bulb MITSUBISHI ECLIPSE 2010 4.G User Guide

Vehicle care and maintenance
7-53
7
Adjustment of headlight aim
N00943200121
The alignment of the headlights should be checked by an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.Parking and side-marker lights (vehicles with
high intensity discharge headlights)
N00917300280
1. When replacing the bulb on the left side, remove the cap
(A) of the headlight by turning it counterclockwise.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the headlights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
* - Front of the vehicle
BK0098300US.book 53 ページ ２００８年１２月８日　月曜日　午前１１時３７分

7-54 Vehicle care and maintenance
7
2. Remove the socket and bulb assembly (B) together by
turning it counterclockwise.3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
BK0098300US.book 54 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-55
7
Front turn signal lights (vehicles with high inten-
sity discharge headlights)
N00943400022
1. When replacing the bulb on the left side, remove the cap
(A) of the headlight by turning it counterclockwise.2. Remove the socket and bulb assembly (B) together by
turning it counterclockwise.* - Front of the vehicle
BK0098300US.book 55 ページ ２００８年１２月８日　月曜日　午前１１時３７分

7-56 Vehicle care and maintenance
7
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
Front turn signal, parking and side-marker lights
(except for vehicles with high intensity discharge
headlights)
N00943400048
1. Remove the entire socket and bulb assembly (A) by turn-
ing it clockwise (the left side) or counterclockwise (the
right side).*- Front of the vehicle
BK0098300US.book 56 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-57
7
2. Depress the tab (B) on the harness connector and pull the
harness connector to remove it.
3. To install the bulb, perform the removal steps in reverse.
Front fog lights
(if so equipped)
N00943600532
1. Remove the three clips (A) by turning them counterclock-
wise or prying them, and remove the two screws (B) by
turning them counterclockwise, then remove the cover
(C).
BK0098300US.book 57 ページ ２００８年１２月８日　月曜日　午前１１時３７分

7-58 Vehicle care and maintenance
7
2. Remove the socket and bulb assembly (D) by turning
them counterclockwise.3. Disconnect the harness connector by pulling the tab (E) in
the direction of the arrow as shown. Then pull the harness
connector (F) to remove the bulb.
4. To install the bulb, perform the removal steps in reverse.
BK0098300US.book 58 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-59
7
Rear combination lights
N00943700328
ECLIPSE1. Open the rear hatch.
Push the center of the clips (A) and remove them. Then
remove the cover (B).
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the front fog lights
are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0098300US.book 59 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-61
7
4. Insert the tip of the screwdriver at the edge of the light
unit, pry gently to remove the light unit.
Then move the light unit toward the rear of the vehicle
and remove the clip (F).NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.5. Remove the socket and bulb assemblies by turning them
counterclockwise.
Remove the bulb by pulling it out.
G- Back-up light
H- Rear turn signal light
I- Rear side-marker light
BK0098300US.book 61 ページ ２００８年１２月８日　月曜日　午前１１時３７分

7-62 Vehicle care and maintenance
7
6. To install the bulb, perform the removal steps in reverse.NOTE
When mounting the light unit, align the clip (F), pins and
bolts (J) on the light unit with the holes in the body.
ECLIPSE SPYDER1. Open the trunk lid.
Push the center of the clips (A) and remove them. Then
remove the cover (B).
BK0098300US.book 62 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-65
7
5. Insert the tip of the screwdriver at the edge of the light
unit, pry gently to remove the light unit.
Then move the light unit toward the rear of the vehicle
and remove the clip (F).NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.6. Remove the socket and bulb assemblies by turning them
counterclockwise.
Remove the bulb by pulling it out.
G- Back-up light
H- Rear turn signal light
I- Rear side-marker light
BK0098300US.book 65 ページ ２００８年１２月８日　月曜日　午前１１時３７分