engine overheat MINI 3 door 2013 Owner's Manual
[x] Cancel search | Manufacturer: MINI, Model Year: 2013, Model line: 3 door, Model: MINI 3 door 2013Pages: 233, PDF Size: 17.19 MB
Page 49 of 233
Radio ready state
Activate radio ready state:▷When the engine is running: press the Start/
Stop button.
Some electronic systems/power consumers re‐
main ready for operation.
Radio ready state switches off automatically:
▷After approx. 8 minutes.▷When the vehicle is locked using the central
locking system.▷Shortly before the battery is discharged
completely, so that the engine can still be
started.
Starting the engine
General information Enclosed areas
Do not let the engine run in enclosed
areas, since breathing in exhaust fumes may
lead to loss of consciousness and death. The
exhaust gases contain carbon monoxide, an
odorless and colorless, but highly toxic gas. ◀
Unattended vehicle
Do not leave the vehicle unattended with
the engine running; doing so poses a risk of
danger.
Before leaving the vehicle with the engine run‐
ning, set the parking brake and place the trans‐
mission in selector lever position P or neutral to
prevent the vehicle from moving. ◀
Repeated starting in quick succession
Avoid repeated unsuccessful attempts to
start the vehicle or starting the vehicle several
times in quick succession. Otherwise, the fuel is
not burned or is inadequately burned, posing a
risk of overheating and damage to the catalytic
converter. ◀
Do not wait for the engine to warm-up while
the vehicle remains stationary. Start driving at
moderate engine speeds.
Diesel engine If the engine is cold and temperatures are be‐
low approx. 32 ℉/0 ℃, the start process may
be delayed somewhat due to automatic pre‐
heating.
A Check Control message is displayed.
Automatic transmission
Starting the engine1.Depress the brake pedal.2.Engage selector lever position P or N.3.Press the Start/Stop button.
The ignition is activated automatically for a cer‐
tain time and is stopped as soon as the engine
starts.
Manual transmission
Starting the engine
1.Depress the brake pedal.2.Press on the clutch pedal and shift to neu‐
tral.3.Press the Start/Stop button.
The ignition is activated automatically for a cer‐
tain time and is stopped as soon as the engine
starts.
Engine stop
General information Take the remote control with you
Take the remote control with you when
leaving the vehicle so that children, for exam‐
ple, cannot start the engine. ◀
Seite 45DrivingControls45
Online Edition for Part no. 01 40 2 925 116 - X/13
Page 130 of 233
Objects in the area around the pedalsNo objects in the area around the pedals
Keep floor mats, carpets, and any other
objects out of the area of motion of the pedals;
otherwise, the function of the pedals could be
impeded while driving and create the risk of an
accident.
Do not place additional floor mats over existing
mats or other objects.
Only use floor mats that have been approved for the vehicle and can be properly fixed in
place.
Ensure that the floor mats are securely fastened
again after they were removed for cleaning, for
example. ◀
Driving in wet conditions When roads are wet or there is heavy rain,
briefly exert gentle pressure on the brake pedal
every few miles.
Ensure that this action does not endanger other
road users.
The heat generated in this process helps dry
the brake discs and pads.
In this way braking efficiency will be available
when you need it.
HillsDrive long or steep downhill gradients in the
gear in which the least braking is required. Oth‐
erwise, the brake system may overheat, result‐
ing in a reduction in the brake system effi‐
ciency.
You can increase the engine's braking effect by
shifting down, going all the way to first gear, if
necessary.
Avoid load on the brakes
Avoid placing excessive load on the brake
system. Light but consistent brake pressure can
lead to high temperatures, brake wear and
possibly even brake failure. ◀Do not drive in neutral
Do not drive in neutral or with the engine
stopped, as doing so disables engine braking.
In addition, steering and brake assist are un‐
available with the engine stopped. ◀
Brake disc corrosion Corrosion on the brake discs and contamina‐
tion on the brake pads are furthered by:▷Low mileage.▷Extended periods when the vehicle is not
used at all.▷Infrequent use of the brakes.
Corrosion occurs when the minimum pressure
that must be exerted by the pads during brake
applications to clean the discs is not reached.
Should corrosion form on the brake discs, the
brakes will tend to respond with a pulsating ef‐
fect that generally cannot be corrected.
Condensation under the parked vehicle
When using the automatic climate control, con‐
densation water develops that exits under‐
neath the vehicle.
Traces of water under the vehicle like this are
normal.
Ground clearance Limited ground clearance
Observe the limited ground clearance of
the vehicle, e. g. while entering underground
parking garages or when driving over obsta‐
cles. Otherwise, damages to the vehicle may
result. ◀
Seite 126Driving tipsThings to remember when driving126
Online Edition for Part no. 01 40 2 925 116 - X/13
Page 179 of 233
4.Slide the sealing bottle upright into the
holder on the compressor housing, ensur‐
ing that it engages audibly.5.Screw the connection hose onto the valve
of the defective wheel.6.With the compressor switched off, insert
the plug into a power socket inside the ve‐
hicle.7.With the ignition turned on or the engine
running, switch on the compressor.
Let the compressor run for approx. 3 to 8 mi‐
nutes to fill the tire with sealant and achieve a
tire inflation pressure of approx. 2.5 bar.
While the tire is being filled with sealant, the in‐
flation pressure may sporadically reach approx.
5 bar. Do not switch off the compressor in this
phase.
Enclosed areas
Do not let the engine run in enclosed
areas, since breathing in exhaust fumes may
lead to loss of consciousness and death. The
exhaust gases contain carbon monoxide, an
odorless and colorless, but highly toxic gas. ◀
Switch off the compressor after 10 mi‐
nutes
Do not allow the compressor to run longer than
10 minutes; otherwise, the device will overheat
and may be damaged. ◀
If a tire pressure of 2 bar is not reached:
1.Switch off the compressor.2.Unscrew the filling hose from the wheel.3.Drive forward and back to distribute the
sealant in the tire.4.Inflate the tire again using the compressor.
If an inflation pressure of 2 bar cannot be
reached, contact your service center.Seite 175Wheels and tiresMobility175
Online Edition for Part no. 01 40 2 925 116 - X/13
Page 229 of 233
Octane rating, refer to Gaso‐line quality 164
Odometer 59
Oil 180
Oil, adding 181
Oil additives 181
Oil change 182
Oil change interval, service re‐ quirements 60
Oil filler neck 181
Oil types, alternative 182
Oil types, approved 182
Old batteries, disposal 197
Onboard Diagnostics OBD 184
Onboard vehicle tool kit 186
Opening/closing via door lock 23
Opening/closing with remote control 22
Optional equipment, standard equipment 6
Outside air, refer to Automatic recirculated-air control 108
Overheating of engine, refer to Coolant temperature 59
P Paint, vehicle 204
Panoramic glass sunroof 30
Parallel parking assistant 100
Park Distance Control PDC 98
Parked vehicle, condensa‐ tion 126
Parking aid, refer to PDC 98
Parking assistant 100
Parking brake 48
Parking lamps 66
Particulate filter 125
Passenger side mirror, tilting downward 37
PDC Park Distance Control 98
Pedestrian warning with city braking function 83
Performance Control 87 Personal Profile 21
Phone 152
Pinch protection system, glass sunroof 31
Pinch protection system, win‐ dows 29
Plastic, care 205
Power failure 196
Power windows 29
Pressure, tire air pressure 166
Pressure warning, tires 77
Profile, refer to Personal Pro‐ file 21
Protective function, glass sun‐ roof 31
Protective function, win‐ dows 29
R Radiator fluid 183
Radio, AM/FM stations 139
Radio, control ele‐ ments 139, 145
Radio, FM/AM 139
Radio, muting 139
Radio-operated key, refer to Remote control 20
Radio, overview 139, 145
Radio ready state 45
Radio, satellite radio 143
Radio, save stations 141
Radio, traffic bulletins 142
Rain sensor 50
Rear fog lamps 69
Rear lamps 190
Rear luggage rack 129
Rearview mirror 37
Rear window de‐ froster 105, 108
Recirculated-air filter 109
Recirculated-air mode 105, 108
Recommended tire brands 172
Refueling 162 Remaining range 60
Remote control/key 20
Remote control, blocking 21
Remote control, malfunc‐ tion 23
Remote control, replacing the battery 20
Remote control, univer‐ sal 110
Replacement fuse 197
Replacing parts 186
Replacing the battery, remote control 20
Replacing wheels/tires 171
Reporting safety defects 9
RES button 92
Reserve warning, refer to Range 60
Resetting the tone set‐ tings 138
Reset, Tire Pressure Monitor TPM 75
Retaining straps, securing cargo 128
Retreaded tires 172
Right-hand traffic, lamp set‐ ting 69
Roadside parking lamps 66
RON gasoline quality 164
Roof load capacity 210
Roof-mounted luggage rack 128
Rope for tow-starting/ towing 201
RSC Run Flat System Compo‐ nent, refer to Run-flat
tires 173
Rubber components, care 205
Run-flat tires 173
S
Safe braking 125
Safety 6 Seite 225Everything from A to ZReference225
Online Edition for Part no. 01 40 2 925 116 - X/13