brake light MITSUBISHI COLT 2008 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2008, Model line: COLT, Model: MITSUBISHI COLT 2008Pages: 450, PDF Size: 14.57 MB
Page 168 of 450
4-2 Starting and driving
4Economical driving
E00600100763
For economical driving, there ar
e some technical requirements
that have to be met. The prerequisite for low fuel consumption
is a properly adjusted engine. In order to achieve longer life of
the vehicle and the most economical operation, we recommend
that you to have the vehicle checked at regular intervals in
accordance with the service standards.
Fuel economy and generation of exhaust gas and noise are
greatly influenced by personal driving habits as well as the par-
ticular operating conditions. The following points should be
observed in order to minimize w ear of brakes, tyres and engine
as well as to reduce environmental pollution.
Starting
Avoid rapid acceleration and sudden starts; such operation will
result in higher fuel consumption.
Shifting
Shift only at an appropriate speed and engine speed. Always
use the highest gear possible.
City traffic
Frequent starting and stopping increases the average fuel con-
sumption. Use roads with smooth traffic flow whenever possi-
ble. When driving on congested roads, avoid use of a low gear
at high engine speeds.
Idling
The vehicle consumes fuel even when idling. Avoid extended
idling whenever possible.
Speed
The higher the vehicle speed, the more fuel is consumed. Avoid
driving at full speed. Even a slight release of the accelerator
pedal will save a significant amount of fuel.
Tyre inflation pressure
Check the tyre inflation pressure s at regular intervals. Low tyre
inflation pressure increases ro ad resistance and fuel consump-
tion. In addition, low tyre pres sures adversely affect tyre wear
and driving stability.
Load
Do not drive with unnecessary articles in the luggage compart-
ment. Especially during city dr iving, where frequent starting
and stopping is necessary, the increased weight of the vehicle
will greatly affect fuel consum ption. Avoid driving with unnec-
essary luggage, etc., on the ro of; the increased air resistance
will increase fuel consumption.
Cold engine starting
Starting a cold engine consumes more fuel.
Unnecessary fuel consumption is also caused by keeping a hot
engine running. After the engine has started, commence driv-
ing as soon as possible.
Air conditioning*
The use of the air conditioning will increase fuel consumption.
Page 173 of 450
Starting and driving4-7
4
To r e l e a s e
When parking on a hill, apply the parking brake and turn the
front wheels towards the kerb on a downhill grade, away from
the kerb on an uphill grade.
1- Pull the lever up slightly.
2- Push the button at the end of the hand grip.
3- Push the lever downward.
CAUTION!
● Before driving, be sure that the parking brake is
fully released and brake warning lamp is off.
If a vehicle is driven wi thout releasing the parking
brake, the brake will be overheated, resulting in
ineffective brak ing and possible brake failure.
●When you intend to apply the parking brake, firmly
press the brake pedal to bring the vehicle to a com-
plete stop before pullin g the parking brake lever.
Pulling the parking brake lever with the vehicle
moving could make the rear wheels lock up, thereby
making the vehicle unstable.
● If the brake warning lamp does not extinguish when
the parking brake is fully released, the brake system
may be abnormal. For details, refer to “Brake warn-
ing lamp” on page 3-9.
CAUTION!
Page 181 of 450
Starting and driving4-15
4
Steering wheel lock
E00601500445
To l o c k
Remove the key at the “LOCK” position.
Turn the steering wheel until it is locked.
To unlock
Turn the key to the “ACC” position while moving the steering
wheel slightly.
CAUTION!
●
Do not remove the ignition key from the ignition
switch while driving. The steering wheel will locked,
causing loss of control.
●If the engine is stopped while driving, the brake ser-
vomechanism will cease to function and braking
efficiency will deteriorat e. Also, the power steering
system will not function and it will require greater
manual effort to operate the steering.
● Do not leave the key in the “ON” position for a long
time when the engine is no t running, as doing so will
cause the battery to be discharged.
●Do not turn the key to the “START” position when
the engine is running, as doing so could damage the
starter motor.
CAUTION!
●Remove the key when leaving the vehicle.
Page 201 of 450
Starting and driving4-35
4
Braking
E00607000947
All parts of the brake system ar
e critical for safety. We recom-
mend that you have the vehicl e checked at regular intervals
according to the service booklet.
Brake system
The service brake is divided into two brake circuits so that if
one brake circuit fails, the othe r one is available to stop the
vehicle. In this situation, ev en if the brake pedal moves down
to the very end of its possible stroke, keep it pressed down
hard; stop driving as soon as possible and have the brake sys-
tem repaired.
Power brakes
Your vehicle is equipped with power brakes for more braking
force with less brake pedal effort.
Your brakes are designed to oper ate at full capacity, even if the
power assist is not being used.
If the power assist is not being used, the effort needed to press
the brake pedal is greater.
If you should loose the power assist for some reason, the
brakes will still work. If the power brake unit or either
of the two brake hydraulic sys-
tems stops working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to press
the brake down further or harder when slowing down or stop-
ping, or if the brake warning lamp comes on.
Wa r n i n g l a m p
The brake warning lamp will illuminate to indicate a fault in
the braking system. Read “Brake warning lamp” on page 3-9.
When brakes are wet
Check the brake system while dr iving at a low speed immedi-
ately after starting, especially wh en the brakes are wet, to con-
firm they work normally.
A film of water can be formed on the brake discs or brake
drums and prevent normal braki ng after driving in heavy rain
or through large puddles, or after the vehicle has been washed.
If this occurs, dry the brakes out by driving slowly while
lightly depressing the brake pedal.
CAUTION!
● Avoid driving habits that cause heavy braking and
never “ride” the brakes by resting your foot on the
brake pedal while driving.
This causes brake overheating and fade.WARNING!
● Never coast downhill with the engine OFF. Keep the
engine running whenever your vehicle is in motion.
If you turn off the engine while driving, the power
brake booster will stop working and your brakes
will not work as well.
● If the power assist is lost or if either brake hydraulic
system stops working properly, have your vehicle
checked immediately.
Page 202 of 450
4-36 Starting and driving
4
When driving downhill
It is important to take advantage of engine braking by shifting
to a lower shift position while driving on steep downhill roads
in order to prevent the brakes from overheating.
Brake pads and linings
●With new brake pads or linings, avoid where possible sud-
den full application of the brakes for the first 200 km (120
miles) of driving.
● The disc brakes are fitted with a warning device which
emits a shrieking metallic sound while braking if the
brake pads have reached their limit.
If you hear this sound, have the brake pads replaced.
Anti-lock brake system (ABS)
E00607100791
Environmental conditions can ha ve an effect on braking. Dur-
ing sudden braking when there is snow, ice, oil, water etc. on
the road surface, a skid may occur. In this situation, steering
control and braking effectivenes s is reduced and the stopping
distance is increased. The vehicl e may also go into an uncon-
trolled spin.
The ABS helps prevent the wheel s from locking during brak-
ing, thus maintaining directional stability, ensuring controlla-
bility and providing optimum braking force.
Driving hints
● When using the anti-lock brak e system (sudden braking),
steering is slightly different from normal driving condi-
tions. Use the steering wheel carefully.
● Always maintain the same di stance from the vehicle in
front of you as you would for a vehicle not equipped with
ABS.
Compared with vehicles not fitted with ABS, your vehicle
may require a longer stopping distance in the following
cases:
• Driving on gravel or snow-covered roads.
• Driving with tyre chains installed.
• Driving on roads where the road surface is pitted or has
other differences in surface height.
• Driving on bumpy roads or other poor driving surfaces.
WARNING!
●Do not leave any objects ne ar the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that woul d be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
WARNING!
● Driving with worn brake pads will make it harder to
stop, and can cause an accident.
Page 204 of 450
4-38 Starting and driving
4
ABS warning lampE00607200718
The ABS warning lamp comes on and a buzzer sounds in the
event of a malfunction in the anti-lock brake system. It will
also come on as a self-check for a few seconds when the igni-
tion switch is turned to the “ON” position. The lamp goes out
after a few seconds. Always make sure that the lamp goes out
before starting to drive.
If the warning lamp illuminates while drivingE00607300881
If only the ABS warning lamp illuminates
● Avoid hard braking and high-speed driving. Stop the vehi-
cle in a safe place.
Restart the engine and check to see if the lamp goes out
after a few minutes of driving; if it remains off during
driving, there is no problem.
However, if the lamp does not go out, or if it lights up
again when the vehicle is dr iven, we recommend that you
consult a MITSUBISHI MOTORS Authorized Service
Point.
● The ABS warning lamp can illuminate if there is insuffi-
cient battery voltage when the engine is started. In this
case, it does not indicate an ABS fault.
Charge the battery by allowing the engine to idle for a
while.
If the battery has been charged but the ABS warning lamp
continues to illuminate or illuminates intermittently, we
recommend that you cons ult a MITSUBISHI MOTORS
Authorized Service Point.
If the ABS warning lamp and brake warning lamp
illuminate at the same time
● The brake force distribution function may not work, so
hard braking could make the vehicle unstable.
Avoid hard braking and high-speed driving. Stop the vehi-
cle in a safe place and we recommend that you consult a
MITSUBISHI MOTORS Authorized Service Point.CAUTION!
●If the warning lamp stays on or does not illuminate
when you start the vehicle, it indicates that the ABS
is not functioning and that only the standard brake
system is in operation. (I n this condition the stand-
ard hydraulic brake system will still function.) We
recommend that you consult a MITSUBISHI
MOTORS Authorized Service Point.
Page 215 of 450
Starting and driving4-49
4
Operating hints
●Do not let the clutch slip and do not increase the engine
speed more than necessary when starting.
● Be sure that the driving speed does not exceed the 100
km/h (62 mph) for trailer operation.
It is also recommended that you comply with the local
regulations if the driving speed with a trailer is limited to
less than 100 km/h (62 mph).
● To prevent shocks from an overrun brake, depress the
brake pedal lightly at first and then more strongly.
● To make full use of engine braking, change to a lower
gear before descending a slope.
● The body, brakes, clutch, and chassis will be under addi-
tional strain when towing a trailer.
● The heavier weight and high er rolling and air resistance
will increase fuel consumption.
Page 233 of 450
For pleasant driving5-17
5
Air conditioning switchE00703500798
Push the switch, and the air conditioning compressor will start
working. The air conditioning indicator lamp (A) will come on.
Push the switch agai n and the air conditioning compressor will
stop working and the indicator lamp goes off.
Operating the air conditioning systemE00704100078
Heating
Set the mode selection dial to the “ ” position and set the air
selection switch (A) to the outside position.
Turn the temperature control dial clockwise or anticlockwise to
the desired temperature. Sel ect the desired blower speed.
NOTE●For maximum heat, set the bl ower speed at the 3rd posi-
tion.
CAUTION!
● When using the air conditi oning, the idling speed
may increase slightly as the air conditioning com-
pressor is switched on/off automatically. While the
vehicle with an automated manual transmission is
stationary, fully depress th e brake pedal to prevent
the vehicle from creeping.
Page 334 of 450
6-44 For emergencies
6
On a flooded road
●Avoid flooded roads. Water could enter the brake discs,
resulting in temporarily ineff ective brakes. In such cases,
lightly depress the brake pedal to see if the brakes are
operating properly. If they are not, lightly depress the
pedal several times while driving in order to dry the brake
pads.
● When driving in rain or on a road with many puddles, a
layer of water may form between the tyres and the road
surface.
This reduces a tyre’s frictional resistance on the road,
resulting in loss of steering stability and braking capabil-
ity.
To cope with this, observe the following:
On a snow-covered or frozen road
●When driving on a snow-covered or frozen road, it is rec-
ommended that you use snow tyres or tyre chains.
Refer to the “Snow tyres” and “Tyre chains” sections.
● Avoid high-speed operation, sudden acceleration, abrupt
brake application and sharp cornering.
● Depressing the brake pedal during travel on snowy or icy
roads may cause tyre slippage and skidding. When trac-
tion between the tyres and the road is reduced, the wheels
may skid and the vehicle cannot readily be brought to a
stop by conventional braking techniques. Braking will dif-
fer, depending upon whether you have anti-lock brakes
(ABS). As your vehicle is equipped with anti-lock brakes
(ABS), brake by pressing th e brake pedal hard, and keep-
ing it pressed.
● Allow extra distance between yo ur vehicle and the vehicle
in front of you, and avoid sudden braking.
On a bumpy or rutted road
Drive as slow as possible when driving on bumpy or rutted
roads.
(a) Drive your vehicle at a slow speed.
(b) Do not drive on worn tyres. Always maintain the specified tyre inflation pressures.
CAUTION!
●The impact on tyres and/ or wheels when driving on
a bumpy or rutted road can damage the tyre and/or
wheel.
Page 339 of 450
Vehicle care7-5
7
●If your vehicle has rain sensor wipers, place the
wiper switch lever in the “ ” (OFF) position to
deactivate the rain sensor before washing the vehi-
cle. Otherwise, the wipers will operate in the pres-
ence of water spray on the windscreen and may get
damaged as a result.
● Refrain from using a car wash as its brushes may
scratch the paint surface, ca using it to lose its gloss.
Scratches will be especially visible on darker col-
oured vehicles.
● Never spray or splash water on the electrical compo-
nents in the engine compartment, as this may
adversely affect engine starting.
Exercise caution also when washing the underbody;
be careful not to spray wa ter into the engine com-
partment.
● Some types of hot water washing equipment apply
high pressure and heat to the vehicle. They may
cause heat distortion and damage to the vehicle resin
parts and may result in floo ding of the vehicle inte-
rior. Therefore; ob serve the following.
• Maintain a good distance of approx. 50 cm or more
between the vehicle body and the washing nozzle.
• When washing around the door glass, hold the
nozzle at a distance of more than 50 cm and at
right angles to the glass surface.
CAUTION!
● After washing the vehicle, drive the vehicle slowly
while lightly depressing the brake pedal several
times in order to dry out the brakes.
Leaving the brakes wet could result in reduced
braking performance. There is also a possibility that
they could freeze up or b ecome inoperative due to
rust, rendering the vehicle unable to move.
● When using an automatic car wash, pay attention to
the following items, referi ng to the operation man-
ual or consulting a car wash operator. If the follow-
ing procedure is not followed, it could result in
damage to your vehicle.
• The outside mirrors are retracted.
• The antenna is removed.
• The rear wiper arm assembly is taped or removed.
• If your vehicle is equipped with a rear spoiler, con- sult a car wash operator be fore using the car wash.
• If your vehicle has rain sensor wipers, place the
wiper switch lever in th e “ ” (OFF) position to
deactivate the rain sensor.
CAUTION!