tailgate MITSUBISHI COLT 2006 Service User Guide

DOOR
BODY42-13
KEYLESS ENTRY SYSTEM
M2420010000727
The multimode keyless entry system is installed.
There are the following features.
•Transmitter has two buttons (LOCK/UNLOCK).
•The ETACS-ECU is equipped with the integral
receiver and receiving antenna.
•Up to 4 encrypted codes (4 transmitters) can be
registered using M.U.T.-III.
•Answer-back function has been adopted.
•Using the LOCK/UNLOCK buttons, all doors
(including tailgate) can be locked or unlocked and
door mirrors can be retracted or opened.
CONSTRUCTION DIAGRAM
AC405318
AC206461
AC302207
AC402091
AC
ETACS-ECU
(incorporating receiver and antenna)
Electric signal Radio signal
Lock button
Unlock button
Transmitter
• Door lock actuators (lock/unlock)
• Door mirror assembly (unfolding/folding)
• The signal causes the room lamp to flash once when the doors are locked\
, or come on for 15 seconds when unlocked.
• The signal causes the hazard warning lamp to flash once when the doors \
are locked, or flash twice when unlocked.

DOOR
BODY42-14
DESCRIPTION OF STRUCTURE AND
OPERATION
TRANSMITTER•
AC309781 AC309891
AC302207AC
Lock button
Unlock button Three-diamond markIndicator lamp


The tran
smitter is integra t ed in to the master key .
•When eit her butt on is pressed , the tra n smitter
emit
s a radio sig nal re prese n ting a sp ecific ID
code.
•There a r e two butto ns o n th e tra n smitte r; th e lo ck
but
ton and the u n lock bu tton.
•An indicator lamp, which illumina tes when signals
are
transmitt ed, is add ed on t he ke y grip. This
in
dicator lamp informs you of the signa l transmis
-
sion sta t us a nd warns you of flat batt e ry .
•A brilliant silver Three -d ia mond mark is st amped
on
the back side of the key grip to improve
app
earance.
•A signal transmissi on circuit (p rinted circuit ) and
a b
a ttery are ho used in on e ca se. T he ca se is
hou
sed in the key grip, thus improving re sist ance
to wat
e r ing r ess.
•A coin type b a ttery , CR1616 is used in th e trans-
mitter.
•The transmit t er butto n ope ration allows the sys-
tem to operate a s follows:
System operationThe transmitter is operated.
All doors (including the tailgate) are locked.Press the lock button once.
All doors (including the tailgate) are unlocked.Press the unlock button once.
The door mirrors are retracted.Press the lock button once to lock all doors (including
the tailgate), and within 30 seconds press the lock
button twice quickly.
The door mirrors return to the unfold position.Press the unlock button once to unlock all doors, and
within 30 seconds press the unlock button twice
quickly.

DOOR
BODY42-15
ENCRYPTED CODE
AC103090AB
ON
OFF
Transmitter lock or unlock button
Data
code
The figure shows th e co des transmitte d from the
transmitte
r . Every time the butto n is pressed, the
dat
a cod e is transmitted tw ice. Th e encrypte d co de
for user ide
n tification is a comb ination o f 0 and 1,
and more tha
n 1 million dif f erent comb inations are
available. In a
ddition to t he encrypt ed co de, the dat a
code
cont ains a rolling code t hat change s at e a ch
transmission, prot
ecting tran smission code s from
thef
t by coping.
ETACS-ECU (RECEIVER)
•The ET ACS-ECU incorp orates a receiver with a n
ant
enna. T he receiver co mp ares the code sent
thro
ugh t he an tenna from the transmit t er with the
co
de ret a ined in the re ceiver .
•The ET ACS-ECU send s a si gnal only whe n t hose
two codes corre
spon d and the rollin g co de is
ju
dged correct.
•All of tho s e o u tput sign als are processed inter-
nally in the ETACS-ECU.
•A maximum of fou r encr y pted cod e (4 tran smit-
ters) can be re gistered by co nnecting the
M.U.
T . -III t o the d i agn osis co nnector .
FUNCTION FOR CONFIRMING
ET
ACS-ECU (RECEIVER) OUT P UT AND
OPERA
T ION
When the ET ACS-ECU (receiver) send s a sign al to
the
do or lock actua t o r s an d t a ilga te lo ck actua t or , t h e
haza
r d warnin g lamp an d room lamp illumina te, in di
-
cating that the keyless ent ry syste m is activated.
The hazard warn ing lamp answe rback ca n be
switched b
e tween "lock/unlock yes", "lock o n ly yes",
"unlock o
n ly yes" and "non e" with SW S co nfigurat ion
funct
i on*. Th is f eature is fa ctory preset (de f ault ) to
"lock/unlock ye
s".
Using the ad justment function*, th e number of haz-
ard warning lamp a n swerba ck flashing can be
altere
d. As a n initial set t ing a t factory , the haza r d
wa
rnin g lamp an swerb a ck flashes once wh en locked
and twice when
unlo cke d.
NOTE: Using a cust omisation fea t ure, th e hazard
wa
rning lamp answe rback fun c tio n ca n be change d.
Re
fer to GROUP 54B, Customise Function
P.54B-25.
ItemOperation
Doors and tailgate lockedDoors and tailgate unlocked
ETACS-ECU (receiver)Sends lock signalSends unlock signal
Hazard warning lampFlashes once (I nitial setting)Flashes twice (Initial setting)
Flashes twiceFlashes once
Room lampFlashes onceIlluminates for 15 seconds
KEYLESS ENTR Y TIMER LOCK TIME
If any door (includin g the t a ilgat e) is not op ened or
closed within 3
0 se cond s af ter th e doo rs (in c lu ding
the t
a ilgate) a r e unlocked by the keyless ent ry sys
-
tem, ETACS-ECU aut omatically sen d s th e door lock
sign
al to lock the doors (includ i ng t he t a ilgate). T h is
funct
i on p r even t s the d oors (including the t a ilga te)
from b
e ing unlocke d unex pectedly by opera t ion
errors.
Using a customisa t ion fea t ure*, the timer lock
delay ca
n be chang ed to 3 0 , 60, 120, or 180 sec
-
onds. The initial setting at fa ctory is 30 secon d s.
NOTE: *: Using a custo m isation fea t ure, the timer
lock delay can b e ch anged. Re fer to GROUP 54B,
Customise Function
P.54B-25.
OPERA T ION INHIBITION CONDITIONS
The operation of t he keyless entry system is inhibited
in the
following cond itio ns.
•When the ignition key is inse rted into the ignition
sw
itc h .
•When eit her doo r (including th e t a ilg ate) is ope n
(the
door switch : ON). (includin g doo r ajar)
POWER WI NDOW
M24200220 0010 0
The powe r window ha s the following f eatures.
•The power wind ow timer functio n is adopt ed.
•The power wind ow lock switch is adopte d .

WINDOW GLASS
BODY42-18
WINDOW GLASS
M2420015000669
Laminated glass is used for the windshield and rein-
forced glass for the other windows. The window
glasses have the following features.
•UV & heat protect glass has been used for the
windshield as standard.
•The ultraviolet (UV) shield glasses have been
used for the front door window glasses and rear
door window glasses as standard.
•Privacy glasses have been used for rear door
window glasses, quarter window glasses, and
tailgate window glass as an option.
VISIBLE RAY TRANSMISSIVITY RATE FOR WINDOW GLASS
AC401290AC206463AB
1
2 3
45 6
7
No.NameTy p eThick
ness
(mm)ColourVisible ray
transmissivity
rate (%)
1WindshieldLaminated glass
(UV & Heat
protect glass)4.4Green74.4
2Delta window glassTempered glass2.8Green83
3Front door window glass3.1Green (UV shield glass)75
4Rear door window glass3.1Green (UV shield glass)75
Dark grey (privacy glass)25
5Quarter window glass2.8Green83
Dark grey (privacy glass)28
6Tailgate window glass3.1Green83
Dark grey (privacy glass)25
7Sunroof lid glass4.0Dark grey10
NO
TE: The visible ray transmissivity ra t e (%) is a re ference va lue.

GENERAL INFORMATION
CHASSIS ELECTRICAL54A-2
GENERAL INFORMATION
M2540000100302
FEATURES
IMPROVEMENT OF VISUAL OBSERVA-
TION AND SAFETY, AND ENHANCEMENT
OF USER-FRIENDLINESS AND VERSA
-
TILITY
•The large four headlamps with the lightweight
resin lenses have been adopted.
•The high-mounted stop lamp has been installed
on the tailgate for all models.
•Combination meters and ECUs are connected
using CAN to ensure the transmission of informa
-
tion.
•The combination meters are provided integrated
with a perfect round-shaped speedometer where
the needles operate at the wider angle.
IMPROVEMENTS IN SERVICE QUALITY
•Diagnosis connector for inspection with M.U.T.-III
is installed.
•Diagnosis and service data are integrated in the
combination meter, enabling communication with
M.U.T.-III
BETTER PRODUCT PACKAGE
•The smart wiring system (SWS) has been
adopted for the lamp control including the head
-
lamp auto turn-off and fog lamp unattended-oper-
ation reminder.

TECHNICAL FEATURES
GENERAL00-4
TECHNICAL FEATURES
EXTERIORM2000017000825

AC601279AB
1, 2
5
34
6
MAIN CH
ARACTERISTICS
1. The radia tor grille has been ren ewed in shape to
provide the superior and high-quality d esign.
2. A ch rome- plate d emb ellish er has been installed
to e mpha size the feelings of luxury and sporty.
3. The front b umpe r has been re newed in sh ape to
provide the superior and high-quality d esign.
4. The rear bu mper has been re newed in sha pe to
emphasize the sporty image in rear a ppearance
tog ether wit h mo dification in the tailgate glass
and rear comb ination lamp s.
5.Due to the ch ange o f the fron t bumper , the shap e
of f ront fog lamp has been changed.
6.The design o f the rea r combin ation lamp assem-
bly ha s been changed. In add ition, the location s
of t he t ail lamp s have bee n moved u pward to
in crease visibility .

TECHNICAL FEATURES
GENERAL00-28
ENVIRONMENTAL PROTECTION
M2000027000279
Mitsubishi has given careful consideration to protec-
tion of natural resources and the environment in the
vehicle. Environmentally friendly features are shown
below.
IMPROVEMENT ON RECYCLING EFFICIENCY
ClassificationMain Components
Components made
of recycled
materialsChip materials produced during manufacturing process has been reused as the
following components: Door inside handle, bu mper, radiator grille, instrument panel,
door trims, or floor padding.
Waste materials produced by other i ndustries have been reused as the following
components: Engine oil level gauge, air filter casing, and sound absorbing materials
for dash panel
Components made
of materials which
can be easily
recycledThermoplastic resin has been utilised as the following components: Inside door
handle, bumper, radiator grille, instrument panel, door trim
Thermoplastic resin has been utilised as t he following components: Vacuum hose for
engine control, air intake hose, hood weather strip, tailgate opening weather strip
REDUCTION OF MATERIAL BURDEN ON ENVIRONMENT
ItemMain Components
Elimination of
environmental
burden materialsLead-free materials have been utilised as the following components: Radiator, fuel
tank, power steering oil pressure hose, el ectrodeposition paint for body, glass ceramic
print, heater core, battery terminals, wiring harness
Non-asbestos material has been used for engine gaskets.
PVC(polyvinyl chloride)-free materials ha ve been used for the waterproofing film.
Prevention of
ozone depletionAir conditioner filled with new refrigerant (HFC 134a) has been installed.
Prevention of air
pollutionEmployment of a metal cylinder head gasket reduces the volume of incomplete
combustion generated between the cylinder block and cylinder head, and suppresses
the level of unburned hydrocarbon (HC).
SERVICEABILITY AND RELIABILITY
M2000028000528
MULTI USE TESTER-III (M.U.T.-III) SUB
ASSEMBLY
Comprehensive improvements have been made to
the M.U.T.-II, a tester for diagnosing problems with
the electronic control system. For easier servicing,
the newly developed M.U.T.-III has greatly improved
functions and is much easier to use. The M.U.T.-III
expands the functions of the M.U.T.-II in the following
ways:
1.CAN* bus diagnosis
•Auto diagnosis function for the CAN commu-
nications bus line is added.
NOTE: *CAN: Controller Area Network (for further
details, refer to GROUP 54C
P.54C-2).

DIAGNOSTIC FUNCTION
SMART WIRING SYSTEM (SWS)54B-8
DIAGNOSTIC FUNCTION
M2541003000642
DIAGNOSIS CODE SET
For more information about diagnosis code output,
refer to the Workshop Manual.
SWS INPUT SIGNAL CHECK USING
M.U.T.-III
When the M.U.T.-III is connected to the diagnosis
connector and any of the SWS-linked switches is
operated, the PC buzzer sounds to evaluate whether
the switch is normal or not.
SWS INPUT SIGNAL CHECK AND ECU
CHECK BY USING SWS MONITOR
The switch signals sent by ECUs and the operations
of these ECUs can be confirmed by using the SWS
monitor and the M.U.T.-III.
INPUT SIGNALS THAT CAN BE CHECKED
Input signalCondition for sounding buzzerDisplay on
M.U.T.-III (when
SWS monitor is
used)
Ignition switch (ACC)Turn from "LOCK" (OFF) to "ACC" positionfrom OFF to ON
Ignition switch (IG1)Turn from "ACC" to "ON" positionfrom OFF to ON
Key reminder switchRemove the ignition key from ignition key cylinder
(form inserted position)from OFF to ON
Hazard lamp switchTurn from OFF to ONfrom OFF to ON
Fog lamp switch
Remote controlled mirror
switch (unfolding/folding
switch)
Speed signal When the speed changes from less than 10 km/h to
more than 10 km/hDisplays the
vehicle speed
Cranking signalWhile the ignition switch is in START position (while
cranking the engine)−
Selector lever P position signal
(parking)When the selector lever is shifted to the "P" position
(Ignition switch: ON or START)−
Selector lever R position signal
(reverse)When the selector lever is shifted to the "R" position
(Ignition switch: ON or START)−
Buzzer triggered by
ETACS-ECU
*1
When the following conditions are satisfied
•Ignition switch: LOCK (OFF) position
•Lighting switch: ON
•Driver’s door switch: ON (Driver’s door: OPEN)
ON
When requirements for sounding each warning buzzer
are not satisfiedOFF
Door switchDriver’s doorWhen door(s) or tailgate is opened from the closed
positionfrom OFF to ON
Passenger’s
door
Rear door
All door switchA door is opened when all the doors are closedfrom OFF to ON

ECU FUNCTIONS AND CONTROLS IN THE SWS
SMART WIRING SYSTEM (SWS)54B-12
BUZZER
LAMP REMINDER BUZZER FUNCTION
AC208400AB
Tail lamp, headlamp
or fog lamp
Driver's
door switch
Buzzer
output
ON
OFF
ON (Open)
OFF (Closed)
ON (Buzzer sounds) OFF (Buzzer does not sound)
When th e ign i tio n ke y is removed and th en the
driver's d
oor is ope ned with turn ing ON the t a il lamp ,
fog la
mp o r head lamp, the b u zzer so unds con t inu
-
ously to alert the driver t hat the lamp is still ON.
However, if t he t a il lamp or th e headlamp is tu rned of f
by th
e head lamp auto m atic-shut down functio n , the
buzzer doe
s no t sou nd.
DOOR-AJAR WARNING BUZZER
FUNCTION (THE INIT
IAL CONDITION:
WITH FUNCTION)
AC101625AD
0 km/h 8 km/h
(Closed) OFF
(Opened) ON ON
OFF
Door or
tailgate
switch
Vehicle speed
Buzzer
output OFF
(Does not sounds) (Sounds) ON
Ignition switch
If the
ve hicle speed se nt fro m t he comb ination meter
via
CAN communication exceed s 8 km/h when a
door is op
en for o ne se cond or more, the
ET
ACS-ECU makes the door ajar in dicator lamp
flash 16 times and
activate s the buzzer (b eepin g 16
time
s) to inform the driver that a door is o pen.
NOTE: Av ailability of the door -a jar alarm function
can b
e
se lected by the cust omize fu nction (Refer to
P.54B-25).
Interio r lampInterior lamp dimme r cont rol fun c tionETA C S-ECUP.54B-23
Ignition ke y cylinder illuminatio n lamp
control functionP.54B-24
Door-ajar indicatorP.54B-24
Customize functionETA C S-ECURefer to
P.54B-25.
Function C ontrol ECU Function
descriptio n

CUSTOMISE FUNCTION
SMART WIRING SYSTEM (SWS)54B-25
CUSTOMISE FUNCTION
M2541006000243
Using M.U.T.-III adjusts the following function. The
programmed information is held even when the bat
-
tery is disconnected.
•Vehicle speed-dependent wiper function
With the windshield wiper switch in the intermittent
position, the intermittent duration changes
depending on the intermittent adjusting knob
position and the vehicle speed.
•The selector "P" position-linked central door
unlocking function
When the selector lever is shifted to the "P" position,
all the doors unlock.
•Turn-signal lamp operation sound function
Synchronized with the hazard lamp and the turn sig-
nal lamp, the buzzer sounds.
•Dimmer interior lamp control duration
When the door is closed with the ignition switch
LOCK (OFF), the interior lamp is turned OFF
automatically in the specified time.
•Timer lock time after executing the keyless entry
unlock
If any door including a tailgate is not opened after
being unlocked with the keyless transmitter,
doors are locked automatically within the speci
-
fied time.
•Door-ajar warning function
Driving with any door, including a tailgate, not prop-
erly closed sounds the buzzer to let the driver
know the door-ajar state.
•Rear wiper intermittent duration
When the rear wiper switch is turned ON, the rear
wiper operates in the intermittent action. When
the rear wiper switch is turned from OFF to ON
two cycles, the rear wiper makes continuous
operation regardless of the intermittent operation
duration setting.
•Wiper linked with washer function
When this function is active, the windshield wiper
operates if the washer switch is turned ON.
•Hazard answer back function of the keyless entry
system
When lock/unlock is operated with the keyless entry
transmitter, the horn sounds so that the driver can
recognize the lock/unlock status of the vehicle
even if the driver is away from it.
•Initialising all functions (Returning to the initial
condition)
All adjusting functions are returned to the settings at
the time of factory shipment.
Item
No.Items shown
on M.U.T.-III
screenItemAdjustment items
shown on M.U.T.-III
screenAdjusting contents
4SPEED SEN
WIPVehicle
speed-dependent
wiper functionW.FUNCTIONWith function (Initial setting)
W/O FUNCTIONWithout function
9KEYLESS(HA
ZD)Hazard answer
back function of
the keyless entry
systemLOCK/UNLOCKWith function for lock/unlock (the initial
condition)
LOCKEDWith function only for lock
UNLOCKEDWithout function only for unlock
W/O FUNCTIONWithout function
14P UNLOCK
ACT.Door unlock
function linked
with "P" position
shift for centre
door lock systemW.FUNCTIONWith function
W/O FUNCTIONWithout function (the initial condition)
15T/SIG.BUZZE
RTurn-signal lamp
operation sound
functionW.FUNCTIONWith function
W/O FUNCTIONWithout function (the initial condition)