water pump MITSUBISHI CARISMA 2000 1.G Owners Manual

STARTING AND DRIVING
5–28
Anti–lock brake system
(ABS)*
EI24ACA
Environmental conditions can have an effect
on braking. During sudden braking when
there is snow, ice, oil, water etc. on the road
surface, a skid may occur. I n this situation,
steering control and braking effectiveness is
reduced and the stopping distance is in-
creased. The vehicle may also go into an un-
controlled spin.
The ABS helps prevent the wheels from
locking during braking, thus maintaining
directional stability, ensuring controllability
and providing optimum braking force.
Driving hints
(1) With ABS fitted, steering during sudden
braking (when the ABS functions) differs
slightly from when the brakes are not
being applied.
Steer the vehicle carefully in these
conditions.(2) Always maintain the same distance
from the vehicle in front of you as you
would for a vehicle not equipped with
ABS. Compared with vehicles not fitted
with ABS, your vehicle may require a
longer stopping distance in the following
cases:

Driving on gravel or snow–covered
roads.

Driving with tyre chains installed.

Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.

Driving on bumpy roads or other
poor driving surfaces.
(3) Operation of ABS is not restricted to
situations where brakes are applied
suddenly. This system may also oper-
ate to prevent wheel lock when you are
driving over manholes, steel road–work
plates, or the vehicle is driven over
steps or level differences in the road,
road markings, or other surfaces which
are difficult for the wheels to grip.
(4) When the ABS is activated, you may
feel the brake pedal pulsating and hear
a characteristic noise. Also at this time,
it may feel as if the pedal attempts to re-
sist being depressed.
In this situation, to let the ABS work
for you, just hold the brake pedal
down more firmly. Do not pump the
brake. This will result in reduced
braking performance.
CAUTION
(1) Even the ABS can not prevent the
natural laws of physics from act-
ing on the vehicle. It cannot for in-
stance avoid accidents that may
result from excessive speed on
bend or following another vehicle
too closely, or aquaplaning. It
should remain the driver’s task to
observe safety precautions to
judge speeds and brake applica-
tions correctly in such condi-
tions.
(2) Be sure to use tyres of the same
type and size on four wheels.
If tyre types or sizes are mixed,
ABS may not function normally.
(3) Never install a limited slip differ-
ential, which is not MITSUBISHI
Genuine parts, as the ABS may
not function normally.
Please consult an authorized
MITSUBISHI dealer.

FOR EMERGENCIES
8–2
If the vehicle breaks downEN40B-Bc
If the vehicle breaks down on the road, move
it to the shoulder and use the hazard warning
flashers.
If the engine stops/fails
Vehicle operation and control are affected if
the engine stops. Before moving the vehicle
to a safe area be aware of the following:
1. The brake booster becomes inoperat-
ive and the pedal effort will increase.
Press down the brake pedal harder
than usual.
2. Since the power steering pump is no
longer operative, the steering wheel
feels heavy when turning it. Turn the
wheel with more effort than usual.
Operation under adverse
driving conditions
EI43ABAa
If your vehicle is stuck: in sand,
mud or snow
If the vehicle becomes stuck in snow, sand,
or mud, it can often be moved by a rocking
motion. Move the gearshift lever or selector
lever alternately between the 1st and Re-
verse position (with manual transmission),
the “L” (LOW) and “R” (REVERSE) position
(with INVECS–II 4A/T), and the Sport mode
and “R” (REVERSE) position (with INVECS–
II Sport Mode 4A/T) while applying slight
pressure to the accelerator pedal.
Avoid racing the engine or spinning the
wheels. Prolonged efforts to free a stuck ve-
hicle may result in overheating and trans-
mission failure. Allow the engine to idle for a
few minutes to let the transmission cool be-
tween rocking attempts.
If the vehicle remains stuck after several
rocking attempts, seek other assistance.
WARNING
When attempting to rock your vehicle
out of a stuck position, be sure that
the area around the vehicle is clear of
people and physical objects. The
rocking motion may cause the ve-
hicle to suddenly launch forward or
backward causing injury or damage
to nearby people or objects.
On a flooded road
(1) Avoid flooded roads. Water could enter
the brake discs, resulting in temporarily
ineffective brakes. In such cases, lightly
depress the brake pedal to see if the
brakes operate properly. If they do not,
lightly depress the pedal several times
while driving in order to dry the brake
pads.
(2) When driving in rain or on a road with
many puddles a layer of water may form
between the tyres and the road surface.
This reduces a tyre’s frictional resis-
tance on the road, resulting in loss of
steering stability and braking capability.
To cope with this, observe the following
items:
(a) Drive your vehicle at a slow speed.
(b) Do not drive on worn tyres. Always
maintain the specified tyre inflation
pressures.

FOR EMERGENCIES
8–21
N07A017a
Bleeding the fuel system
(diesel-powered vehicles
only)
EN07A-Ma
The fuel system should be bled to remove air
as described below if the fuel supply is ex-
hausted during travel.
1. Undo the four clips on the air cleaner
and push the cover (B) aside.
N07A018a
2. Press the pump (A) against the brack-
et (C) with your fingers until the pump
becomes stiff. Then pump several
times more to pressurize the system.
3. Finally, start the engine and check for
leakage of fuel.
If in doubt, consult your nearest autho-
rized MITSUBISHI dealer.
CAUTION
(1) Do not smoke or have any other
open flame near the vehicle while
bleeding the fuel system.
(2) Be sure to carefully clean away
any spilt fuel which could ignite
and cause a fire.
N07B023a
Removal of water from the
fuel filter (diesel-powered
vehicles only)
EN07B-Oa
When water has accumulated in the fuel
filter, remove the water as described below.
1. Place a drainage tray under the filter.
2. Connect a hose to the drain plug (A)
and let it hang down into the tray.
3. Loosen the drain plug (A) a few turns
and tighten the drain plug when clean
fuel comes through.
4. Bleed the air (Refer to “Bleeding the
fuel system” on page 8–21).

MAINTENANCE
9–6
Anti–freeze
The engine coolant contains an ethylene
glycol anti–corrosion agent. The cylinder
head and water pump housing are cast alu-
minium alloy, and periodic changing of the
engine coolant is necessary to prevent cor-
rosion of these parts.
Use High–quality Ethylene–glycol includes
coolant.
It has excellent protection against corrosion
and rust formation of all metals including alu-
minium and can avoid clogs in the radiator,
heater, cylinder head, engine block, etc.
Because of the necessity of this anti–cor-
rosion agent, the coolant must not be re-
placed with plain water even in summer. The
required concentration of anti–freeze differs
depending on the expected ambient tem-
perature.CAUTION
(1) Do not use alcohol or methanol
anti–freeze or any engine cool-
ants mixed with alcohol or meth-
anol anti–freeze. The use of an
improper anti–freeze can cause
the corrosion of the aluminium
components.
(2) For effective anti–corrosion and
anti–freeze performance, keep
the anti–freeze concentration
within the range of 45 to 60%.
Concentrations exceeding 60%
will result in a reduction of both
the anti–freeze and cooling per-
formance thus adversely affec-
ting the engine.
(3) Do not top off with water only.
Water by itself reduces the rust–
protective and anti–freeze qua-
lities of the coolant and has a
lower boiling point. It can also
cause damage to the cooling sys-
tem if it should freeze. Do not use
tapwater, or it could cause cor-
rosion and rust formation.
During cold weatherIf the temperatures in your area drop below
freezing, there is the danger that the coolant
in the engine or radiator could freeze and
cause severe damage to the engine and/or
radiator. Add a sufficient amount of anti–
freeze to the coolant to prevent it from freez-
ing.
The engine coolant mixture used at the fac-
tory provides protection against freezing for
temperatures as low as approximately
–30°C. The concentration should be
checked before the start of cold weather and
anti–freeze added to the system if necess-
ary.