lock Mercury Villager 1997 s Service Manual

Seating and Safety Restraints
163
[SS19890(ALL)01/96]
The automatic locking mode is activated whenever all of the
belt webbing is pulled out of the retractor.
[SS19910(ALL)01/96]
While in this mode, the belt will retract or tighten but cannot be
pulled back out to obtain more length. To disengage the
automatic locking mode, unbuckle the belt and allow the
webbing to retract fully.
%*
[SS19950(ALL)04/96]
Attaching Safety Seats With Tether Straps
*
[SS19970(ALL)04/96]
Some manufacturers make safety seats that include a tether
strap that goes over the back of the vehicle seat and attaches to
an anchoring point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of your child safety
seat for information about ordering a tether strap.
[SS20000(ALL)01/96]
All vehicles built for sale in Canada include tether anchor
hardware for use with Canadian child safety seats. The tether
anchor hardware is located in the tire changing tool kit.
Additional tether anchor hardware can be obtained at no charge
from any Ford or Lincoln-Mercury dealer.
[SS20100(ALL)01/96]
Vehicles built for sale in the USAdo notinclude tether anchor
hardware, but it can be obtained at no charge from any Ford or
Lincoln-Mercury dealer (Part number F3XY-12613D20-A).
[SS20205(ALL)01/96]
The chart below specifies, for each seat type and position, where
the tether strap must be attached to the vehicle and the section
containing the appropriate instructions for tethering.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

Seating and Safety Restraints
167
[SS20760(ALL)01/96]
Tethering to lap/shoulder belt tongue
[SS20770(ALL)05/96]
To attach a tether strap to a lap/shoulder belt:
[SS20780(ALL)01/96]1.
Route the tether strap under the headrest and between the
headrest supports.
[SS20785(ALL)05/96]
13-1/2 pica
art:0040401-A[SS20790(ALL)05/96]2.
Hook the tether strap hook into the large hole at the end of
the tongue of the lap/shoulder belt directly behind the child
seat position.
[SS20800(ALL)01/96]3.
Adjust the tether strap length until the hook is about one
foot behind the seatback.
[SS20815(ALL)05/96]4.
Pull the shoulder belt until all of the belt is fully extended
and a click is heard. At this time the belt is in automatic
locking mode (child restraint mode.)
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

168
[SS20820(ALL)05/96]
13-1/2 pica
art:0040402-A[SS20825(ALL)03/96]5.
Let the retractor wind up the slack from the lap/shoulder
belt. A clicking sound should be heard as the belt retracts,
indicating that the retractor is in automatic locking mode.
Tighten the tether strap to remove any slack.
[SS20835(ALL)05/96]6.
Before placing a child in the child restraint, use force to tilt
the child restraint from side to side and tug it forward to
make sure it is securely held in place.
[SS20837(ALL)05/96]7.
Check that the retractor is in automatic locking mode by
trying to pull more belt out of the retractor. If you cannot
pull any more belt webbing out of the retractor, the belt is in
automatic locking mode.
[SS20838(ALL)03/96]8.
Check to make sure the child restraint is properly secured
prior to each use. If the belt is not locked, repeat steps 4
through 7.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

172
[SS21090(ALL)01/96]
RWARNING
The second row seatback must be fully locked before
operating the child restraint system. Check the position
of the seatback release lever.
[SS21200(ALL)01/96]
17-1/2 pica
art:0040321-A
Second row bench built-in child seats
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

Seating and Safety Restraints
173
[SS21225(ALL)01/96]
Built-In Child Seat Retractors
[SS21250(ALL)01/96]
The retractor will switch from the emergency locking mode to
the automatic locking mode when the right shoulder belt is
pulled all the way out. The retractor will switch back to
emergency locking mode when the belts are unbuckled and the
shoulder belts retract completely.
[SS21275(ALL)01/96]
The automatic locking mode must be used to hold small
children in position, particularly sleeping children and those
who may try to squirm out of the belts. The emergency locking
mode is used while buckling the belts.
*
[SS21300(ALL)01/96]
Always adjust the lap and shoulder harness belts provided with
this child seat snugly around your child.
*
[SS21375(ALL)01/96]
RWARNING
Failure to follow all of the instructions on the use of this
child restraint system can result in your child striking the
vehicle's interior during a sudden stop or crash.
[SS21400(ALL)01/96]
How to Use the Built-In Child Seat
[SS21425(ALL)04/96]
Read the following procedures and all of the labels on the
built-in child seat before using the seat.
*
[SS21450(ALL)01/96]
RWARNING
Never use the Built-In Child Seat as a booster cushion
with the adult safety belts. A child using the adult belts
could slide forward and out from under the safety belts.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

178
[SS21625(ALL)01/96]4.
Place the left shoulder belt harness over the child's left
shoulder. Insert the left shoulder harness tongue into the left
side of the belt buckle. Confirm that the left shoulder
harness tongue indicator is green.
[SS21650(ALL)01/96]
13-1/2 pica
art:0040324-A[SS21675(ALL)01/96]5.
Place the right shoulder belt harness over the child's right
shoulder. Insert the right shoulder harness tongue into the
right side of the belt buckle. Confirm that the right shoulder
harness tongue indicator is green.
[SS21700(ALL)01/96]6.
Fasten the two halves of the chest clip below the child's
shoulders. Adjust the clip to comfortably hold the shoulder
belts in place on the child's chest. Confirm that the chest clip
indicator is green.
[SS21725(ALL)01/96]
NOTE: The chest clip can be easily pulled apart and is
designed to separate during a collision.
[SS21750(ALL)01/96]7.
Pull the right shoulder belt fully out to put the retractor into
the locking mode. At this time, the shoulder belts are in an
automatic locking mode. Allow the safety belts to tighten
snugly against the child's shoulders. The belt will
automatically lock and cannot be pulled out.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

180
[SS21925(ALL)01/96]4.
Confirm that the shoulder belts are fully retracted and
resting inside the built-in child seat recess. It is unnecessary
to reconnect the shoulder harness and belt buckle prior to
storing the built-in child seat.
[SS21950(ALL)05/96]5.
While holding the tab, rotate the cushion upward until it fits
flush with the second row seatback pad.
[SS21975(ALL)01/96]
13-1/2 pica
art:0040326-A[SS22000(ALL)01/96]6.
Confirm that the built-in child seat is locked in the stowed
position by grasping the safety seat cushion and attempting
to lower it without pulling the cushion release strap.
[SS22025(ALL)01/96]7.
If the built-in child seat is not locked in the stowed position,
repeat steps 4 through 6.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

190
[RR04500(ALL)01/93]
If you decide to move the three-passenger bench seat forward to
the second row position, passengers riding in the seat will use
the second row safety belts.
[RR04600(ALL)04/95]
Installing the Two-Passenger Bench Seat
[RR04700(ALL)01/93]
To replace the bench seat in its original position:
[RR04800(ALL)07/95]1.
Make sure the area around the floor anchor positions is free
from obstruction.
[RR04900(ALL)01/93]2.
With the seatback folded down, two people should lift the
seat into the vehicle.
[RR05000(ALL)01/93]3.
Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
[RR05100(ALL)01/93]4.
Press down on the front of the seat to secure the front legs
to the two floor latch locks. Place the seatback in the upright
position.
[RR05200(ALL)01/93]5.
Try to move the seat to be sure that it is securely fastened.
[RR05300(ALL)05/96]6.
Always reattach the tongue into the auxiliary buckle
mounted to the sliding door side of the seat.
[RR05400(ALL)01/93]
Labels have been provided on the side of the seat to remind
you of important safety precautions.
[RR05700(ALL)01/93]7.
Replace any floor mats that were removed.
[RR05800(ALL)01/93]
RWARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs
from engaging properly.
File:07vxrrn.ex
Update:Thu May 30 09:53:21 1996

196
[RR08000(ALL)01/93]
Installing the Removable Bucket Seats
[RR08100(ALL)01/93]
To position the bucket seats back in their original positions:
[RR08200(ALL)07/95]1.
Make sure the area around the floor anchor positions is free
from obstruction.
[RR08300(ALL)01/93]2.
With the seatback folded down, two people should lift the
seat into the vehicle.
[RR08400(ALL)01/93]3.
Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
[RR08500(ALL)01/93]4.
Press down on the front of the seat to secure the front legs
to the two floor latch locks. Place the seatback in the upright
position.
[RR08600(ALL)01/93]5.
Try to move the seat to be sure that it is securely fastened.
[RR08650(ALL)06/95]6.
Replace any floor mats that were removed.
[RR08700(ALL)01/93]
Labels have been provided on the side of the seats to remind
you of important safety precautions.
[RR09000(ALL)01/93]
RWARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs
from engaging properly.
[RR09100(ALL)01/93]
RWARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
File:07vxrrn.ex
Update:Thu May 30 09:53:21 1996

202
[RR10700(ALL)01/93]
RWARNING
After moving the third-row seat, be sure to latch the seat
in a passenger seating position. Improper location of the
seat will prevent correct use of the safety belts and will
increase the risk of severe injury in an accident. After
sliding the seat, check that both sides of the seat are
locked securely by attempting to move each side of the
seat forward and backward. This must be done before
the vehicle is put into motion in order to prevent
unintended movement of the seat and potential passenger
injuries.
[RR10800(ALL)09/95]
NOTE: Before rearranging the seats, remove any floor mats
that might be in the way.
[RR10900(ALL)01/93]
The three-passenger seat can be stored behind the second-row
seat(s) to provide extra cargo space in the rear of the vehicle.
[RR11000(ALL)01/93]
With the second row seat(s) removed, the three-passenger bench
seat can be moved all the way forward, just behind the front
seats for more room in the cargo area.
[RR11100(ALL)01/93]
To move the seat all the way forward:
[RR11200(ALL)01/93]1.
Lift up on the seat cushion release lever and fold up the seat
cushion.
File:07vxrrn.ex
Update:Thu May 30 09:53:21 1996