turn signal bulb MITSUBISHI 3000GT 1993 2.G Workshop Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1993, Model line: 3000GT, Model: MITSUBISHI 3000GT 1993 2.GPages: 738, PDF Size: 35.06 MB
Page 213 of 738
Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Buzzer Circuit211
OPERATION
L
lBattery positive voltage is continuously applied to the key-reminder switch.l
If the driver’s door is opened (door switch ON) with the key inserted in the ignition switch (key-reminderswitch ON), the buzzer sounds to warn that the key has been left in the switch.
&eat belt warning>
lWhen the ignition switch is turned on, the timer circuit and pulse circuit will flicker the seat belt warning
light for approx. 6 seconds with the buzzer intermittently sounding.
lIf the seat belt is fastened for the while, the seat belt switch will be turned off and the buzzer will
stop.
TROUBLESHOOTING HINTS
/
L
ProblemCheck methodThe key-reminder The seat belt warning function l
Check the door switch.
warningdoesn’t is OK.(Refer to GROUP 42-Door Assembly.)
sound.The seat belt warning also l Check the buzzer.
doesn’t function.(Refer to GROUP 52A-Seat Belt.)
The seat belt warn-The seat belt warning light lCheck the seat belt switch.
ing doesn’t
func- flashes.(Refer to GROUP 52A-Seat Belt.)
tion.The seat belt warning light l Check the key-reminder switch.
also does not function (and(Refer to GROUP M-Ignition Switch.)
the key-reminder warning
also does not function).
The buzzer doesn’t stop even through the driver’slCheck the seat belt switch.
seat belt has been buckled.(Refer to GROUP 52A-Seat Belt.)
The seat belt warning light doesn’t flashes (but thelCheck the light bulb.
buzzer sounds).lCheck the key-reminder switch.(Refer to GROUP 54-Ignition Switch.)
lCheck the seat belt switch.
(Refer to GROUP
52A-Seat Belt.)
The warning light does not flash and the warninglCheck the ignition switch input signal.buzzer also does not sound.(Refer to GROUP 52A-Troubleshooting.)l Check the key-reminder switch.
(Refer to GROUP 54-Ignition Switch.)
lCheck the seat belt switch.
(Refer to GROUP 52A-Seat Belt.)
The warning light flashes, but the warning buzzer l
Check the key-reminder switch.
does not sound.(Refer to GROUP M-Ignition Switch.)lCheck the seat belt switch.
(Refer to GROUP 52A-Seat Belt.)
[ TSB Revision
Page 574 of 738
Downloaded from www.Manualslib.com manuals search engine 54-78CHASSIS ELECTRICAL - Lighting System
OPERATION
Battery voltage is always applied to the dome light. When the dome light switch is turned to “ON”,
the dome light will remain lit. After either door is opened if the dome light switch is at “DOOR” position,the dome light will come on.
lWith the dome light turned on (with the ignition switch in the OFF position and with the dome light
switch in the DOOR position), close all doors, and the timer circuit in the ETACS unit will be activatedto gradually vary the voltage for approx. 6 seconds owing to the duty control, and the voltage will
be output to transistor Tr. Since the voltage applied to the dome light gradually decreases, the dome
light will be dimmed.lIf the ignition switch is turned to “ON” while the dome light is lit (while the timer is activated), the
timer circuit will be opened to turn “OFF” transistor Tr. This will immediately turn off the dome light
without dimming.
With the ignition switch in the OFF position, open any door, and all lights will come on.
l
With all lights turned on (with the ignition switch in the OFF position), close all doors, and the timercircuit inside the ETACS unit will operate in the same manner as the dome light to dim all lights.
When the ignition switch is placed in the ON position with all lights turned on (with the timer in operation),the same operation as the dome light will take place.
TROUBLESHOOTING HINTS
Phenomenon
Dome light does not come on
when
a door is opened with the
dome light switch in the DOOR
position.
Check the door switch input signal.
Check the door switch. (Refer to GROUP 42 -
The foot lights and ignitionl
key cylinder illumination
Check the dome light switch.
light illuminate.
lCheck the dome light bulb.
Dome light, foot lights and ignition key illumination light go out
l
at once when doors are closed.Check the door switch input signal.(Refer to P.54-80.)Even if ignition switch is turned on while lights are being
l
dimmed,lightsdo notout at the same time.
Check the ignition switch input signal.
go
(Refer toP.54-80.)
COMPONENT LOCATION
Data ‘link
connect&
TSB Revision
Page 585 of 738
Downloaded from www.Manualslib.com manuals search engine 1. When operation is normal
l
When the ignition switch is switched to the
ON position, battery voltage is applied (viathe multipurpose fuse (11) and hazard
switch) to the turn-signal and hazard flasher
unit.l
When the turn-signal switch is switched to
the LH position,
Trl (within the flasher unit)
is switched ON and OFF repeatedly.
Then the contacts of the relay 1 (also within
the flasher unit) repeatedly switch from ON
to OFF, causing the turn-signal lights and
turn-signal indicator light LH to flash.l
When the turn-signal switch is switched to
the RH position, Tr2 (within the flasher unit)
is switched ON and OFF repeatedly.Then the contacts of relay 2 (also within
the flasher unit) repeatedly switch from ON
to OFF, causing the turn-signal lights and
turn-signal indicator light RH to flash.2. If one of the bulbs is burned out
lIf the LH (or RH) turn-signal light bulb is
burned-out, the resistance of the turn-signalcircuit as a whole increases, resulting in
Lshorter ON and OFF intervals of the LHTrl (or RH Tr2) and a higher flashing rateof the LH lights (or RH lights).CHASSIS ELECTRICAL
- Lighting System54-89
TURN-SIGNAL LIGHT AND HAZARD
L
LIGHT
OPERATION
ed to the “ON” position, the relay contactof the turn signal and hazard flasher unit
is switched ON and OFF repeatedly, in thesame manner as for the operation of the
turn-signal lights, and the left and right turn-
signal lights and turn-signal indicator lights
simultaneously flash repeatedly.
NOTE
(1) The number of flashes of the hazard-warn-
ing lights does not change if there is dam-
aged or disconnected wiring of one light.
(2)The light automatic shut-OFF system is valid
for the illumination light of the hazard switch.(Refer to
P.54-37.)
TROUBLESHOOTING HINTS
1.The turn-signal lights and hazard-warning lightsdo not operate at all.
l Check the hazard switch contact (power
supply side).l Check the turn-signal and hazard flasher
unit.2. All turn-signal lights at the left (or right) side
do not function.
(1) The hazard-warning lights function normal-
ly-lCheck the hazard switch contact (turn-
signal side).l Check the turn-signal switch.
3.The number of flashes of the turn-signal lights
is excessive.l Check the bulbs.
4. The hazard-warning lights do not function.
(1) The turn-signal lights function normally.l
Check the hazard switch contact (haz-
ard-warning light side).
NOTE
For the troubleshooting hints of the automatic lightshut-OFF system, refer to
P.54-37.
COMPONENT LOCATION
TSB Revision