fuel filter MITSUBISHI 3000GT 1991 Service Manual

,
b
00-I
GENERALCONTENTS
MOOOA- .
GENERAL DATA AND SPECIFICATIONS . . . . . .21
HOW TO USE THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . .3Definition of Terms
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Explanation of Circuit Diagrams
. . . . . .._...........7Explanation of Manual Contents
. . . . . . . . . . . . . . . . . . . .4
Explanation of the Troubleshooting Guide . .
6ModelIndications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Scope of Maintenance, Repair and
ServicingExplanations
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Troubleshooting
. . . . . . .._.......................................3
LUBRICATION AND MAINTENANCE. . . . . .._....31SCHEDULED MAINTENANCE TABLE. . . . . . .._.
MAIN SEALANT AND ADHESIVE TABLE. . .44
MAINTENANCE SERVICE
. . . . . . . . . . . . . . . .._......_.....__Air Cleaner Element
. . . . . . .._......._......_................Automatic Transaxle
. . . . . . . . . . . . . . . . . . . . . . . . .._......._.....Ball Joint and Steering Linkage Seals
. . . . . . . . . . . .
BrakeHoses. . . . . . . . . . . . . . . . . . . . . . . . . . . .._......._.._...._......._..
Disc Brake Pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Drive Belt (For Alternator)
. . . . . . . . .._.........._..........Drive Shaft Boots
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine Coolant
. . . . . . . . . . . . ..__.._.............................Engine Oil
.._....__._.................................................Engine Oil Filter
. . . . .._._.......__.................. . . . . . . . . . . .Exhaust System
_....._......._.....__._............,...........Fuel Hoses
..__......__............................................36
3740
42
42
42
38
43
41
38
39
43
36
FuelSystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Manual Transaxle
. . . . . . . . . .._........................_.......Rear Axle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._..._.._..____.._.......
SparkPlugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._...............TimingBelt
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MASTER TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS BEFORE SERVICE. . . . . . . . . . . . . . . .
RECOMMENDED LUBRICANTS AND
LUBRICANT CAPACITIES TABLE. . . . . . .._........
SPECIAL HANDLING INSTRUCTIONS
FOR AWD MODELS. . . . . . . . . . . . .._...._........................
TIGHTENING TORQUE. . . . . . . . . . . . . . . ..__.....................
TOWING AND HOISTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . .._.....Chassis Number .
.._............................................Engine Model Stamping
.._..........................._...._Theft Protection
. . . . .._.........................................Vehicle Identification Code Chart Plate
.._.....Vehicle Identification Number List
.._._....._..._.Vehicle Identification Number Location
. . . .._
Vehicle Information Code Plate . . . . .._._......_.......Vehicle Safety Certification Label
. . . ..I . . . . .._..._...
36
3943
37
3724
1532
35
20
23
16
8
10
11
11
8
9
8
10
10

00-32 GENERAL - Recommended Lubricants and Lubricant Capacities Table
RECOMMENDED LUBRICANTS AND LUBRICANT CAPACITIES TABLE
MOORA- -RECOMMENDED LUBRICANTS
\L/
DIA-QUEEN LONG-LIFE COOLANT (Part No. 0103044) orLUBRICANT CAPACITIES TABLE
Description
Engine oil
Crankcase
(excluding oil filter and oil cooler)
Oil filter
Oil cooler (Turbo)
Cooling system (including heater and coolant
reserve system)
Manual transaxle


Transfer
Automatic transaxle
Rear axle
Power steering
<2ws>
<4ws>
Fuel tank
Metric measureU.S. measure
4.0 liters4.2 qts.
0.3 liter1/2qt. s
0.21 liter112 qt.
8.0 liters8.5 qts.
2.3 liters2.4 qts.
2.4 liters
2.5 qts.
0.27 liter.29 qt.
7.5 liters
7.9 qts.
1
.I liters1.16qts.
0.9 liter
.95 qt.
1.5 liters1.59 qts.
75 liters
19.8 gals.
TSB Revision1
d

00-36GENERAL - Scheduled Maintenance Table / Maintenance Service
SCHEDULED MAINTENANCE UNDER SEVERE USAGE CONDITIONS
The maintenance items should be performed according to the following table:
Mileage Intervals Kilometers in ThousandsSevere Usage
MaintenanceService to be(Miles in Thousands)Conditions
itemPerformed
(6 (15) (22.5) (30) (37.5) (45) (50) (52.5) (60)24 36 48 60 72 80 84 96 A B C D E F G
Air Cleaner ElementReplaceMore FrequentlyXX
Spark PlugsReplaceXXXXXX
Engine OilChange Every Or3 MonthsEvery 4,800 Km (3,000 Miles)x x x xX
Engine Oil FilterReplace Every or6 MonthsEvery 9,600 Km (6.000 Miles)x x x xX
Disc Brake PadsInspect for WearMore FrequentlyXX
Severe usage conditions
A-Driving in dusty conditionsE -B -Police, taxi, or commercial type operationF -Driving in sandy areas
C -Extensive idlingG -Driving in salty areas
D -Short trip operation at freezing temperaturesMore than 50% operation in heavy city traffic during
(engine not thoroughly warmed up)hot weather above 32°C (90°F)MAINTENANCE SERVICE
1. FUEL SYSTEM (TANK, LINES, CONNECTIONS
AND FUEL FILLER CAP) (Check for leaks)
/ 2.
FUEL HOSES (Check for leaks or damage)MWShGC
1. Check for damage or leakage in the fuel lines and
connections and looseness of the fuel filler cap.
2.Inspect the surface of fuel hoses for heat and mechanical
damage. Hard and brittle rubber, cracking, checking, tears,
cuts, abrasions and excessive swelling indicate deteriora-
tion of the rubber.
3.If the fabric casing of the rubber hose is exposed by cracks
and abrasions in the fuel system, the hoses should be
changed.
TSB Revision

FUEL
SYSTEM
CONTENTSM13AA- _
CRUISE CONTROL SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . .158SPECIFICATIONS. . . . . . . .._._....................................................155
CRUISE CONTROL SYSTEM*................................................185
SERVICE ADJUSTMENT PROCEDURES............................178
Cruise Control Cables Inspection and Adjustment........178Cruise Control SystemInspection....................................179individual Parts Inspection....................................................181
SPECIAL TOOLS........................................................................159
SPECIFICATIONS....................................................................158
General Specifications........................................................158Service Specifications........................................................158
TROUBLESHOOTING............................................................159
Check Chart............................................................................163Harness and Components Layout....................................176Preliminary Inspection........................................................159Self-diagnosis Checking........................................................172Troubleshooting Quick Reference Chart............................159
ENGINE CONTROL............................................155
ENGINE CONTROL................................................................157
SERVICE ADJUSTMENT PROCEDURES............................156
Accelerator Cable Inspection and Adjustment................156Accelerator Switch Inspection and Adjustment................156
Service Specifications........................................................
155
TROUBLESHOOTING............................................................
155
Accelerator Cable and Accelerator Pedal........................155
FUEL SYSTEM....................................................3
DETONATION SENSOR........................................................154
FUEL FILTER............................................................................
153
FUEL LINE AND VAPOR LINE................................................151
FUEL PUMP AND FUEL GAUGE UNIT ASSEMBLYAND OVERFILL LIMITER (TWO-WAY VALVE)................149
FUEL TANK.................................................................................146
GENERAL INFORMATION
....................................................
3
MPI System Diagram............................................................3
INJECTOR................................................................................141
ON-VEHICLE INSPECTION OF MPI COMPONENTS........36
Active Exhaust Control Unit ............................130Air Conditioner Switch and Power Relay............................82Air Flow Sensor....................................................................54Anti-lock Brake Signal ........................................133Barometric Pressure Sensor................................................60CONTINUED ON NEXT PAGE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP
528 -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

Tank capacityliter (gal.)
Return system
Filter
High pressure type
Electrical, in-tank type
Driven by
Throttle position sensor
idle speed control servoVariable resistor type
Stepper motor typeThe stepper motor type by-pass air controlsystem with the first idle air valve
Engine control unit
Identification model No.
Federal

California
Karman vortex type
Barometric pressure
sensorSemiconductor diffusion type
Engine coolant temperature sensor
Oxygen sensor
Vehicle speed sensor
Detonation sensor
Top dead center sensor
Crank angle sensor
Induction control valve position sensor
EGRtemperature sensor Reed switch type
Piezoelectric device type
Photo interrupter type
Photo interrupter type
Variable’resistor type
13-6FUEL SYSTEM - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-101INJECTORS
M13YTAC2
IInjectorII\- 7FUO803
7FI
FuelFilter
@Injection
7FUO83:2Connector for
rear bank
Engine control unit7FUO833
Engine control unit connector
7FUO653
OPERATIONlThe injector is an injection nozzle with a solenoid valve which injects fuel according to the injection signal
coming from the engine control unit.
lThe injector has a fixed nozzle opening area and the fuel pressure against manifold inside pressure is
regulated to a fixed level. Therefore, the volume of fuel injected by the injector is determined by the time
during which the needle valve is open, namely, by the time during which the solenoid coil is energized.
lThe battery voltage is applied through the control relay to this injector. When the engine control unit turns
on the power transistor in the unit, the solenoid coil is energized to open the injector valve, which then
injects fuel.
TSB Revision

/
L
LFUEL SYSTEM
- On-vehicle Inspection of MPI Components13405INJECTORS
(Front bank connector)
\/-I- 7FUO80:
3Engine control unit connector
FuelFilter
@Injection
7FUO832Injector
No. 1
coscliio-:Engine
control
unitControl relay@ Equipment side
connector
8
Injector(OscliioJ1Injector
No.5
1
(osclllo)d2
4-(’I
:1
-1
74
----
;3A14
Bris+
5
5----_Injector
-----
2Ioscillo)<
15--60
Rear bank
connector
7FUO973
7FUO653
OPERATION
TROUBLESHOOTING HINTSRefer to “INJECTOR”
(P.13-101).
TSB Revision

FUEL SYSTEM - Orwehicle lnwection of MPI Components.13-137Fuel gauge cover
03FOOO4
j check terminal ----T( 04~oo1,/RELEASE OF RESIDUAL PRESSURE FROM HIGH
PRESSURE FUEL HOSEM13FGAIMake the following operations to release the pressure remain-
ing in fuel pipe line so that fuel will not flow out.
(I) Remove the fuel gauge cover in the luggage compartment.
(2) Disconnect the fuel pump harness connector.
(3) Start the engine and after it stops by itself, turn the ignition
switch to OFF.
(4) Connect the fuel pump harness connector.
(5) Apply the specified sealant to the rear floor pan.
Specified sealant: 3M ATD Part No. 8509 or equivalent
(6) Install the fuel gauge cover.
FUEL PUMP OPERATION CHECK
M13FDAI
(1) Set the ignition switch at OFF.
(2) Check that when the battery voltage is directly applied to
the fuel pump check terminal (black), the operating sound
of the pump can be heard.
NOTESince the fuel pump is installed in the fuel
.tank, its
operating sound cannot be readily heard. Remove the fuel
tank cap and listen to the operating sound through the filter
port.
(3) Hold the high pressure fuel hose between your fingers and
check that the fuel pressure can be felt.
TSB Revision

FUEL SYSTEM - On-vehicle Inspection of Mql Components13439(10)Disconnect the vacuum hose from the fuel pressure
regulator, and then measure the fuel pressure while using a
finger to plug the end of the hose.
Standard value:
330
- 350 kPa (47 - 50 psi) at curb idle
295 - 315 kPa (43 - 45 psi) at curb idle(11
)Check to be sure that the fuel pressure during idling does
not decrease even after the engine is raced a few times.
(12)Use a finger to gently press the fuel return hose while
repeatedly racing the engine, and check to be sure that
there is fuel pressure in the return hose also.
NOTEThere will be no fuel pressure in the return hose if there is
insufficient fuel flow.
(13)lf the fuel pressure measured in steps (9) to (12) deviates
from the standard value range, check for the probable
cause by referring to the table below, and. then make the
appropriate repair.
IConditionProbable cause1 RemedyI
l Fuel pressure is too low.l Fuel pressure drops duringracing.l No fuel pressure in fuel returnhose.
Malfunction of the valve seat withinthe fuel pressure regulator, or fuel
leakage to return, side caused byReplace the fuel filter.
Replace the fuel pressure regulator.
Fuel pump low discharge pressure.Replace the fuel pump.
Fuel pressure is too high.
The valve within the fuel pressureregulator is sticking.Replace the fuel pressure regulator.
Clogging of the fuel return hose and/Clean or replace the hose
and/oror the pipe.pipe.
No change of the fuel pressureDamaged vacuum hose or nippleReplace the vacuum hose, or clean
when the vacuum hose is connected clogging.the nipple.
and when not connected.
Malfunction of the fuel pressure controlChecking the fuel pressure controlsystem system
1 TSB Revision

13-144FUEL SYSTEM - Throttle- Body
DISASSEMBLY AND REASSEMBLY
2.0
Nni1.4ft.lbs.
/
Disassembly steps
1. Dash pot2. Hose
3. Vacuum valve
>

l *4. Throttle position sensor
(within idle position switch)
5.
Idle speed control servo
assembly
6. Throttle body
7FU1023
\7FU1057 1SERVICE POINT OF DISASSEMBLY
MlBSFAN
Caution
1.When loosening a Phillips screw which has been firmly
tightened, use a Phillips screwdriver that is an exact fitfor the screw.
2. Do not remove the throttle valve.
3.Be careful when removing the throttle position sensorand idle speed control servo mounting screws, as
adhesive has been applied these screws.
INSPECTION
Ml3SHAt.lDASH POT INSPECTION
(1) Check the dash pot diaphragm for damage. First, push up
the rod fully and closing tightly the nipple with a finger,
release the rod. The diaphragm is intact if the rod does not
return to the initial position while the nipple is held closed
with a finger. If the rod returns, the diaphragm is broken.
Replace the dash pot.
VACUUM VALVE INSPECTION
(1) Remove the filter from the vacuum valve.
(2) Connect a hand vacuum pump to the black nipple of the
vacuum valve.
(3) With the other nipple closed by the finger, apply a negative
pressure of 500 mmHg (19.7 in.Hg.) to make sure that the
negative pressure is maintained.
(4)Let go your finger and make sure that the negative pressure
leaks out gradually.
hSB Revision1