engine MITSUBISHI ECLIPSE 2010 4.G Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2010, Model line: ECLIPSE, Model: MITSUBISHI ECLIPSE 2010 4.GPages: 496, PDF Size: 15.63 MB
Page 117 of 496
3-22 Features and controls
3Theft-alarm system
N00510200068
The theft-alarm system is designed to provide protection from
unauthorized entry into the vehicle. This system is operated in
three stages: the first is the “armed” stage, the second is the
“alarm” stage, and third is the “disarmed” stage. If triggered,
the system provides both audible and visual alarm signals.
Armed stage
N00510300069
Park the vehicle and stop the engine. Arm the system as
described below.
1. Remove the key from the ignition switch.
2. Make sure that the engine hood is locked.
3. Lock all doors and the rear hatch or trunk lid by using
power door lock switch or the remote control transmitter.NOTEThe system is also armed by locking your vehicle using
the following procedures when you leave the vehicle.
• With either the driver’s door or passenger’s door open,
set the inside lock knobs on both doors to the locked
position and then close the door.
• With either the driver’s door or passenger’s door open,
lock all doors and the rear hatch or trunk lid using the
power door lock switch and then close the door.Arm the system and leave.
BK0098300US.book 22 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 118 of 496
Features and controls
3-23
3
After completion of the steps above, the theft-alarm indicator
(A) will illuminate for approximately 20 seconds and keeps
blinking on and off, indicating that the system is armed.
NOTEThe system will be armed even if the engine hood is open,
but when the system is set, be sure that the engine hood is
locked.
The system will be disarmed if, while the theft-alarm indi-
cator (located in the front center of the dashboard) is illu-
minated, all doors and the rear hatch or trunk lid are
unlocked by remote control transmitter.
The system will be disarmed if, while the theft-alarm indi-
cator is illuminated, the ignition key is turned to the “ON”
or “ACC”.
The system will not be armed if a door is not completely
closed. If this happens, rearm the system as described
above.
The trunk lid can only be opened by remote control trans-
mitter without triggering or disarming the system even
after the system has been armed. When it is closed, the
system will be rearmed.
The driver should not arm the system until first confirm-
ing that all passengers have left the vehicle. If the driver
arms the system with passenger(s) in the vehicle, the
alarm may be activated when the passenger(s) open the
door.
BK0098300US.book 23 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 119 of 496
3-24 Features and controls
3
Alarm stage
N00510400060
The alarm will be activated if any of the following occur while
the vehicle is parked and the system is armed.
1. One of the doors and the rear hatch or trunk lid is opened
without the remote control transmitter.
2. The engine hood is opened from the outside.Type of alarmWhen the alarm is activated:
1. The headlights blink on and off for 3 minutes.
After 3 minutes the headlights automatically shut off.2. The horn will sound intermittently for 3 minutes.
NOTEThe alarm will continue to operate for 3 minutes. At the
end of that period, the alarm will automatically shut off to
save battery power. The system will then be rearmed until
the proper disarming step is taken.Alarm deactivationThe alarm can be deactivated in the following ways.
By using the remote control transmitter to lock or unlock
the door, the rear hatch or trunk lid.
Turn the ignition key to the “ON” position.Horn sounds!
Headlights blink on and off!
BK0098300US.book 24 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 120 of 496
Features and controls
3-25
3
Disarmed stage
N00510500061
The system will be disarmed when either of the following steps
are taken:
1. All doors and the rear hatch or trunk lid are unlocked by
the remote control transmitter.
2. The ignition key is turned to the “ACC” or “ON” position.
3. If the UNLOCK button is pressed when all doors and the
rear hatch or trunk lid are closed and no door is opened
within approximately 30 seconds, re-arming will automat-
ically occur.NOTEOnce the system has been disarmed, it cannot be rearmed
except by repeating the arming procedure.
Testing the theft-alarm system
N00510600059
Use the following procedure to test the system:
1. Lower the driver’s window.
2. Arm the system as explained in “Armed stage”.
3. Make sure that the theft-alarm indicator comes on and
flash in approximately 20 seconds.
4. Wait a few seconds and then unlock the driver’s side door
by using the inside door lock knob and opening the door.
5. Check to be sure that the horn sounds intermittently and
the headlights blink on and off when the door is opened.
6. Disarm the system by unlocking all doors and the rear
hatch or trunk lid by the remote control transmitter or
using the key.NOTETo make sure the alarm sounds when the engine hood is
opened, open the engine hood by using the engine hood
release lever when the system is in the “armed” stage.
Disarm…by remote control transmitter
BK0098300US.book 25 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 121 of 496
3-26 Features and controls
3Power windows
N00510800338
In an ECLIPSE SPYDER, operating a power window switch
causes the door window and quarter window to move together.
However, within about 4 inches from the fully closed position,
only the door window moves without accompanying the quar-
ter window.
NOTEDepending on the position of the door window, the door
window may briefly stop then continue moving before
reaching the fully closed position.
Never try to operate the main switch and sub switch in dif-
ferent directions at the same time. This will freeze the
window in position.
Operating the power windows repeatedly with the engine
stopped will run down the battery. Use the window
switches only while the engine is running. NOTEIf a power window stops moving during operation due to a
drop in the battery voltage, it may not automatically return
to normal operability when the battery has been charged.
In this event, take the following corrective action:
With the door closed, pull up the power window switch to
fully close the window. After releasing the switch, pull it
up again for approximately 1 second. Normal opening and
closing of the window will then be possible.
1- Open (down)
2- Close (up)
WA R N I N G
!Before operating the power windows, make sure
that nothing can be trapped (head, hands, fingers,
etc.) in the window. Never leave the vehicle without removing the key. Never leave a child alone in the vehicle.
BK0098300US.book 26 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 125 of 496
3-30 Features and controls
3
NOTEWhen leaving the vehicle unattended, be sure to close the
sunroof and remove the ignition key.
Do not try to operate the sunroof if it is frozen closed
(after snowfall or during extreme cold).
Do not sit on or place heavy luggage on the sunroof or
roof opening edge.
Do not apply any force that may cause damage to the sun-
roof.
Release the switch when the sunroof has reached a com-
pletely open or completely closed position.
If the sunroof does not operate when the sunroof switch is
operated, release the switch and check whether something
is trapped by the sunroof. If nothing is trapped, have the
sunroof checked at an authorized Mitsubishi Motors
dealer.
Be careful when tilting up the sunroof if a ski carrier or a
roof carrier is installed. Depending on the model of ski
carrier or roof carrier, the sunroof may contact the carrier
when the sunroof is tilted up.
Be sure to close the sunroof completely when washing the
vehicle or when leaving the vehicle.Do not put any wax on the weatherstrip (black rubber)
around the sunroof opening. If it is waxed, the weather-
strip cannot maintain a weatherproof seal with the sun-
roof.
After washing the vehicle or after it has rained, wipe off
any water that is on the sunroof before operating it.
Operating the sunroof repeatedly with the engine turned
off will run down the battery. Operate the sunroof only
while the engine is running.
WA R N I N G
!Do not stick your head, hands or anything else in the
sunroof opening. Before operating the sunroof, make sure that noth-
ing can be trapped (head, hands, fingers, etc.).Never leave a child (or other person who is incapa-
ble of safely operating the sunroof switch) alone in
the vehicle.
BK0098300US.book 30 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 128 of 496
Features and controls
3-33
3
To p s w i t c h e s
N00505100030
The top can be opened and closed using the switches. The top
moves only while a switch is being pushed.NOTEIf the OPEN switch and CLOSE switch are both pushed at
the same time, the operation indicator lamp will flash
slowly (approximately one flashes per second) and a tone
will sound intermittently and rapidly (approximately three
per second) to indicate that the top is not going to work.
To operate the top, release the switches and push the rele-
vant switch again.If the switches are continuously pushed one after the
other, a protection circuit may operate, making the electric
convertible top temporarily inoperable. In this event, the
operation indicator lamp will flash slowly (approximately
one flash per second) and a tone will sound intermittently
(approximately three times per second). Wait about 7 min-
utes, then try operating the electric convertible top again.
To open the top
N00505200031
1. Without obstructing traffic, stop the vehicle on a level,
firm surface where the top can be safely operated.
2. Securely apply the parking brake. If the vehicle has an
automatic transaxle, place the selector lever in the “P”
(PARK) position. If the vehicle has a manual transaxle,
place the gearshift lever in the “N” (Neutral) position.NOTEThe top can be operated with the selector lever of an auto-
matic transaxle in a position other than “P” (PARK) and
with the gearshift lever of a manual transaxle in a position
other than “N” (Neutral). For safety, however, you should
place the selector lever or gearshift lever (as relevant) in
the indicated position and apply the parking brake.
3. Start the engine.NOTEOperating the top without the engine running can drain the
battery. To avoid a dead battery, operate the top with the
engine running.
4. Pull down both sun visors.
1- OPEN switch
2- CLOSE switch
3- Operation indicator lamp
12
3
BK0098300US.book 33 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 131 of 496
3-36 Features and controls
3
NOTEDuring operation of the top, if the switch is released
before the top has fully closed or retracted, the top will
stop moving and the operation indicator lamp will flash
slowly (approximately one flash per second).
If operation of the top is stopped for more than 4 minutes
before it has fully closed or retracted, the top (depending
on its location) will slowly move toward the closed or
retracted position. During this time, the operation indica-
tor lamp will flash rapidly (approximately two flashes per
second) and the top switch will be inoperable. When the
operation indicator lamp stops flashing (approximately 2
minutes later), the top switch will again become operable.
The operation indicator lamp is illuminated while the top
is moving.
When the OPEN switch is pushed, the door windows and
quarter windows automatically open fully before the top
starts moving.
If the CLOSE switch is pushed when the top is fully
closed, the operation indicator lamp flashes slowly
(approximately one flash per second) and a tone sounds
intermittently and rapidly (approximately three times per
second) to indicate that the top is not going to move.
To close the top
N00505300045
1. When you push the CLOSE switch, a tone will sound and
the top will start to operate. Keep pressing the CLOSE
switch until the top is fully closed. Refer to “Top
switches” on page 3-33.NOTEWhen the top reaches the fully closed position, a tone
sounds once and the operation indicator lamp goes off to
show that the operation is complete.
WA R N I N G
!To avoid injury, keep hands and head away from the
top while it is operating.To prevent uncontrolled movement of the top,
always keep the vehicle engine running when oper-
ating the top.
BK0098300US.book 36 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 132 of 496
Features and controls
3-37
3
NOTEDuring operation of the top, if the switch is released
before the top has fully closed or retracted, the top will
stop moving and the operation indicator lamp will flash
slowly (approximately one flash per second).
If operation of the top is stopped for more than 4 minutes
before it has fully closed or retracted, the top (depending
on its location) will slowly move toward the closed or
retracted position. During this time, the operation indica-
tor lamp will flash rapidly (approximately two flashes per
second) and the top switch will be inoperable. When the
operation indicator lamp stops flashing (approximately 2
minutes later), the top switch will again become operable.
The operation indicator lamp is illuminated while the top
is moving.
When the CLOSE switch is pushed, the door windows
and quarter windows automatically open fully before the
top starts moving.
If the OPEN switch is pushed when the top is fully open,
the operation indicator lamp flashes slowly (approxi-
mately one flash per second) and a tone sounds intermit-
tently and rapidly (approximately three times per second)
to indicate that the top is not going to move.
WA R N I N G
!To avoid injury, keep hands and head away from the
top while it is operating.To prevent uncontrolled movement of the top,
always keep the vehicle engine running when oper-
ating the top.
BK0098300US.book 37 ページ ２００８年１２月８日 月曜日 午前１１時３７分
Page 156 of 496
Features and controls
3-61
3 Ignition switch
N00512400354
LOCKThe engine is off and the steering wheel is locked. The key can
be inserted and removed only when the switch is in this posi-
tion. ACCAllows operation of electrical accessories with the engine off. ON The engine runs and all accessories can be used.
START Engages the starter. After the engine starts, release the key and
it will return automatically to the “ON” position.NOTESome models are equipped with ignition switch illumina-
tion.
• The ignition switch illumination comes on while the
driver’s door is opened and remains on for about 30 sec-
onds after the driver’s door is closed.
• When you remove the ignition key from the ignition
switch, it will be illuminated for about 30 seconds.
However, it will go off even while the illumination
comes on if the ignition switch is turned to “ON” posi-
tion.
Your vehicle is equipped with an electronic immobilizer.
To start the engine, the ID code which the transponder
inside the key sends must match the one registered to the
immobilizer computer.
(Refer to “Electronic immobilizer” on page 3-3.)
Manual transaxle Automatic transaxle
BK0098300US.book 61 ページ ２００８年１２月８日 月曜日 午前１１時３７分