engine removal MITSUBISHI 3000GT 1995 2.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 54-I 18CHASSIS ELECTRICAL - HornHORN SWITCH
REMOVAL AND INSTALLATION(UP TO 1993 MODELS)
~
Y16FO207Removal steps
1. Air bag module (Refer to GROUP 528
(FROM 1994 MODELS)
- Air Bag Module and Clock Spring.)2. Horn contact switch3. Horn contact plate and wire4. Horn switchThe
horn switch is not supplied
If it is faulty, replace the steeringby itself.wheel assembly.i-.
-L 16FOO61200002400
RELAY
INSPECTION
HORN RELAY CHECK
Connect battery to terminal 1 and check continuity between
terminals with terminal 3 grounded.
~1
THEFT-ALARM HORN RELAY CHECK
Connect battery to terminal 2 and check continuity between
terminals with terminal 4 grounded.TSB Revision

Downloaded from www.Manualslib.com manuals search engine LCHASSIS ELECTRICAL
- Cigarette Lighter
CIGARETTE LIGHTER
REMOVAL AND INSTALLATION54-I 23
i,
216FO274
Removal steps
1. Console side cover (RH)2. Plug3. Fixing ring4. Socket case
5. Plate6. Socket7. ProtectorINSPECTION
l Take out the plug, and check for a worn edge on the
element spot connection, and for shreds of tobacco or
other material on the element.
lUsing an ohmmeter, check the continuity of the element.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-186
CHASSIS ELECTRICAL - Radio and Tape Player
RADIO REMOTE-CONTROL
REMOVAL AND INSTALLATION
CAUTION: SRSBefore removal of air bag module, refer to GROUP 52B -Service Precautions and Air Bag Module and Clock Spring.
When removing and installing the remote control switch,
don’t allow any impact or shock to the air bag module.cup to 1993 models>

2.5 Nm1.8 ft.lbs.
Removai steps
1. Air bag module (Refer to GROUP
528 -Air Bag Module and Clock Spring.)
2. Radio remote control switchRADIO AND TAPE PLAYER
REMOVAL AND INSTALLATION2 4
Vehicle without

Z16FO49100002403
Removal steps
1. Radio panel2. Radio and tape player
3. CD player4. Radio bracket5. Front console assembly (Refer to GRbUP
52A - Console Box.)
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Plaver54-I 87
SPEAKER
L/REMOVAL AND INSTALLATION~

,/$‘I./$I/’ j/$/” 1
4./’I:” .,I’/,,$’ ,A’I ._.?,*:. . .;I_I‘7..
,, .-Y_.,: ,’

16FOO9700002404
Door speaker removal steps1. Door trim (Refer to GROUP 42
- DoorTrim and Waterproof Film.)
2. Speaker garnish
3. Speaker
4. Speaker cover
Rear speaker removal steps
1. Quarter trim (Refer to GROUP 52A -Trims.)
2. Speaker garnish
3. Speaker4. Speaker box
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-188CHASSIS ELECTRICAL - Radio and Tape Player
MOTOR ANTENNA
/ ANTENNA FEEDER CABLE / AMPLIFIER
REMOVAL AND INSTALLATION

Motor antenna removal stepsl Rear side trim (LH)
(Refer to GROUP 52A
- Trims.)
1. Ring nut
2. Base
3. Antenna pole
4. Antenna feeder cable and motor antenna
connection5. Motor antenna
Amplifier removal
il. Amplifier (under passenger’s seat)
NOTE
l ‘: Refer to GROUP 52A - Trims‘*: Vehicels with glass mounted antenna
\Z16FO4974
Antenna feeder cable removal stepsl Rear side trim
(LH)*ll Quarter trim (LH)”
l Rear side trim*‘, **l Quarter trim (LH)*t, **l Quarter upper trim”, l *0 Liftgate upper trim*‘, +*l Ligate side trim (RH)“, l *l Rear console assembly(Refer to GOUP 52A - Console Box.)l Radio and tape player(Refer to P54-176)4. Antenna feeder cable and motor antennaconnection6. Rear seat cushion7. Rear seatback8. Inner seat belt
9. Console side cover (LH)
10. Antenna fedder cable
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-I 89
Antenna going downAntenna going up
16FO203
16F019800002406
REMOVAL SERVICE POINT
+A,REAR SEAT CUSHION REMOVAL
Raise and remove the seat cushion with the lever pulled.
INSTALLATION SERVICE POINT
.AqREAR SEAT CUSHION INSTALLATION
(1) Securely fit the attachment wire of the seat cushion
under the seatback.
(2) Pass the inner seat belt buckles through the cushion.
(3) Securely fit the lock plates of the seat cushion into
the holes in the floor.
INSPECTION
ANTENNA MOTOR INSPECTION
Disconnect the motor antenna control unit connector, connect
the positive terminal of the power supply to terminal (1) and
connect the negative terminal to terminal (4) to check that
the antenna goes up, and that when the connections are re-
versed, the antenna goes down.
MOTOR ANTENNA CONTROL UNIT INSPECTION
(1) Connect the harness connector to the motor antenna.
(Body harness)
(2) Disconnect the antenna motor connector.
(3) With the ignition switch in the ACC or ON position, operate
the radio switch and check the voltage between the termi-
nals during the period when the antenna is going up or
going down.
I
I
Antenna operating
directionTerminals to checkVoltage (V)
I
Down
UPl-310-13
3-410-13
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-I 91
LCD AUTO CHANGERREMOVAL AND INSTALLATION
Z16FO49500002408
L
Removal steps
1. CD changer coverl Lu gage compartment floor carpet,big\ floor center board.2. CD auto changer
3. CD changer bracket (front)
4. CD changer bracket (rear)
TSB Revision