service MINI Coupe 2012 Owner's Guide

CareMOBILITY
161
Care
Vehicle equipment
In this chapter, all production, country, and
optional equipment that is offered in the model
range is described. Equipment is also described
that is not available because of, for example,
selected options or count ry version. This also
applies to safety related functions and systems.
Car-care products
Regular cleaning and care helps to maintain the
value of your MINI.
The manufacturer of your MINI recommends
using manufacturer-approved products to clean
and care for your vehicle.
Your MINI dealer would be pleased to advise
you on cleaning and care products and services
for your MINI.
The ingredients of original MINI Care
Products have been tested, and the
products have been tested in the laboratory
and in practice. They offer optimum care and
protection for your vehicle. <
Do not use any cleansers containing
alcohol or solvents as these may cause
damage. <
Cleaning agents may contain hazardous
or health-damaging substances. Follow
the warning and hazard instructions on the
packaging. For interior cleaning, always open
the doors or windows of the vehicle.
Do not use any products that are not intended
for cleaning the vehicle. <
External care
Washing your vehicle
Especially during the winter months the
vehicle should be frequently washed. Dirt
and road salt can damage the vehicle.<
After washing the vehicle, apply the
brakes briefly to dry them; otherwise,
water can reduce braking efficiency over the
short term and the brake rotors can corrode. <
Car washes
Preference should be given to cloth car washes.
Do not use automatic high-pressure car
washes; otherwise, water may drip into
the vehicle around the windows. <
Before driving into the car wash, check if the
system is suitable for your MINI. Observe the
following points:
> Vehicle dimensions, page 197.
> If necessary: fold in the outside mirrors,
page 49.
> Maximum permissible tire width.
Avoid car washes with tracks higher than
4 in/10 cm; otherwise, the chassis could
be damaged. <
Preparations for driving into the car wash:
> Unscrew the rod antenna.
> MINI Coupe, MINI Roadster: retract spoiler.
> Deactivate the rain sensor to prevent
unintentional wiping.
> Remove additional attachments, e.g.
spoilers or telephone antennas, if there is
a possibility that they could be damaged.
> Insert the remote control into the ignition
lock.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

MOBILITYCare
162
Automatic transmission
Before driving into the car wash, make sure that
the vehicle can roll:
1.Place the remote control, even with Comfort
Access, in the ignition lock.
2. Move the selector lever to position N.
3. Release the parking brake.
4. Switch off the engine.
5. Insert the remote control in the ignition lock
so that the vehicle can roll.
Steam jets/high-pressure washers
When using steam jets or high-pressure
washers, make sure that you maintain
sufficient distance from the vehicle and do not
exceed a maximum temperature of 140 7/
60 6 .
If the distance is too close, the pressure too high,
or the temperature too high, parts of the vehicle
can be damaged, or water can penetrate.
Observe the operating instructions for high-
pressure washers. <
Do not spray sensors, such as the Park
Distance Control, with high-pressure
washers for a long time or at a distance of less
than 1 ft/30 cm. <
Manual washing
Use a great deal of water and, if necessary, car
shampoo when washing your car by hand. Clean
the vehicle with a sponge or a washing brush
applying a slight amount of pressure.
Before cleaning the windshield, deacti-
vate the rain sensor or turn off the ignition
to prevent unintentional wiping. <
Observe local regulations regarding
washing vehicles by hand. <
Headlamps
Do not wipe dry and do not use abrasive or
corrosive cleaning agents. Remove dirt and
contamination, such as in sects, by soaking with
shampoo and then washing with plenty of
water. Do not remove accumulated ice and snow with
an ice scraper; use window deicers instead.
Windows
Clean the outside and inside of the windows and
mirrors with a window cleaner.
Do not clean the mirrors with cleaners
containing quartz. <
Wiper blades
Clean with soapy water and change regularly to
prevent the formation of streaks.
Wax, preservatives and dirt on the
windows cause streaks when the wind-
shield wipers are on, and can cause premature
wear of the wiper blades and interfere with the
rain sensor. <
Care of the convertible top
The appearance and service life of the conver-
tible top largely depends on its proper care and
operation.
Please follow these instructions:
>Never attempt to fold and stow the conver-
tible top in the convertible compartment
when the top is wet or frozen. Otherwise,
water stains, mildew, and chafe marks may
occur.
> If water spots occur on the inside headliner
despite precautions, remove them using a
microfiber cloth and interior cleaner.
> If the vehicle is parked in an enclosed area
for a longer period of time, make sure that
there is sufficient ventilation.
> Remove any bird droppings immediately,
since they have corrosive properties which
will corrode the conver tible top and damage
the rubber seals.
When attempting to remove stains from
the convertible top, do not use spot
removers, paint thinners, solvents, gasoline, or
similar fluids. These cleaners may damage the
rubber seals. The improper care or cleaning
methods may cause the convertible top and its
seams to leak. <
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

MOBILITYReplacing components
166
2.Press together the lo cking spring, arrows1,
and fold out the wiper blade, arrow 2.
3. Pull the wiper blade forward and out of the
catch mechanism.
4. Press the new wiper blade into the fixture
until it engages audibly.
To avoid damage, make sure that the
wiper arms are against the windshield
before you open the hood. <
MINI Convertible: wiper blade
replacement
1.Fold out the wiper arm and hold it.
2. Press locking spring together, arrows1.
3. Hold locking spring pressed together and
pull wiper blade from wiper arm, arrow 2.
4. Slide the new wiper blade onto the wind-
shield wiper arm until it audibly engages.
5. Fold down the wiper arm.
To avoid damage, make sure that the
wiper arms are against the windshield
before you open the hood. <
Lamps and bulbs
Lamps and bulbs make an essential contribution
to vehicle safety. They should, therefore, be
handled carefully. The manufacturer of your
MINI recommends having your MINI dealer per-
form any work that you do not feel competent to
perform yourself or that is not described here.
Never touch the glass of new bulbs with
your bare fingers, as even minute amounts of contaminatio
n will burn into the
bulb's surface and reduce its service life. Use a
clean tissue, cloth or some thing similar, or hold
the bulb by its base. <
You can obtain a selectio n of replacement bulbs
at your MINI dealer.
Only replace bulbs after they have cooled
down; otherwise, you may burn your
fingers. <
When working on electrical systems,
always begin by switching off the
consumer in question; ot herwise, short circuits
could result. To avoid possible injury or equip-
ment damage when replacing bulbs, observe
any instructions provided by the bulb manu-
facturer. <
Caring for headlamp s, refer to page162.
For any bulb replacement not described
below, contact a MINI dealer or a work-
shop that has specia lly trained personnel
working in accordance wi th the specifications
of the MINI manufacturer. <
For checking and adjusting headlamp aim,
please contact your MINI dealer. <
Light-emitting diodes LEDs
Light-emitting diodes installed behind translu-
cent lenses serve as the light sources for many of
the controls and displays in your vehicle. These
light-emitting diodes are related to conven-
tional laser diodes, and legislation defines them
as Class 1 light-emitting diodes.
Do not remove the covers or expose the
eyes directly to the unfiltered light source
for several hours; otherw ise, this could cause
irritation of the retina. <
Headlamp glass lens
In cool or humid weather, condensation may
occur on the interiors of the headlamps. The
condensation disappears a short time after the
light is switched on. The headlamps do not need
to be changed.
Do not remove the condensation from head-
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

Replacing componentsMOBILITY
167
lamps, despite driving with lights on, and if
condensation increases, e.g., because of water
droplets, have this checked by your MINI dealer.
Xenon lamps
The service life of these bulbs is very long and
the probability of failure very low, provided that
they are not switched on and off an excessive
number of times. If a xenon lamp fails neverthe-
less, switch on the fog lamps and continue the
journey with great care, provided that local
legislation does not prohibit this.
Work on the xenon lighting system,
including lamp replacem ent, is only to be
carried out only by your MINI dealer. Due to high
voltage, there is a risk of fatal injury if work on
the xenon lamps is carried out improperly. <
Halogen low beams and high beams
H13 bulb, 60/55 watts
The H13 bulb is pressurized. Therefore,
wear safety glasses an d protective gloves.
Otherwise, there is a risk of injury if the bulb is
damaged. <
Be careful when inst alling the cover;
otherwise, leaks co uld occur and cause
damage to the headlamp system. <
Accessing the lamp from the engine
compartment
The low-beam/high-beam bulb can be changed
from the engine compartment. Removing the cover:
1.
Press the tab.
2. Flip open the cover and take it out of the
holder.
Follow the same steps in reverse order to
reattach the cover. Be careful when inst alling the cover;
otherwise, leaks could occur and cause
damage to the headlamp system. <
Replacing the bulb
1.Turn the lamp counterclockwise, arrow 1,
and remove it, arrow 2.
2. Push on the catch, arrow 1, and disconnect
the connector, arrow 2.
3. To insert the new bulb and replace the
cover, proceed in reverse order.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

Replacing componentsMOBILITY
175
The jack base must be perpendicular to the
surface beneath the jacking point.
2. During jacking up, insert the jack head in the
square recess of the jacking point.
3. Jack the vehicle up until the wheel you are
changing is raised off the ground.
Mounting the space-saver spare tire
1.Unscrew the lug bolts and remove the
wheel.
2. Remove accumulations of mud or dirt from
the mounting surfaces of the wheel and
hub. Clean the lug bolts.
3. Lift the new wheel into place.
4. Screw at least two lug bolts finger-tight into
opposite bolt holes.
5. Screw in the remaining bolts.
6. Tighten all the lug bolts firmly in a diagonal
pattern.
7. Lower the vehicle.
8. Remove the jack.
Tightening the lug bolts
Tighten the lug bolts in a diagonal pattern.
Immediately have the wheels checked
with a calibrated torque wrench to ensure
that the lug bolts are firmly seated. Otherwise,
incorrectly tightened lug bolts can present a
safety hazard. <
Tightening torque: 103.3 lb ft or 140 Nm.
Replace the defective tire as soon as possible
and have the new wheel/tire assembly
balanced.
Vehicle battery
Maintenance
The battery is maintenance-free; that is, the
electrolyte will last for the life of the battery
when the vehicle is operated in a temperate
climate.
Battery replacement
Only use vehicle batteries that have been
approved for your vehicle by the manu-
facturer; otherwise, the vehicle could be
damaged and systems or functions may not
be fully available. <
After a battery replacement, have the battery
registered on the vehicle by your MINI dealer to
ensure that all convenie nce functions are fully
available and, if nece ssary, the corresponding
Check Control messages are no longer dis-
played.
Charging the battery
Note
Do not connect battery chargers to the
sockets installed in the vehicle at the
factory; otherwise you may cause damage to
the battery. <
Only charge the battery in the vehicle when
the engine is off. Connections, refer to Jump-
starting on page 177.
General information
To guarantee the full service life of the battery,
ensure that the battery is always properly
charged.
It may be necessary to charge the battery in the
following situations:
>If frequent short trips are taken.
> If the vehicle is frequently parked for more
than a month.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

MOBILITYIndicator and warning lamps
184
Fuel cap missing or looseMake sure that the fuel cap is correctly
positioned and close it until it audibly
clicks. Do not jam the strap between
the fuel cap and the vehicle.
Window washer fluid level too low Add washer fluid as soon as possible,
page 62.
Lights up in red:
Service due Arrange a service appointment.
Check service requirements,
page 159.
Lights up in yellow:
The next time that the Start/Stop
button is pressed, the engine starts,
possibly even without a foot on the
brakes or without depressing the
clutch
Remote control malfunctioning or, in
cars with Comfort Access, not
detected The engine cannot be started. Have
the remote control checked, if
necessary.
Remote control battery is discharged Use the remote control for a longer journey or, in cars with Comfort
Access, replace the battery.
Belt tensioners and/ or airbag system
failed Have the system checked immedi-
ately. Fasten the safety belts anyway.
Power steering failed You can continue your journey, but
moderate your speed and exercise
due caution. Steering response will be
markedly different. Have the system
checked without delay.
12Cause What to do
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

MOBILITYIndicator and warning lamps
192
Selector lever position P not engaged.
Ignition cannot be switched offEngage selector lever position P when
you wish to switch off the ignition,
page
55.
Cruise control system fail edHave the system checked.
Park Distance Control fail edHave the system checked.
Bulb of exterior lighting system failed Have the exterior lighting checked as
soon as possible.
Low-beam headlamp or fog lamp
failed Have the lamps checked as soon as
possible.
High-beam headlamp failed Have the high-beam headlamps
checked.
Rear fog lamp failed Have the rear fog lamp checked.
Headlamp beam throw adjustment
system failed Have the headlamp beam throw
adjustment system checked.
Coolant level too low Add coolant immediately, page158.
Engine oil pressure too low Stop immediately and switch off the
engine. You cannot continue your
journey. Contact your MINI dealer.
Lights up in red:
Service appointment overdue Arrange a service appointment.
Check service requirements, page 71.
Lights up in yellow:
Service due Arrange a service appointment.
Check service requirements, page 71.
12Cause What to do
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

Indicator and warning lampsMOBILITY
193
No service due
Set speed limit exceeded
Time and date no longer correct Set the time and date, page73.
12Cause What to do
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

Everything from A to ZREFERENCE
207
Bar, refer to Tow-starting, towing away 179
Base plate for telephone or mobile phone
– refer to Snap-in adapter 136
Battery 175
– disposal 33,176
– jump-starting 177
– temporary power failure 176
Battery renewal
– remote control 33
Being towed 179
Belts, refer to Safety belts 48
Belt tensioner, refer to Safety belts 48
Beverage holders, refer to
Cupholders 101
Black ice, refer to External temperature warning 66
Blower, refer to Air flow rate 95,97
Bluetooth, activating/
deactivating 130
Bottle holders, refer to Cupholders 101
Brake Assist 76
Brake fluid, refer to Service requirements 71
Brake lamps
– replacing bulbs 169
Brake pads, breaking in 106
Brake rotors 108
– brakes 106
– breaking in 106
Brakes
– ABS 76
– breaking in 106
– MINI Maintenance System 159
– parking brake 57
– refer to Braking safely 107
– service requirements 71
Brake system 106
– breaking in 106
– disc brakes 108
– MINI Maintenance System 159 Breakdown service, refer to
Roadside Assistance 177
Breaking in the clutch 106
Break-in period 106
Bulb changing, refer to Lamps and bulbs 166
Button for starting the
engine 55
Buttons on the steering wheel 11
C
California Proposition 65
warning 5
Call ending 134
Calling, refer to Phone numbers, dialing 134
Calling, refer to Telephone 100
Can holders, refer to Cupholders 101
Capacities 205
Car battery, refer to Vehicle battery 175
Car care 161
Care 161
– car-care products 161
– car washes 161
– CD/DVD drives 164
– high-pressure washers 162
– leather 164
– manual washing 162
– upholstery and fabrics 163
– windows 162
– wiper blades 162
Cargo, securing 111
Cargo area 108
– capacity 203
– Comfort Access 32
– emergency operation, see manual unlocking 28
– lamp 92
– opening from outside 28
Cargo area lid, refer to Tailgate 28 Cargo loading
110
– securing cargo 111
– stowing cargo 111
– vehicle 108
Car key, refer to Keys/remote controls 22
Carpets, care 164
Car phone
– installation location, refer to Center armrest 100
– refer to Telephone 100,128
Car radio, refer to Radio 16
Car wash, care 161
Car washes 161
Catalytic converter, refer to Hot exhaust system 107
CD player 121
– changing the track 121
– fast forward/reverse 121
– playing a track 122
– random order 121
– volume 116
Center armrest 100
Ce

nter brake lamp 170
Center console, refer to
Around the center
console 14
Central locking system 23
– Comfort Access 31
– from inside 27
– from outside 23
Changing bulbs 166
Changing wheels 173
Charging the battery 175
Chassis number, refer to Engine compartment 155
Check Control 73
Child restraint fixing system LATCH 52
Child restraint systems 51
Child seats 51
Chrome parts, care 163
Chrome parts, refer to Care 161
Cigarette lighter 101
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG

REFERENCEEverything from A to Z
208
Cleaning headlamps62
– washer fluid 62
Clock
– setting time 73
– 12 h/24 h mode 70
Closing
– from inside 27
– from outside 23
Clothes hooks 100
Cockpit 10
Cold start, refer to Starting the engine 56
Comfort Access 31
– replacing the battery 33
– what to observe before entering a car wash 32
Comfort area, refer to Around the center console 14
Compartment for remote
control, refer to Ignition
lock 55
Compressed audio files 121
Computer 66
Condensation, refer to When the vehicle is parked 108
Condition Based Service CBS 159
Configuring settings, refer to
Personal Profile 22
Connecting vacuum cleaner,
refer to Connecting electrical
appliances 101,102
Consumption, refer to Average
fuel consumption 66
Control Display
– settings 68
Controls and displays 10
Convenience operation
– windows 24
Convenient access, refer to Comfort Access 31
Convenient start, refer to
Starting the engine 56
Convertible top 34
– manual 39
– mechanical 39 Coolant
158
– checking level 158
– filling 158
– temperature 158
Cooling, maximum 97
Cooling fluid, refer to Coolant 158
Copyright 2
Cornering light, refer to Adaptive Light Control 90
Cruising range 66,67
Cupholders 101
Curb weight, refer to
Weights 203
Current fuel consumption 67
D
Dashboard, refer to Cockpit
10
Dashboard instruments, refer to Displays 12
Dashboard lighting, refer to
Instrument lighting 92
Data 196
– capacities 205
– dimensions 197
– engine 196
– weights 203
Data memory 160
Date
– setting 73
Daytime running lights 89
DBC Dynamic Brake Control,
refer to Brake Assist 76
Deactivating front passenger airbags 85
Deadlocking, refer to Locking 25
Defect
– door lock 27
– fuel filler flap 140
Defogging windows 96,98
Defrosting windows 96,98
Defrosting windows and removing condensation
– air conditioner 96
– automatic climate control 98Defrosting windshield, refer to
Defrosting windows 96,98
Defrost positi on, refer to
Defrosting windows 96,98
Differential, breaking in 106
Digital radio, refer to HD Radio 119
Dimensions 197
Dipstick, engine oil 156
Directional indicators, refer to
Turn signals 60
Displacement, refer to Engine data 196
Display lighting, refer to Instrument lighting 92
Displays 12
– care 164
– instrument panel 12
Displays and controls 10
Disposal
– of coolant 158
– remote control battery 33
– vehicle battery 176
Distance remaining to service, refer to Service
requirements 71
Distance warning, refer
to Park
Distance Control PDC 75
Door key, refer to Integrated key/remote control 22
Door lock 26
Door lock, confirmation signals 25
Doors, manual operation 27
DOT Quality Grades 151
Drinks holders, refer to
Cupholders 101
Drive-off assistant, refer to Hill Assist 78
Driving dynamics control, refer to Sport button 78
Driving lamps, refer to Parking
lamps/low beams 88
Driving notes 106
Driving off on inclines, refer to
Hill Assist 78
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG