headlamp Mercury Villager 1998 s User Guide

Using the Panic Alarm
If you are near your vehicle and feel threatened, you may
activate the alarm to call attention to it.
To activate the PANIC alarm, push and hold the PANIC button
on the remote for longer than 1.5 seconds. The horn will sound and
the headlamps and tail lights will flash for thirty (30) seconds.
To turn off the alarm, press the LOCK or UNLOCK buttons or hold
the PANIC button down for longer than 1.5 seconds.
Replacing the Batteries
The remote entry transmitter is powered by two coin type Sanyo
CR2016 3 volt batteries (included). If you notice a significant
decrease in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies, watch
stores or at your Ford or Lincoln-Mercury dealer.
NOTE: The operating range of the remote entry system can
also be affected by weather conditions (such as very
cold temperatures) or structures around the vehicle
(buildings, other vehicles, radio and TV towers,
etc.). Typical operating range will allow you to be up to
49 feet (15 meters) away from your vehicle.
Replacing the batteries
11 4

ID Code Programming Procedure
NOTE: All transmitters must be programmed (or
reprogrammed) at the same time. If the programming
mode is entered and the transmitters are not programmed
(or reprogrammed) at the same time, they will not
operate with the system.
1. Enter vehicle and close and lock all doors.
2. Insert and remove key from ignition six times within ten (10)
seconds. The instrument panel lights will flash twice.
3. Turn ignition key to the ACC position.
4. Press the LOCK button on the remote transmitter once.
5. To enter additional remote controllers (including the original),
unlock, then lock the driver door using the power door lock
switch.
6. Press the LOCK button on a new remote transmitter. The
instrument panel lights will flash twice, indicating code is
entered.
7. Repeat steps 5 and 6 as needed (up to four remote transmitters
may be programmed).
Anti-Theft System (If equipped)
This system helps protect your vehicle against break-ins or theft
by monitoring all doors, the hood and the liftgate lock
cylinder.
When an unauthorized entry occurs, the system triggers and will:
mflash the headlamps and hazard lamps
mhonk the horn
mdisable the starting circuit to prevent the vehicle from being
started
11 6

Fuel-Injected Engines
When starting a fuel-injected engine,the most important thing to
remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your Engine
in this chapter for details about when to use the accelerator
while you start your vehicle.
Starting Your Vehicle
Preparing to Start Your Vehicle
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
Before you start your vehicle, always:
1. Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
2. Make sure the headlamps and other accessories are turned off
when starting.
3. Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
4. Observe the warning lights on the instrument cluster to make
sure they work. Refer to theInstrumentationchapter.
Starting Your Engine
To start your engine:
1. Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
Starting
207

Lights and Bulb Replacement
It is a good idea to check the operation of the following lights
frequently:
mheadlamps
mhigh-mount brakelamp
mtail lamps
mbrakelamps
mcornering lamps
mhazard flasher
mturn signals
mlicense plate lamps
The alignment of your headlamps should be checked if:
moncoming motorists frequently signal you to turn off your
vehicle's high beams when you do not have the high
beams on
mthe headlamps do not seem to give you enough light to see
clearly at night
mthe headlamp beams are not pointed slightly down and to the
right
Headlamp Bulb
The headlamps on your vehicle use replaceable bulbs. When the
lamp burns out, simply replace the bulb, rather than the
whole lamp.
316

WARNING
Handle a halogen headlamp bulb carefully and keep out
of children's reach. Grasp the bulb only by its plastic
base and do not touch the glass. The oil from your hand
could cause the bulb to break the next time the headlamps
are operated.
Do not remove the burned out bulb unless you can immediately
replace it with a new one. If a bulb is removed for an
extended period of time, contaminants may enter the headlamp
and affect its performance.
Removing the headlamp bulb
1. Make sure that the engine is off and the headlamp switch on
the instrument panel is in the OFF position.
2. Remove the electrical connector from the bulb by pulling the
connector away from the bulb assembly.
The headlamp bulb assembly
Maintenance and Care
317

3. Remove the bulb retaining ring by turning it counterclockwise
1/8 of a turn to free it from the socket. Then slide the ring off
the plastic base.Keep the ring.You must use it again to
hold the new bulb in place.
4. Carefully remove the bulb assembly from its socket by
gently pulling it rearward without turning.
5. Do not touch the bulb with your skin or you could shatter the
bulb. Always grasp the bulb assembly from the plastic base.
6. Be sure that you have the proper replacement bulb ready before
you discard the burned out bulb.
Removing the headlamp bulb retaining ring
318

Installing the headlamp bulb
1. With the flat side of the bulb's plastic base facing upward,
insert the glass end of the bulb into the socket. You may
need to turn the bulb left or right to line up the grooves in the
plastic base with the tabs in the socket. When the grooves
are aligned, push the bulb into the socket until the plastic base
contacts the rear of the socket. Do not touch the glass with
your fingers.
2. Slip the retaining ring over the plastic base until it contacts the
rear of the socket. Lock the ring into the socket by rotating it
until you feel a ªstop.º
3. Push the electrical connector into the rear of the plastic base
until it snaps, locking it into place.
Headlamp bulb replacement
Maintenance and Care
319

4. Turn the headlamps on and make sure that they work
properly. If the headlamp was correctly aligned before you
changed bulbs, you should not need to align it again.
Replacing the Bulbs
There are several different types of replacement bulbs for your
vehicle. The following illustration indicates the proper method of
removal and installation for each bulb.
The illustrations in this section will provide you with reference for
changing many of the bulbs on your vehicle.
The replacement bulbs
320

servicing......................217, 282
stopping distances....................218
trailer..........................235
when storing your vehicle................335
Brights (high beams).....................17
Bulbs, replacing.......................316
halogen.........................316
headlamps........................316
specifications.......................322
C
Canada, customer assistance................352
Canadian Motor Vehicle Arbitration Plan (CAMVAP)....352
Car seats for children (see Child safety seats)........153
Carbon monoxide in exhaust................212
Cargonet ..........................111
Catalytic converter.....................313
Chains, tires........................305
Changing a tire.......................254
Charging system warning light................14
Child safety restraints....................151
child safety belts.....................166
child safety seats.....................153
Child safety seats......................153
and air bags.......................153
attaching with tether straps...............160
automatic locking mode (retractor)..........136, 153
in front seat.......................153
in rear outboard seat...................153
in rear seat........................153
tether anchorage hardware................160
Childproof locks......................100
Index
375

Chime
headlamps on.......................18
safety belt.........................11
Circuit breakers
checking and replacing..................252
see also fuses......................243
Cleaning your vehicle....................329
chrome and aluminum parts...............330
engine compartment...................331
exterior.........................329
exterior lamps......................330
fabric..........................332
headlamps........................330
instrument panel.....................330
instrument panel lens..................332
interior..........................332
plastic parts.......................330
polishing.........................329
rustproofing.......................330
safety belts........................332
tail lamps........................330
upholstery and interior trim...............332
washing.........................329
waxing..........................329
wheels..........................330
Climate control system
air conditioning......................56
heating..........................56
Clock............................40
Clutch
fluid reservoir......................282
Cold engine starting....................208
Combination lap and shoulder belts..........129, 131
376