clock MITSUBISHI CARISMA 2000 1.G User Guide

FOR PLEASANT DRIVING
6–29
H11D094a
Roof antennaEH11DAJa
To remove the roof antenna, turn it counter-
clockwise.
CAUTION
Be sure to remove the roof antenna
before entering an automatic car
wash or other low-roofed area.
NOTE
Be sure to remove the antenna in the follow-
ing cases:

When entering a place with low clear-
ance.

When going into an automatic car wash.

When placing a car cover over the ve-
hicle.
H16A357a
VentilatorsEH16AASc
1-Centre ventilators
2-Side ventilators
Centre
H16A180a
Air flow and direction
adjustments
3-Ventilator dial
4-Knob
– Open
– Close

FOR PLEASANT DRIVING
6–31
2-Blower speed selection dial
There are 4 blower speeds for control
of the amount of air flow.
Adjust the blower speed by turning the
blower speed selection dial clockwise
or anticlockwise. The setting for ordi-
nary use should be the first or second
speed.
3-Temperature control dial
The heater will not operate if the dial is
set all the way to the left.
The air flow temperature will gradually
increase as the dial is turned to the
right.
NOTE
When the engine coolant temperature is
low, temperature of air introduced into the
passenger compartment does not change
even if the temperature control dial is
moved to the high temperature side.
H04A013a
Mode selectionAir outlets
B
B, C, D
A*, B*, C, D
A, B*, C, D
A, B*
A: From front and side demister
B: From centre and side ventilators
C: From under the instrument panel
D: From under the front seat
* : means a small amount of air flow
4-Mode selection dial
Main flow directions:
(Face position)
Air flows to the upper part of the
passenger compartment.
(Foot/face position)
Air flows to the upper part of the
passenger compartment, and the
leg area.
(Foot position)
Air flows to the leg areas.
(Foot/demister position)
Air flows to the leg areas, wind-
screen door windows.
(Demister position)
Air flows to the windscreen and the
door windows.
NOTE
Air always flows out from the centre and side
ventilators regardless of the mode selection
dial position.

FOR PLEASANT DRIVING
6–32
5-Air selection switch
Every time the switch is pressed, alter-
ation is made between outside air
introduction and inside air recircula-
tion.
When inside air is recirculated, the in-
dicator lamp comes on.
(Outside position)
Outside air is introduced into the
passenger compartment.
(Recirculation position)
Air is recirculated inside the pas-
senger compartment.
NOTE
Normally, use the outside position to keep
the windscreen and side windows clear
and quickly remove fog or frost from the
windscreen.
If high cooling performance is desired or if
the outside air is dusty or otherwise con-
taminated, use the recirculation position.
But in this case, switch to the outside posi-
tion periodically to ventilate so that the win-
dow does not become fogged up.
CAUTION
Use of the recirculation position for
extended time causes the windows to
fog up.
LHD
H03B079a
Leg area heatingEH03BABe
Set the mode selection dial to the position
shown in the illustration and set the air selec-
tion switch (A) to the outside position.
Adjust the temperature by turning the tem-
perature control dial clockwise or anticlock-
wise.
Select the desired blower speed.
NOTEWhen the maximum heating is needed, set
the blower speed at 3rd position.
RHD
H03B056a

FOR PLEASANT DRIVING
6–35
LHD
H03E059a
Introduction of outside airEH03E-Rc
To introduce air into the vehicle during hot
weather, set the air selection switch (A) to the
outside position and set the temperature
control dial to the position shown in the il-
lustration. Be sure to set the temperature
control dial all the way to the left.
Select the desired blower speed.
NOTE
Turn the mode selection dial clockwise and
air will flow to the leg area and the wind-
screen.
RHD
H03E041a
LHD
H04F071a
Cooling
(Vehicles with air conditioning)
EH04FAHe
Set the mode selection dial to the “” posi-
tion.
Set the air selection switch (A) to the outside
position and push the air conditioning switch
(B).
Adjust the temperature by turning the tem-
perature control dial clockwise or anticlock-
wise. Select the desired blower speed.
NOTEIf the outside air is dusty or otherwise con-
taminated, or if high cooling performance is
desired, set air selection switch to the recir-
culation position and the temperature control
dial all the way to the left.
Switch to the outside position periodically to
increase ventilation so that the windows do
not become fogged up.

FOR PLEASANT DRIVING
6–40
H14E019a
Change of air selectionEH14E - Fd
Every time the air selection switch is
pressed, alteration is made between outside
air introduction and inside air recirculation.
When inside air is recirculated, the indicator
lamp (A) comes on.
(Outside position)
Outside air is introduced into the pas-
senger compartment.
(Recirculation position)
Air is recirculated inside the passenger
compartment.Normally, use outside position to keep the
windscreen and side windows clear and
quickly remove fog or frost from the wind-
screen.
If high cooling performance is desired, or if
the outside air is dusty or otherwise contami-
nated, use the recirculation position. Switch
to the outside position periodically to in-
crease ventilation so that the windows do not
become fogged up.
CAUTION
Use of the recirculation position for
extended time may cause the win-
dows to fog up.
H14C126a
Change of the blower speedEH13F-N
Adjust the blower speed by turning the
blower speed selection dial clockwise or
anticlockwise.
The blower speed will gradually increase
as the dial is turned to the right.

FOR PLEASANT DRIVING
6–42
H03D172a
-For quick demisting
1-Set the mode selection dial to the “
”
position.
2-Set the blower speed to the maximum
blower speed position.
3-Set the temperature to the maximum
temperature position.NOTE
(1) While the mode selection dial is set to
the “
” position, the air conditioning
will operate automatically and the out-
side air position will also be selected
automatically. This is done for opti-
mum performance.
(2) To demist effectively, direct the air flow
from the side ventilators toward the door
windows.
(3) Do not set the temperature control dial
around the max. cool position. Cool air
will blow against the window glasses
and form mist on them.
H04F113a
CoolingEH04FAGe
Set the mode selection dial to the “” posi-
tion.
Set the air selection switch (A) to the outside
position and push the air conditioning switch
(B).
Adjust the temperature by turning the tem-
perature control dial clockwise or anticlock-
wise. Select the desired blower speed.
NOTE
If the outside air is dusty or otherwise con-
taminated, or if high cooling performance is
desired, set air selection switch to the recir-
culation position and the temperature control
dial all the way to the left.
Switch to the outside position periodically to
increase ventilation so that the windows do
not become fogged up.

FOR EMERGENCIES
8–27
Hatchback
N10B173a
6-Rear turn - signal lamps
21W (PY21W) . . . . . . . . . . . . . . . . . .
7-Reversing lamps 21W (P21W). . . . .
8-Licence - plate lamps 5W (W5W). .
9-Tail lamps 21/5W (P21/5W). . . . . . .
10-Stop lamps (Hatchback)
21W (P21W) . . . . . . . . . . . . . . . . . . . .
Stop and tail lamps (Sedan)
21/5W (P21/5W) . . . . . . . . . . . . . . . .
11-Rear fog lamp 21W (P21W). . . . . . .
12-High mounted stop lamp 5W (W5W)
Inside
Front room lamps 10W. . . . . . . . . . . . . . . .
Spot lamps*
Vehicles without sunroof 10W. . . . . . . .
Vehicles with sunroof 5W. . . . . . . . . . .
Luggage compartment lamp 10W. . . . . . . .
Sedan
N10B171aN10C046a
Headlamps and position lampsEN10CAHd
Remove the sealing cover by turning it
anti clockwise and disconnect the connector.

FOR EMERGENCIES
8–28
N10C123a
Headlamps
Unhook the spring which secures the bulb,
and then remove the bulb.
N10C086a
CAUTION
Never hold the halogen lamp bulb
with a bare hand, dirty glove, etc.
The oil from your hand could cause
the bulb to break the next time the
headlamps or position lamps are op-
erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner,
etc., and refit it after drying it thor-
oughly.
N10C048a
Position lamps
Remove the lamp socket by turning it
anti clockwise, then pull out the bulb from the
socket.

FOR EMERGENCIES
8–29
N10F055a
Front turn–signal lamps
Petrol–powered vehicles,
Diesel–powered vehicles (right side)
EN10FANc
Turn the bulb socket anticlockwise to re-
move. And remove the bulb from the socket
by turning anticlockwise while pressing it in-
ward.
N10F054a
Diesel–powered vehicles
(left side)
1. Remove the cover.
N10F048a
2. Turn the bulb socket anticlockwise to
remove it. And remove the bulb from
the socket by turning anticlockwise
while pressing it inward.

FOR EMERGENCIES
8–30
N10E002a
Side turn - signal lampsEN10E-Gd
Insert a straight blade (or minus) screwdriver
at the edge of the lens, remove the socket
assembly and bulb together by turning it anti-
clockwise, and then remove the bulb by pul-
ling out.
NOTEWrap a piece of cloth around the straight
blade (or mines) screwdriver in order to
avoid scratching the lens and the body.
N10X035a
Front fog lamps*EN10X - Oc
Remove the cover mounting screw.
N10X036a
Remove bolts (1) and (2) with a screwdriver,
and pull the lamp body towards you.
NOTE
Do not turn the aiming adjusting bolt (3).