engine MITSUBISHI COLT 2008 (in English) User Guide

Instruments and controls3-5
3
Tripmeter
The tripmeter indicates the dist ance travelled during a particu-
lar trip or period.
There are two tripmeter displays: TRIP and .
TRIP can be used to measur e the distance travelled since
the current trip began. At the same time, TRIP can be used
to measure the distance from an intermediate location.
Every time the reset button (C) is pressed lightly (less than 1
second), tripmeter indications (TRIP and ) are changed. To reset the tripmeter
To return the display to “0”, press the reset button (C) for more
than 1 second. Only the currently displayed value will be reset.
If TRIP is displayed, for example, only TRIP will be
reset.
NOTE
●
Display TRIP and each have a maximum distance
of 9999.9 km or mile.
● Even when the engine has been stopped, the odometer/trip
odometer indication is given for about 30 seconds if any
of the following steps is taken.
• The ignition key is turned to the “OFF” position.
• Any door is opened.
• The odometer/trip odometer reset button is pressed.
● When disconnecting the batter y terminal for a long time,
the memory of tripmeter display TRIP and are
cleared, and the display returns to “0”.
TRIP
TRIP

Instruments and controls3-7
3
Indicator and warning lamps
E00501501324
1- Electric power steering warning lamp
→ P. 4-41
2- Supplemental restraint system (SRS) warning lamp →
P. 2 - 7 0
3- High coolant temperature warning lamp → P. 3-13
4- Low coolant temperature indicator lamp → P. 3-8
5- Turn-signal indicator lamps/Hazard warning indicator lamps → P. 3-8
6- Brake warning lamp → P. 3-9
7- Anti-lock brake (ABS) warning lamp → P. 4-38
8- High-beam indicator lamp → P. 3-8
9- Front fog lamp indicator lamp* → P. 3-8
10- Rear fog lamp indicator lamp → P. 3-8
11- Low fuel warning lamp → P. 3-6
12- Door-ajar warning lamp → P. 3-13 13- Traction control system (TCL)/Active stability control sys-
tem (ASC) indicator lamp* → P. 4-44
14- Seat belt warning lamp* → P. 2 - 2 5
15- Front passenger’s air bag off indicator lamp* → P. 2-56
16- Allshift indicator display (vehicles with automated manual transmission) → P. 4-26
17- Oil pressure warning lamp → P. 3-12
18- Charge warning lamp → P. 3-12
19- Check engine warning lamp → P. 3 - 1 1
20- Diesel preheat indicator lamp (diesel-powered vehicles) → P. 3-9

3-8 Instruments and controls
3Indicator lamps
E00501600012
Turn-signal indicator lamps/Hazard
warning indicator lamps
E00501700042
These indicator lamps blink on and off when a
turn-signal lamp is operating.
NOTE●
If the blinking is too fast, the cause may be
a faulty turn-signal connection or a blown
lamp bulb.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash on and
off continuously.
High-beam indicator lampE00501800072
This indicator lamp illuminates when the high
beam is used.
Front fog lamp indicator lamp*E00501900158
This indicator lamp illuminates while the front
fog lamps are on.
Rear fog lamp indication lampE00502000084
This indication lamp illuminates while the rear
fog lamp is on.
Low coolant temperature indicator
lamp
E00502200028
When the engine coolant temperature is low, this
indicator lamp illuminates and then goes out
when the temperature rises to roughly 40 °C or
more.
NOTE● When the indicator lamp goes out, this
should be used as a rough indication of
when the heating starts working.
● If the indicator lamp stays illuminated,
there may be a fault in the temperature sen-
sor or other component. We recommend
you to have your vehicle inspected.

Instruments and controls3-9
3
Diesel preheat indication lamp
(diesel-powered vehicles)
E00502300029
This indication lamp illuminates when the igni-
tion switch is placed in the “ON” position. As
the glow plug becomes hot, the lamp goes out
and the engine can be started.
NOTE●If the engine is cold, the diesel preheat indi-
cation lamp is on for a longer time.
● When the engine has not been started within
about 5 seconds after the diesel preheat
indication lamp went out, return the ignition
switch to the “LOCK” position. Then, turn
the switch to the “ON” position to preheat
the engine again.
Wa r n i n g l a m p s
E00502400017
Brake warning lampE00502501099
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after a few seconds. Always make sure that
the lamp goes off before beginning to drive.
With the ignition switch “ON”, the brake warn-
ing lamp illuminates under the following condi-
tions:
● When the parking brake lever has been
engaged.
With the ignition switch “ON”, the brake warn-
ing lamp illuminates and a buzzer sounds under
the following conditions: ● When the brake fluid level in the reservoir
falls to a low level.
● The vehicle speed exceeds 8 km/h with the
parking brake applied.

3-10 Instruments and controls
3
CAUTION!
●If either of the si tuations described
below occurs, there is a risk of reduced
brake effectiveness. Stop the vehicle in
a safe place and we recommend you to
have it checked.
• The brake warning lamp does not illuminate when the parking brake is
applied or does not turn off when the
parking brake is released.
• The brake warning lamp remains
illuminated during driving.
● If the brake warnin g lamp comes on at
the same time as the ABS warning
lamp, the brake force distribution
function may be not working so hard
braking could make the vehicle unsta-
ble. Avoid hard braking and high-
speed driving. Stop the vehicle in a safe
place and we recommend you consult a
MITSUBISHI MOTORS Authorized
Service Point.
● The vehicle should be brought to a halt
in the following manner when brake
performance has deteriorated.
• Depress the brake pedal harder than
usual. Even if the brake pedal moves
down to the very end of its possible
stroke, keep it pressed down hard.
• Should the brakes fail, use engine
braking to reduce your speed and
slowly pull the parking brake lever to
park your vehicle.
Depress the brake pedal to operate
the stop lamp (brake lamp) to alert
the vehicles behind you.
CAUTION!

Instruments and controls3-11
3
Check engine warning lampE00502600918
This lamp is a part of an onboard diagnostic sys-
tem which monitors the emissions, engine and
automated manual transmission control systems.
If a problem is detected in one of these systems,
this lamp illuminates and a buzzer sounds.
Although your vehicle will usually be drivable
and not need towing, we recommend you to have
the system checked as soon as possible.
This lamp will also illuminate for a few seconds
when the ignition switch is turned to the “ON”
position. If it does not go off after a few seconds,
we recommend you to have the vehicle checked.
NOTE● The engine electr onic control module
accommodating the onboard diagnostic sys-
tem has various fault data (especially about
the exhaust emission) stored.
This data will be erased if a battery cable is
disconnected which will make a rapid diag-
nosis difficult. Do not disconnect a battery
cable when the check engine warning lamp
is ON.
CAUTION!
● Prolonged driving with this lamp on
may cause further damage to the emis-
sion control system. It could also affect
fuel economy and drivability.
● If the lamp does not illuminate when
the ignition switch is turned to the
“ON” position, we recommend you to
have the system checked.
●If the lamp illuminates while the
engine is running, avoid driving at
high speeds and we recommend you to
have the system checked.
During vehicle operation with the
lamp illuminated, the vehicle may not
accelerate when you depress the accel-
erator pedal.
CAUTION!

3-12 Instruments and controls
3
Charge warning lampE00502700036
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started.
In the event of a fault in the charging system, the
warning lamp comes on and a buzzer sounds.
Oil pressure warning lampE00502800053
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started. If it illuminates
and a buzzer sounds while the engine is running,
the oil pressure is too low.
If the warning lamp illuminates while the engine
is running, turn the engine off and have it
inspected.
NOTE● The oil pressure warning lamp should not
be treated as an indi cation of the engine’s
oil level. The oil level must be checked
using the dipstick.
CAUTION!
● If the warning lamp illuminates and a
buzzer sounds while the engine is run-
ning, there is a problem in the charg-
ing system. In this case, immediately
park your vehicle in a safe place and
we recommend you to have it checked.
CAUTION!
●If this lamp illum inates when the
engine oil level is not low, have it
inspected.
● This warning lamp does not indicate
the amount of oil in the crankcase.
This must be determined by checking
the oil level on the dipstick, while the
engine is switched off.
● If you continue driving with low engine
oil level or with this warning lamp illu-
minated, engine seizure may occur.

Instruments and controls3-13
3
High coolant temperature warning
lamp
E00503000023
This lamp illuminates and a buzzer sounds if the
coolant temperature beco mes excessively high.
NOTE●The high coolant temperature warning lamp
may illuminate when the vehicle has been
driven at high speeds or on hilly roads. This
flashing does not necessarily indicate a
problem. It should stop if you keep the
engine running for a while or continue driv-
ing the vehicle.
Door-ajar warning lampE00503300215
This lamp illuminates when a door or the tailgate
is either open or incompletely closed.
A buzzer sounds if the vehicle speed exceeds
5 km/h with a door or the tailgate ajar.
CAUTION!
●If the lamp illuminates during vehicle
operation, it indicate s that the engine is
possibly overheating . Continued driv-
ing could make the engine fail. Imme-
diately stop the vehi cle in a safe place
and take appropriate action. (Refer to
“Engine overheating” on page 6-6.)CAUTION!
● Before moving your vehicle, check that
the warning lamp is OFF.

Instruments and controls3-31
3
Combination headlamp
s and dipper switch
E00506000923
Headlamps
NOTE●Do not leave the headlamps and other lamps on for a long
time while the engine is stationary (not running). A run-
down battery could result.
● When it rains, or when the vehicle has been washed, the
inside of the lens sometime s becomes foggy. This is the
same phenomenon as when window glass mists up on a
humid day, and does not indicate a functional problem.
When the lamp is switched on, the heat will remove the
fog. However, if water gathers inside the lamp, we recom-
mend you to have it checked.
Type 1
Rotate the switch to turn on the lamps.
All lamps off
Position, tail, licence plate and instrument panel lamps on
Headlamps and other lamps go on

3-32 Instruments and controls
3
Type 2
Rotate the switch to turn on the lamps.
NOTE●If the front fog lamps (if so equipped) turn on when they
are supposed to with the switch in the “AUTO” position,
the lamps turn off automatically with the engine switch
off.
● Do not cover the sensor (A) for the automatic on/off con-
trol by affixing a sticker or label to the windscreen. Also,
do not put any water-repellent coating on the windscreen.
● If the lamps do not turn on or off with the switch in the
“AUTO” position, manually operate the switch and we
recommend you to have your vehicle checked.
[Vehicles with Daytime Running Lamp]
When the ignition switch is in the “ON” position and the lamp
switch is set to the “ ” (OFF) position, the low beam of the
headlamps, tail lamps, etc., will illuminate.
All lamps off
AUTO With the ignition switch in the “ON” position, head-
lamps, position, tail, licence plate, and instrument panel
lamps turn on and off automatically in accordance with
outside light level. All lamps turn off automatically
when the ignition switch is turned to “OFF” position.
Position, tail, licence plate and instrument panel lamps
on
Headlamps and other lamps go on