battery Mercury Villager 1998 Owner's Manuals

WARNING
Under engine misfire conditions, excessive exhaust
temperatures could damage the catalytic converter, the
fuel system, interior floor coverings or other vehicle
components, possibly causing a fire.
Charging System Light
This light indicates that your battery is not being charged and
that you need to have the electrical system checked.
This light illuminates every time you turn your ignition key to the
ON or START position. The light should go off when the
engine starts and the alternator begins to charge.
If the light stays on or illuminates when the engine is running,
have the electrical system checked as soon as possible.
Engine Oil Pressure Warning Light
The oil pressure light is represented by an oil can symbol. It
indicates the engine's oil pressure, not oil level. However, if your
engine's oil level is low, it could affect the oil pressure. The oil
pressure light will flash if the oil pressure drops below the normal
operating level. When you turn the key to the ON position, the
light will illuminate.
Charging system light
14

Setting the station memory preset buttons
Your radio is equipped with 6 station memory buttons. These
buttons can be used to select up to 6 preset AM stations and 12 FM
stations (6 in FM1 and 6 in FM2). Follow the easy steps below
to set these buttons to the desired frequencies:
1. Select a band, then select a frequency.
2. Press one of the memory preset buttons and hold the button
until the sound returns. That station is now held in memory
on that button.
3. Follow the two steps above for each station memory preset
button you want to set.
NOTE: If the vehicle's battery is disconnected, the Station
Memory Preset buttons will need to be reset.
mUsing the Automatic Memory Store feature (Supersound only)
Activate Auto Memory Store by pushing the ªAUTO SETº
button once. Your radio will set the first six strong stations of
the band you are in (AM, FM1 or FM2) into the memory
buttons. The display will show ªAUTO,º then run through the
frequencies, stopping momentarily on the stations being set
into the memory buttons. The radio is now in the ªAUTOº mode
and this display will show ªAUTOº each time a preset
selected by ªAUTO SETº is activated.
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your existing
memory presets, which is especially helpful while traveling.
Your radio will automatically set your memory buttons to the
strong local stations so you don't have to continually
manually tune to existing stations.
Electronic Sound Systems
35

Interior Lamps
The front dome lamp is located overhead between the driver and
front passenger seats. However, if your vehicle is equipped
with a power sunroof, the dome lamp is located behind the driver's
seat.
The rear dome lamp is located overhead near the rear seating
positions.
Either dome lamp will stay illuminated if the switch is pushed
to the ON position. The dome lamps will stay off if the switch is
pushed to the OFF position. When the switch is positioned to
the door/middle position, the dome lamps will come on when
either of the front doors or the sliding door is opened. The
front dome lamp, footwell lamps, and the sliding door step lamp
have a time delay feature and will gradually dim within about
15 seconds.
The rear dome lamp also illuminates when the liftgate is opened
and goes off when it is closed. However, the rear dome lamp
will not remain lit in the ON position unless the ignition switch
is in the ON position. This feature is intended to help avoid
a run-down battery which can occur when a light is left on
unintentionally.
The dome lamp switch positions
82

If the vehicle doors are not fully closed and the interior lamps
remain illuminated, they will eventually turn off automatically to
prevent the battery from becoming discharged. Lamps that
illuminate when the front doors and the sliding door are open
will turn off after approximately 30 minutes. Lamps that are
illuminated when the liftgate is open will turn off after
approximately 60 minutes.
Illuminated Entry System (If equipped)
If your vehicle is equipped with this option, the interior courtesy
lamps (footwell, stepwell, and dome lamps) will light when
either of the front doors or the sliding door is open. If you have
the optional Keyless Entry System the lamps will also light
whenever the remote keyless entry transmitter button is pressed.
There are stepwell lamps located near the sliding door
entrance and one on each front door. The footwell lamps are
located below the instrument panel near the driver 's and front
passenger 's feet. When the liftgate is opened, the optional liftgate
lamp, rear dome lamp and sliding door stepwell lamp will
illuminate.
The lamps that have the delay feature will automatically dim
until they turn completely off approximately 15 seconds after the
doors are closed. When the key is placed in the ignition and
turned to the ON position, the lamps will turn off.
Controls and Features
83

Remove the two batteries by snapping open the lid of the remote
transmitter. The transmitter can be snapped apart by twisting
a thin coin between the two halves of the transmitter. Replace the
batteries with new ones as shown in the above illustration.
Close the lid securely. Press both the LOCK and the UNLOCK
button two or three times to test the remote transmitter operation.
If the batteries are removed for any reason other than
replacement, repeat the steps inReplacing the batteriesto test your
remote transmitter(s).
mAn improperly disposed battery can hurt the environment.
Always confirm local regulations for battery disposal.
mThe remote transmitter is waterproof; however, if it does get
wet, immediately wipe it completely dry.
mThe operational range of the remote transmitter extends to
approximately 49 feet (15 meters) from the vehicle. This
range may vary with conditions.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
Replacement/Additional Transmitters
In the event a transmitter is lost or an additional remote
transmitter needs to be set, you must change the ID code. Follow
the steps below to change the ID code of your system, or
return the remaining transmitter(s) to your dealer for
reprogramming of your remote entry system. This is necessary to
prevent unauthorized use of the lost transmitter.
Controls and Features
11 5

Trailer Tow Module (If equipped)
The trailer tow module on your vehicle (if equipped) allows
turn/stop lamp control on a trailer being towed by your vehicle.
The trailer tow package includes:
mtrailer tow module which is protected by the vehicle stop
lamp fuse
mone SAE J1239 specified connector
mone extension harness within the rear bumper
mheavy duty battery
mfull size spare
If you need further assistance in wiring a trailer to your vehicle,
contact your Ford or Lincoln-Mercury dealer.
Driving While You Tow
Be especially careful when driving while you tow a trailer. Never
drive faster than 45 mph (70 km/h) when you tow in hilly
country on hot days. Also, anticipate stops so that you can brake
gradually.
If you use the speed control while you are towing on very long,
steep grades, the speed control may shut off automatically.
This is caused by the decrease of vehicle speed 5 mph (8 km/h)
lower than set speed.
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift into 2
(Second) or 1 (First) gear.
Servicing Your Vehicle If You Tow
If you tow a trailer for a long distance, your vehicle will need to
be serviced more frequently than usual. See theMaintenance
Schedulebooklet in the Owner's portfolio.
236

Hazard Flasher Switch
The hazard flasher is used to alert other drivers to hazardous
situations.
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these lamps
will flash on and off. The turn signal indicators cannot be used
when the hazard lamps are flashing. Operation of the hazard
flashers does not affect operation of the brakelamps.
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the
battery excessively. If the flashers run for longer than two hours
or if your battery is not fully charged, your battery may be
drained to the point where the vehicle will not start.
The hazard flasher switch is located on the instrument panel to
the right of the instrument cluster.
Roadside Emergencies
241

Jump-Starting Your Battery
Your vehicle's battery may discharge if you leave the lights or
any electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start from a booster
battery to start your vehicle.
WARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
WARNING
To protect yourself when charging a battery, always shield
your face and eyes. Make sure that you can breathe
fresh air.
WARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
WARNING
Batteries contain sulfuric acid which burns skin, eyes, and
clothing.
If the acid touches someone's skin, eyes, or clothing, immediately
flush the area with water for at least 15 minutes. If someone
swallows the acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or vegetable oil. Call a
doctor immediately.
268

To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your vehicle
to jump-start and connecting the jumper cables in the order
they are given. If in doubt, call for road service.
Preparing Your Vehicle
1. Your vehicle has a 12-volt starting system, so you need to use
a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you connect
them to a 24-volt power supply (either two 12-volt batteries
in series or a 24-volt generator set).
2. Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
3. Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set the
parking brake on both vehicles and stay clear of the engine
cooling fan and other moving parts.
4. Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
5. Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
Roadside Emergencies
269

Connecting the jumper cables
1. Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use the
same cable for both positive terminals.) Most jumper cables
have a red cable and a black cable. The red cable is generally
used for the positive terminals and the black for the
negative cable of the booster battery and ground on the engine
of the disabled vehicle.
2. Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
3. Connect one end of the second cable to the negative (±)
terminal of the booster battery Ð NOT to the discharged battery.
4. Connect the other end of the second cable to a good metallic
surface on the engine or frame of the disabled vehicle.
WARNING
Do not connect the end of the second cable to the negative
(±) terminal of the battery to be jumped. A spark may
cause an explosion of the gases that surround the battery.
270