set clock MITSUBISHI 3000GT 1991 Service Manual

ENGINE - Service Adiustment ProceduresII-13
I_ ianltion tlminaI!H Connector for Igdpstment 6rown)
4tll II -7FUO9371IGNITION TIMING ADJUSTMENTMllFLAF
(1) The vehicle should be prepared as follows before the
inspection and adjustment.
lEngine coolant temperature: 80 - 95°C (176 - 205°F)
l Lights, electric cooling fan and accessories: OFF
l Transaxle: neutral
(P for A/T)l Steering wheel: neutral position
(2) Insert a paper clip to the connector, and connect a
tachometer to the paper clip.
NOTEDo not use the Multi-use tester.
If tested with the Multi-use tester connected to the
diagnosis connector, the ignition timing will not be the basic
timing but be ordinary timing.
(3) Set the timing light.
(4) Start the engine and run at idle.
(5) Check curb idle speed.
Curb idle speed: 700
f 100 rpm
NOTEThe engine speed indicated is a third of actual speed. In
other words, the reading of the tachometer times 3 is actual
speed.
(6) Turn OFF the ignition switch.
(7) Using a jumper wire, ground the ignition timing adjusting
terminal.
NOTEGrounding this terminal sets the engine to the basic ignition
timing.
\(8) Start the engine and run at idle.
(9) Check basic ignition timing.
Basic ignition timing: 5” BTDC
k 2”
(10)lf not within the standard value range, loosen the crank
angle sensor mounting nut and adjust by turning the crank
angle sensor. Turning it to the counterclockwise retards
timing, and to the clockwise advances it.
(1 l)After adjustment, tighten mounting nut taking care not to
move the crank angle sensor.
(12)Turn OFF the ignition switch.
(13)Disconnect the jumper wire connected at step (7).
(14)Start and run the engine at curb idle speed.
1 TSB Revision

ENGINE - Timing Belt11-29
OlN004t
& Pin hole
nilnq
8(2) Using paper clips, install the timing belt in the following
order with care not to allow the belt to slack.@ Exhaust camshaft sprocket (front bank side)
+ @
Intake camshaft sprocket (front bank side)
-+ @Waterpump pulley
+ @ Intake camshaft sprocket (rear bank
side)
+ @ Exhaust camshaft sprocket + @ Idler pulley
-+ @ Crankshaft sprocket + @ Tensioner pulley
NOTESince the camshaft sprockets turn easily, secure them
with box wrenches to install the timing belt.
Caution1. Be careful, the camshaft is turned by the reac-
tion of valve spring.
2.If the timing belt is reused, install it so that thearrow marks made at removal are in the direc-
tion of rotation.
(3) Turn the tensioner pulley so that its pin holes are
located above the center bolt. Then, press the tensioner
pulley against the timing belt and, at the same time,
temporarily tighten the center bolt.
(4) Check that the timing marks on all sprockets are aligned
properly.
(5) Remove the four clips.
. ADJUSTMENT OF TIMING BELT TENSION
(1) Rotate the crankshaft
114 turn counterclockwise, then
rotate it clockwise until the timing marks are aligned.
(2) Loosen the center bolt on the tensioner pulley. Using
the special tool and torque wrench, apply tensioning
torque to the timing belt and, at the same time, tighten
the center bolt to specification.
Specified torque:
10 Nm (7 ftlbs.)
[Timing belt tensioning torque]
Caution
When tightening the center bolt, make sure that thetensioner pulley is not rotated together.
(3) Remove the set pin from the auto tensioner. At this
time, make sure that the set pin can be easily removed.
(4) Rotate the crankshaft two turns clockwise and leave it
as is for five minutes or more. Then, check again that
the set pin can be easily removed from, and installed to,
the auto tensioner.
NOTEEven if the set pin cannot be easily inserted, the auto
tensioner is normal if its rod protrusion is within
specification.
Standard value (A): 3.8
- 4.5 mm (.I49 - .I77 in.)
If the protrusion is out of specification, repeat steps (1)
to (4).
(5) Check again that timing marks on all sprockets are
aligned properly.
TSB Revision

FUEL SYSTEM - Service Adjustment Procedures
(3) Insert a 0.65-mm-thick feeler gauge between the fixed SASand throttle lever.
Terminal @
(sensor output)zensor g&nd)MB991348
1
(4) Loosen the throttle position sensor mounting bolts and turnthe TPS body fully counterclockwise.
(5) In this condition, check that there is continuity across
terminals
@ and @.
(6) Slowly turn the throttle position sensor clockwise until you
find a point at which there is no continuity across terminals
@ and 0. Then, tighten the throttle position sensor
mounting bolt securely.(7) Connect the throttle position sensor connector.
(8) When using the multi-use tester, connect it to the diagnosis
connector.
(9) When not using the multi-use tester, proceed as follows:
@ Disconnect the throttle position sensor connectors andconnect the special tool, Test Harness Set, between
the disconnected connectors.
@ Connect a digital voltmeter between the throttle posi-
tion sensor terminal @ (sensor output) and teminal @
(sensor ground).
(lO)Turn the ignition switch ON (but do not start the engine).
(IlKheck the throttle position sensor output voltage.
When using the multi-use tester, select item No. 14 and
read the throttle position sensor output voltage.
Standard value: 400 - 1,000 mV
(12)lf the voltage is out of specification, check the throttle
position sensor and associated harnesses.
(13)Remove the feeler gauge.
(14)Turn the ignition switch OFF.
TSB Revision
1

FUEL SYSTEM - Throttle Body13-145Orifice
Nipple (green)3EM05iGroundThrottle
positlonsensor output
Idle-position
switchTh>ottle position
sensor power7FUO535(5) Disconnect the hand vacuum pump and connect it to the
other nipple.
(6)Make sure that the negative pressure leaks out as soon as it
is applied.
CLEANING THROTTLE BODY PARTS
(1) Clean all throttle body parts.
Do not use solvent to clean the following parts:
l Throttle position sensor (Idle position switch)
l Idle speed control servo
If these parts are immersed in solvent, their insulation will
deteriorate.
Wipe them with cloth only.
(2) Check if the vacuum
pot-t or passage is clogged. usecompressed air to clean the vacuum passage.
SERVICE POINT OF REASSEMBLY
M13SGAN4. INSTALLATION OF THROTTLE POSITION SENSOR
(1) Set the throttle position sensor to the throttle body as
shown in the diagram.
(2) After turning the throttle position sensor 90” in the
clockwise direction to set it, tighten by turning the
screw.
(3) Connect the circuit tester between 1 (ground) and 3
(output), or between 3 (output) and 4 (power). Then,
make sure that the resistance changes smoothly when
the throttle valve is slowly moved to the fully open
position.
(4) Check for continuity across terminals 2 (Idle position
switch) and 1 (ground) with the throttle valve both fully
closed and fully open.
IThrottle valve positionIContinuityI
Fully closedConductive
Fully openINon-conductiveIIf there is not continuity with the throttle valve fully
closed, turn the counterclockwise direction, and then
check again.
(5) If the above specifications are not met, replace the idle
position switch.
1 TSB RevisionI

13-182CRUISE CONTROL SYSTEM - Service Adjustment ProceduresI
CRUISE CONTROL SWITCH INSPECTION(1) Remove the air bag module using the following procedure.I07FOO12
07NOOl@ Remove the negative terminal of the battery and wait
for more than 30 seconds.
d
CautionThe capacitor in the SRS diagnosis unit retains
enough voltage to deploy the air bag for a given
period even after disconnection of the battery. If anoperation is performed during that given period,
unintended deployment of the air bag could result
and cause serious injury.@Remove the air bag module. To remove the clock spring
connector
(squib connector) from the air bag module,
force the lock outward and pry it with a plain screwdriv-
er as shown at left so that no undue force will be
exerted on the connector when it is removed.@ The removed air bag module should be stored in a
clean, dry, flat place with the pad side up.
(2) Disconnect the connector of the control switch and operate
the control switch to measure the resistance between the
individual terminals.
If the readings are as shown below, the control switch may
be considered good.
Switch operationResistance between-iJ
terminals
When switch is not operated
When switch is operated toward you
(CANCEL switch: ON)
When switch is operated upward
(RESUME switch: ON)
When switch is operated downward
(SET switch: ON)No continuity
Approx. 0
1RApprox. 820
1RApprox. 2,700
fi
TSB Revision

23-1
AUTOMATIC
TRANSAXLE
CONTENTSMZJAA- _
ANNULUS GEAR AND TRANSFER DRIVE GEARTransmission Fluid Level Inspection................................46SET................................................................................................
102Transmission Fluid Replacement........................................
46
DIFFERENTIAL........................................................................104SPECIAL TOOLS........................................................................
16
:......................................... 12IEND CLUTCH ASSEMBLY....................................................99SPECIFICATIONS..........................
FRONT CLUTCH ASSEMBLY................................................95
GENERAL INFORMATlON....................................................2
KICKDOWN SERVO................................................................
107
LOW-REVERSE BRAKE............................................................
107
OIL PUMP....................................................................................93
PLANETARY GEAR................................................................
100
REAR CLUTCH ASSEMBLY....................................................97
SELECTOR LEVER ASSEMBLY............................................58
SERVICE ADJUSTMENT PROCEDURES............................46
Accelerator Switch
Inspection and Adjustment................
50Drive Shaft Oil Seals Replacement....................................
52Inhibitor Switch and Control Cable Adjustment................
52Key Interlock Mechanism Check........................................50KickdownServo Adjustment................................................
47Line Pressure Adjustment....................................................
48Reducing Pressure Adjustment........................................
49Selector Lever Operation Check........................................
50Shift Lock Mechanism Check............................................51Speedometer Cable Replacement....................................53
General Specifications........................................................12Lubricants............................................................................15Service Specifications........................................................12Spacer and Snap Ring........................................................13Valve Body Spring Identification Chart............................13
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................106
TRANSAXLE ASSEMBLY........................................................62
TRANSAXLE CONTROL*........................................................54
TRANSAXLE OIL COOLER, HOSES, TUBES
....................66
TRANSFER SHAFT....................................................................92
TROUBLESHOOTING............................................................
19
A/T Safety-lock System Troubleshooting........................44Converter Stall Test............................................................
43
Diagnosis and Test
................................................................
22
Element in Use at Each Position of Selector Lever........31Inspection
of ControlSystem............................................
28Inspection of Electronic Control System Components....32Oil Pressure Tests................................................................
39ShiftPatterns....................................................................
31,42Troubleshooting Guide........................................................
20
VALVE BODY. . . .._._.................................................................... 108
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3668GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
(3) MlTSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
ISRS or any SRS-related component.

23-56AUTOMATIC TRANSAXLE - Transaxle ControlOQPOOQQ
09FOO5
INSPECTIONM231CAMl Check the control cable for function and for damage.
lCheck the outer cable (key interlock cable, shift lock cable)
’for damage and spring for breakage and tension.~J
lCheck the inner cable (key interlock cable, shift lock cable)
for extension.
REVERSE
(R) POSITION ALARM BUZZER
Check that the buzzer sounds when battery voltage is applied
across terminals.
SERVICE POINTS OF INSTALLATIONM231DAW
19. CONNECTION OF SHIFT LOCK CABLE (BRAKE PEDAL
SIDE)Connect the shift lock cable so that its threads measure
about 4 mm
(.16 in.).
CautionDo not change the routing of shift lock cable to the
selector lever assembly.
16. INSTALLATION OF SLIDE LEVER / 15. KEY INTERLOCK
CABLE (STEERING LOCK ASSEMBLY SIDE) / 14. CAM
LEVER(1) Place the ignition key at the “LOCK” position or keep it
removed.
(2) Install the slide lever, key interlock cable, and cam lever
to the steering lock assembly as shown.
Caution
Do not change the routing of key interlock cable tothe selector lever assembly.
5. CONNECTION OF TRANSAXLE CONTROL CABLE
(SELECTOR LEVER ASSEMBLY SIDE)Connect the transaxle control cable, then make the follow-
ing adjustment.
(1) Place the selector lever in “N” position.
(2) Loosen the nut and slightly pull the transaxle control
cable in the direction of the arrow; then, tighten the nut.
4.CONNECTION OF SHIFT LOCK CABLE (SELECTOR LEV-
ER ASSEMBLY SIDE)(1) Place the selector lever in “P” position.
(2) Disconnect the key interlock cable from the selector
lever assembly side.
(3) Turn the lock cam B counterclockwise (arrow
0) to
move the set lever upward (arrow
0)._.-(4) Frt the cutout in set lever to the jock pm ot lock cam B. u
TSB Revision

37A-26
STEERING - Power Steerina Gear Box
Apply grease
Approx. 1 mm
l-(Approx. .040 in.)
Tool
13POO76
End plug
Sealant
13K130
’ IEnd plug
r=13K132
MB991 006-01
(2) Apply multipurpose grease to pinion gear and housing
bearing.(3) Wrap vinyl tape around the serrated part so that the oil
seal won’t be damaged when the pinion and valve
assembly is installed to the valve housing.
(4) Mount the pinion and valve assembly to the valve
housing.
18. INSTALLATION OF OIL SEALUsing a tool, press the oil seal into the valve housing.
CautionIn order to eliminate a seal malfunction at the valve
housing alignment surface, the upper surface of the oil
seal should project outward approximately 1 mm
(.040in.) from the housing edge surface.
11. INSTALLATION OF END PLUG
(1) Apply the semi-drying sealant to the threaded part of
the end plug.
Specified sealant: 3M ART Part No. 8663 or equiva-
lent(2) Secure the threaded portion of the end plug at two
places by using a punch.
. ADJUSTMENT OF TOTAL PINION TORQUE
(1) Position rack at its center. With special tool, tighten rack
support cover to 15 Nm (11
ft.lbs.1.(2) In neutral position, rotate pinion shaft clockwise one
turn/4
- 6 seconds with special tool. Return rack
support cover 30”
- 60” and adjust torque to the
standard value.
Standard value: 0.6
- 1.3 Nm (5 - 11 in.lbs.)
Caution1. When adjusting, set the standard value at its
highest value.2. Assure no ratcheting or catching when operat-
ing rack towards the shaft direction.
NOTEWhen it cannot be adjusted within the specified return
angle, check rack support cover components or replace.
ii1
I1
I
I
I
I1
I
I
I
I
yl (
I
I1
I1
I
I1
I
I\(3) After adjusting, lock rack support cover with lock nut.
i/
TSB Revision

42-2BODY - SDecifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
M42CA. -
Items
Hood
Type
Specifications
Rear hinged, front
opening type (with gas damper)
Door
Construction
Regulator system
Locking system
Liftgate
Type
Front-hinged, sashless
Wire type
Pin-fork type
Inner-hinged, with gas damper
Glass installation method
Windshield glassAdhesive type
Quarter window glassAdhesive type
Liftgate window glassAdhesive type
Glass thicknessmm (in.)
Windshield glass5.3 (.21)
Liftgate window glass3.5 (.I41
Door glass5.0 f.20)
Quarter window glass3.5 (.14)
Power window motor
TypePermanent magnet type (Built-in circuit breaker)
Revolutions under no load
rpm75 or more
Revolutions under load
vm
At 1 Nm (.72 ft.lbs.145-75
At 2 Nm (1.45 ft.lbs.)50-80
Bound current A
34 or less
Direction of rotationClockwise and counter-clockwise
Power window main switch
TypeAutomatic reset type
Rated load currentA
Lock switch
10Power window switch
10
Power window sub switch
TypeAutomatic reset type
Rated load currentA10
Power window relay
Maximum contact current
A20
Rated coil current
AMax. 0.2
Voltage drop between terminals
V0.2 or less
(At 12 V and the rated load current)TSB Revision

52B-24 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - Troubleshooting
TEST 4NO COMMUNICATION BETWEEN MULTI-USE TESTER AND SDU
(SRS warning light does not illuminate)
IGNITION SWITCH(IG1)
J/.8(MULTI -PURPOSEFUSES)
SRS DIAGNOSIS UNIT
MULTI -3SETESTER1
KKRS-AX-RISE+R
View ASRS diagnbsis unit
To front impact sensor
(L.H.)
\To front impact sensor (R.H.)Toclock spring
I19FOllO
To body wiring harness (14-pin)
onnectornotch -UNLOCKED
;;bb;;,LOCKED zRok
(1) Turn the ignition key to the “LOCK” position, disconnect
the negative battery cable and tape the terminal.
Caution
Wait at least 30 seconds after disconnecting the battery
cable before doing any further work. The SRS system is
designed to retain enough voltage to deploy the air bagfor a short time even after the battery has been
disconnected, so serious injury may result from unin-
tended air bag deployment if work is done on the SRSsystem immediately after the battery cable is discon-
nected.(2) Remove the rear.console assembly. (Refer to GROUP 52A
- Floor Console.)
(3) Use a screwdriver to push in the lock spring of the lock
lever of the SRS diagnosis unit to unlock the lock lever.
Caution
A double-lock mechanism is employed for the connec-
tor of the SRS diagnosis unit, so care must be taken notto damage it by using excessive force or by not
disconnecting it correctly.
idi
I
I
I
I
I
I
I
L)I
I
I
I1
I
I~
i(4) Disconnect the red l4-pin connector from the SRS diagno- L/~
sis unit while pressing down the lock of the connector.
(Refer to
P.52B-9.)
\
TSB Revision