link MITSUBISHI COLT 2008 Owner's Manual (in English)

Locking and unlocking1-5
1
NOTE●If you lose your key, you can order a new one from your
MITSUBISHI MOTORS Authorized Service Point.
To obtain a replacement or additional spare key, take your
vehicle and all existing keys to your MITSUBISHI
MOTORS Authorized Service Point. All the keys have to
be re-registered in the immobilizer computer unit. The
immobilizer can register up to eight keys.Keyless entry system*
E00300301352
Press the remote control switch to lock or unlock all the doors
and the tailgate.
To l o c k
Press the LOCK switch (1) to lock all the doors and the tail-
gate. When they are locked th e turn-signal lamps blink once.
NOTE●With a vehicle that has a Dead Lock System, pressing the
LOCK switch (1) two times in succession causes the Dead
Lock System to be set. (Refer to “Setting the system” on
page 1-11.)
CAUTION!
●Don’t make any alterations or additions to the
immobilizer system; alterati ons or additions could
cause the immobilizer to fail.
1- LOCK switch
2- UNLOCK switch

1-6 Locking and unlocking
1
To unlock
Press the UNLOCK switch (2) to unlock all the doors and the
tailgate.
If they are unlocked while the room lamp is not illuminated,
the room lamp will be turned on for approximately 15 seconds
and the turn-signal lamps will blink twice.
NOTE● If the UNLOCK switch (2) is pressed and any of the doors
or tailgate is not opened within approximately 30 seconds:
relocking will automatically occur.
● It is possible to modify the functions as follows:
For further information, contact your MITSUBISHI
MOTORS Authorized Service Point.
• The time from pressing of the UNLOCK switch (2) to
the moment of automatic locking can be changed.
• The confirmation function (f lashing of the turn-signal
lamps) can be set to operate only when the doors and
tailgate are locked or only when the doors and tailgate
are unlocked.
• The confirmation function (which indicates locking or unlocking of the doors and ta ilgate with the flash of the
turn-signal lamps) can be deactivated.
• The number of times the turn-signal lamps are flashed by the confirmation function can be changed.
Operation of the Dead Lock System
For vehicles with a Dead Lock System, the Dead Lock System
can be set using the remote controller.
(Refer to “Dead Lock System’’ on page 1-10.)
NOTE● For vehicles with a Dead Lo ck System, the keyless entry
system will not work while the key is in the ignition
switch.
● Pressing the LOCK switch (1) has no effect (no locking
takes place) if a door or the tailgate is open.
● The remote control switch will operate within about 4m
from the vehicle. However, the operating range of the
remote control switch may chan ge if the vehicle is located
near a TV transmitting tower, power station, or radio
broadcasting station.
● If the turn-signal lamps flash 9 times when you press the
remote control switch, the battery may have run down.
Have the battery replaced by a MITSUBISHI MOTORS
Authorized Service Point.
● If your remote control switch is lost or damaged, please
contact your MITSUBISHI MOTORS Authorized Service
Point for a replacement remote control switch.
● If you wish to add a remote control switch, please contact
your MITSUBISHI MOTORS Authorized Service Point.
A maximum of eight remote control switches are availa-
ble for your vehicle.

2-52 Seat and seat belts
2
The air bags will operate only when the ignition switch is in the
“ON” or “START” position.When the impact sensors detect
an impact of sufficient frontal
or side force, an automated circuit ignites materials in the infla-
tor to generate gas and inflate the air bags.
The deployment of the air bags produces a sudden, loud noise,
and releases some smoke and powder, but these conditions are
not injurious and do not indicate a fire in the vehicle. People
with respiratory problems may feel some temporary irritation
from chemicals used to produce the deployment; open the win-
dows after air bag deployment, if safe to do so.
The air bags deflate very rapidl y after deployment, so there is
little danger of obscured vision.
The time required from the sensors detecting an impact to
deflation of the air bags after deployment is shorter than a blink
of an eye.
7- Side air bag modules*
8- Curtain air bag modules*
9- Side impact sensors*CAUTION!
● Air bags inflate at an ex tremely rapid speed. In cer-
tain situations, contact with inflating air bags can
result in light cuts, bruises, and the like.

3-8 Instruments and controls
3Indicator lamps
E00501600012
Turn-signal indicator lamps/Hazard
warning indicator lamps
E00501700042
These indicator lamps blink on and off when a
turn-signal lamp is operating.
NOTE●
If the blinking is too fast, the cause may be
a faulty turn-signal connection or a blown
lamp bulb.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash on and
off continuously.
High-beam indicator lampE00501800072
This indicator lamp illuminates when the high
beam is used.
Front fog lamp indicator lamp*E00501900158
This indicator lamp illuminates while the front
fog lamps are on.
Rear fog lamp indication lampE00502000084
This indication lamp illuminates while the rear
fog lamp is on.
Low coolant temperature indicator
lamp
E00502200028
When the engine coolant temperature is low, this
indicator lamp illuminates and then goes out
when the temperature rises to roughly 40 °C or
more.
NOTE● When the indicator lamp goes out, this
should be used as a rough indication of
when the heating starts working.
● If the indicator lamp stays illuminated,
there may be a fault in the temperature sen-
sor or other component. We recommend
you to have your vehicle inspected.

4-44 Starting and driving
4
Traction control system (TCL)/Active stability
control system (ASC) indicator lamp
E00612100092
The traction control system (TCL ) and active stability control
system (ASC) share the same indicator lamp.
The indicator lamp should illuminate when the ignition switch
is turned to the “ON” position, and should go off after a few
seconds. Always make sure that the lamp goes off before
begining to drive.
If the indicator lamp stays on or does not illuminate when the
ignition switch is turned to the “ON” position, we recommend
that you consult a MITSUBISHI MOTORS Authorized Serv-
ice Point.
indicator lamp blinks when the traction control system
(TCL) or active stability contro l system (ASC) is operating.
CAUTION!
●When the indicator lamp blinks, the traction con-
trol system (TCL) or acti ve stability control system
(ASC) is operating, which means that the road is
slippery or that your vehicle’s wheels are slipping
excessively. If this happens, drive more slowly with
less accelerator input.
● If a malfunction occurs in the device, the indica-
tor lamp will illuminate continuously. Park your
vehicle in a safe place and stop the engine. Then
start the engine again and check whether the
indicator lamp goes out.
If the indicator lamp re mains on even after your
vehicle is driven a short distance after starting the
engine, we recommend that you consult a
MITSUBISHI MOTORS Authorized Service Point.

5-34 For pleasant driving
5
1. NEWS
2. AFFAIRS (Current affairs)
3. INFO (Information)
4. SPORT
5. EDUCATE (Education)
6. DRAMA
7. CULTURE
8. SCIENCE
9. VARIED
10. POP M (Pop music) 11. ROCK M (Rock music)
12. EASY M (Easy music)
13. LIGHT M (Light classics)
14. CLASSICS
15. OTHER M (Other music)
16. WEATHER (Weather information)
17. FINANCE
18. CHILDREN
19. SOCIAL
20. RELIGION
21. PHONE IN
22. TRAVEL
23. LEISURE
24. JAZZ
25. COUNTRY
26. NATION M (National music)
27. OLDIES
28. FOLK M (Folk music)
29. DOCUMENT To search for a broadcast of desired program type:
1. Press the PTY button (7).
2. Press the TUNE/SEEK button (3 or 4) for less than 1 sec- ond at a time to select your desired PTY.
3. Two seconds after a desired PTY has been selected, the radio will begin to search for a broadcast of your selected
PTY. During search, the selected PTY on the display
blinks and the radio will begin to search for a broadcast of
your selected PTY.
4. When the radio picks up a station with your desired PTY, the display will show the name of the station.

For pleasant driving5-49
5
NOTE●With a disc that contains both CD-DA and MP3 files, the
random mode causes only files of the same format (CD-
DA only or MP3 files only) to be played in a random
sequence.
To find the start of each track on a disc for playback
Press the SCAN button (10). “SCAN” will appear on the dis-
play and the CD player will play back the first 10 seconds of
each track on the selected disc.
The track number will blink while the scan mode is selected.
To exit the scan mode, press the SCAN button again.
NOTE●Once all tracks on the disc have been scanned, playback
of the disc will restart from the beginning of the track that
was playing when scanning started.
● The scan mode will be canceled when radio or CD opera-
tion is selected.
● With a disc that contains both CD-DA and MP3 files, the
scan mode causes only files of the same format (CD-DA
only or MP3 files only) to be played.
To eject a disc
When the CD eject button (2) is pressed, the disc automatically
stops and is ejected. The syst em automatically switches to
radio mode.

8
Maintenance
Service precautions . . . . . . . . . . . . . . . . . . . . . . . .8- 2
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . .8- 3
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 4
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 7
Engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 11
Washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 14
Brake fluid/Clutch fluid* . . . . . . . . . . . . . . . . . . . .8- 14
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 15
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 19
Parking brake lever stroke . . . . . . . . . . . . . . . . . . .8- 24
Wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 25
General maintenance . . . . . . . . . . . . . . . . . . . . . . .8- 28
For cold and snow weather . . . . . . . . . . . . . . . . . .8- 29
Fuse links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 30
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 30
Replacement of lamp bulbs . . . . . . . . . . . . . . . . . .8- 40

8-30 Maintenance
8Fuse links
E01002900030
The fuse links will melt to prev
ent a fire if a large current
attempts to flow through certain electrical systems.
In case of a melted fuse link, we recommend you to have your
vehicle inspected.
Fuses
E01003001514
Fuse block location
To prevent damage to the el ectrical system due to short-
circuiting or overloading, each individual circuit is provided
with a fuse.
There is fuse block in the passenger compartment.
LHD

8-34 Maintenance
8
●Some fuses may not be installed on your vehicle, depend-
ing on the vehicle model or specifications.
● The table above shows the ma in equipment corresponding
to each fuse.
Identification of fuse
39 Ignition coil (Petrol-powered
vehicles)
10 A
O2 sensor (Diesel-powered vehi-
cles)
40 Gauge 7.5 A
41 Relay 7.5 A
42 Stop lamps 15 A
43 — ——
44 — ——
No. Symbol Electrical systemCapacity
7.5 A Brown
10 A Red
15 A Blue
20 A Yellow
30 A Green
40 A Orange (fuse type) / Green (fusible link type)