or large structure between the antenna and
station, some of the signal ªbendsº around the building, but
certain spots receive almost no signal. Moving out of the
ªshadowº of the structure will allow the station to return to
normal.
[AS36000(ALL)05/95]
This condition exists when the radio waves are reflected off
objects or structures; the reflected signal cancels the normal
signal, causing the antenna to pick up noise and distortion.
Cancellation effects are most prominent in metropolitan areas,
but also can becomes quite severe in hilly terrain and depressed
roadways.
[AS36100(ALL)03/93]
To minimize the effects of these conditions, a stereo/mono
blend circuit has been incorporated into this system. This feature
automatically switches a weak stereo signal to a clearer
monaural signal, which improves the quality of reception.
*
[AS36200(ALL)01/95]
Several sources of static are normal conditions on AM
frequencies. These can be caused by power lines, electric fences,
traffic lights and thunderstorms.
*
[AS36300(ALL)01/95]
Another reception phenomenon isStrong Signal Capture and
Overload. This can occur when listening to a weak station and
when passing another broadcast tower. The close station may
capture the more distant station, although the displayed
frequency does not change. While passing the tower, the station
may switch back and forth a few times before returning to the
original station.
*
[AS36400(ALL)01/95]
When several broadcast towers are present (common in
metropolitan areas) several stations may overload the receiver,
resulting in considerable station changing, mixing and
distortion.
*
[AS36500(ALL)01/95]
Automatic gain control circuitry for both AM and FM bands has
been incorporated into this system to reduce strong signal
capture and overload.
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996

Driving Your Villager
231
*
[DR02700(ALL)01/95]
Driving
[DR03000(ALL)06/95]
When to use D (Overdrive)
[DR03100(ALL)01/93]
Overdrive is the normal driving position. When the gearshift
lever is placed in (D) Overdrive, and the Overdrive Off button
has not been pressed, the vehicle will automatically upshift to
second, third and fourth gears. The transaxle will shift into the
correct gear when the right speed is reached.
%*
[DR03200(ALL)06/95]
When to use D (Drive Ð with the Overdrive Off button
activated)
[DR03300(ALL)06/95]
You will notice that there is only one drive position on your
gearshift selection indicator (instead of Drive and Overdrive).
You will find a button labeled OVERDRIVE OFF/ON located on
the gearshift lever. Push in the button on the end of the lever
and the O/D OFF light in the instrument cluster will illuminate.
With the O/D OFF light illuminated, the transaxle will operate
in first, second and third gears and will not shift into fourth
gear. Operating in Drive (O/D OFF) provides more engine
braking than Overdrive for descending hills, or city driving.
[DR03400(ALL)06/95]
6 pica art:0040164-C
The OVERDRIVE OFF/ON button
*
[DR03500(ALL)09/93]
To return the transaxle to the normal Overdrive operation, press
the OVERDRIVE OFF/ON button again. Use this button to
select Overdrive or Overdrive Off whenever you drive your
vehicle.
[DR03600(ALL)02/95]
NOTE: Overdrive will not engage until the engine has fully
warmed up.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

232
*
[DR03700(ALL)02/95]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
[DR03800(ALL)04/94]
If your vehicle is on an extremely slippery surface, the
Electronic Transaxle Control Module may receive a signal
indicating a rapid increase or decrease in wheel speed. If the
module detects this condition, it will limit the transaxle
operation to Third gear and Reverse. This reduces tire slippage
and protects the transaxle. The transaxle will operate normally
in Reverse, but will lack power during acceleration in Drive. If
this happens, stop your vehicle as soon as possible and turn the
ignition off for 3 seconds. Restart the vehicle. If the condition
still exists, contact your dealer as soon as possible.
*
[DR03900(ALL)04/95]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[DR04000(ALL)06/95]
When to use 2 (Second)
[DR04100(ALL)01/93]
Use Second (2) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second gear operation only. Do not exceed 68 mph
(110 km/h) in this position.
*
[DR04200(ALL)06/95]
When to use 1 (First)
[DR04300(ALL)01/93]
Use First (1) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to Second (2) or Overdrive (D). First (1) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to Second (2), and then
shift back to First (1) after the vehicle decelerates to the proper
speed. Do not exceed 35 mph (56 km/h) in this position.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996