change time MITSUBISHI ENDEAVOR 2010 1.G User Guide

Features and controls
3-99
3

When the ignition switch is turned on, the average speed
which was being displayed when the ignition switch was
previously turned off will be displayed once again. Average fuel economy
N00500900033
The average fuel economy (B) from the time when the display
was last reset to the present moment is shown together with a
graph. For instructions on resetting the display, refer to “To
reset the display” on page 3-105.NOTE
The range (A) for which historical data are shown in the
graph can be changed. Refer to “Graph indication” on
page 3-106.

The unit for the average fuel economy can be set to mpg
or L/100 km. Refer to “Display unit selection” on page
3-106 or “Units customization” on page 3-120.
When the system cannot provide a definite value for aver-
age fuel economy, it is displayed as “--.-”.

When the ignition switch is turned on, the average fuel
economy which was being displayed when the ignition
switch was previously turned off will be displayed once
again.

Average fuel economy varies according to the conditions
under which a vehicle is travelling (road conditions, the
manner in which the vehicle is being driven, etc.).
Actual fuel economy may differ from the displayed aver-
age fuel economy.
BK0102600US.book 99 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-101
3
Countdown timer
N00501200020
It is possible to set a duration (up to 24 hours) and then view
the remaining time as the timer counts down to zero.
1. Press the “SET” function button to view the timer setting
display.2. Press the “SELECT” function button to put the cursor on
the item (hours/minutes) you wish to set.
Then use the “ ” function button to set your desired
time. Pressing “ ” function button for more than 2 sec-
onds will fast forward to the desired change.
Press the “SET” function button to finish setting the timer
duration. The display will return to its previous display.
NOTE
The timer duration cannot be set in units of seconds.
BK0102600US.book 101 ページ ２００９年３月３０日　月曜日　午後２時２分

3-102 Features and controls
3
3. Press the “START” function button to start the timer. To
stop the timer before it has reached 0:00:00, press the
“STOP” function button.NOTE
If the timer reaches 0:00:00 while another display is
showing, a tone sounds once and the display changes to
the countdown timer for seven seconds.
If the “DISP” function button is pressed at this time, the
countdown timer disappears and the previous display
appears again.

When the countdown timer has started, the “START”
function button becomes the “STOP” function button.

Even if the ignition switch is turned to the “OFF” position
while the countdown timer is running, the countdown
timer continues counting down to 0:00:00.
Normally, a tone sounds to indicate that the countdown
timer has reached 0:00:00. It is possible to make a setting
so that the tone does not sound at this time. For details,
refer to “Timer buzzer setting” on page 3-126.
4. To reset the countdown timer, press the “SET” function
button for at least 2 seconds. The display will return to
0:00:00.
NOTE
Even if the “SET” function button is pressed while the
countdown timer is running, the countdown timer will not
be reset.

If the “SET” function button is pressed lightly one time,
the previously set timer duration will be shown. To
change the timer duration setting, perform the procedure
again from step 1.
BK0102600US.book 102 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-103
3
Elevation/Barometer
N00501300063
The elevation (A) of the vehicle’s present location and a
barometer (C) are shown together with a graph. For instruc-
tions on resetting the historical data in the graph, refer to “To
reset the display” on page 3-105.
NOTE
The range (B) for which historical data are shown in the
graph can be changed. Refer to “Graph indication” on
page 3-106.

The unit for elevation can be set to feet or meters. Refer to
“Display unit selection” on page 3-106 or “Units customi-
zation” on page 3-120.

The display can show elevations up to 12,000 feet (4,000
meters).

The altimeter displays the elevation to the nearest 200 feet
(50 meters). When the vehicle is below sea level, the ele-
vation is shown as 0 feet (0 meters).

The unit for the atmospheric pressure can be set to in.Hg,
hPa, kPa, or mb.
Refer to “Units customization” on page 3-120.

The display can show the atmospheric pressure in the
range from 18.1 in.Hg (614 hPa) to 31.2 in.Hg
(1,058 hPa).

The altimeter works by using changes in atmospheric
pressure. This means it may be affected by changes in the
weather and other conditions, and show a figure different
from the real elevation.

Fluctuations in air pressure may change the figure dis-
played even when the vehicle remains in the same place.
This is normal.
BK0102600US.book 103 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-105
3
To reset the display
N00501700025
The reset mode changes each time the “AUTO/MANUAL”
function button is pressed once (for less than 1 second).

Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” position, the display is automatically
reset.
Manual reset mode
If you reset the display at the time when you want to start
the measurements, average speed/average fuel econ-
omy/elevation/outside temperature from that point of time
can be displayed.
Push the “AUTO/MANUAL” function button for more
than 2 seconds.
NOTE
While the ignition switch is in the “ON” position, the
automatic reset mode is permanently selected. If you wish
to make continuous measurements, select the manual
mode.

When the indications in one display is reset, the data for
other displays are reset at the same time.
A- Automatic reset mode
M- Manual reset mode
BK0102600US.book 105 ページ ２００９年３月３０日　月曜日　午後２時２分

3-106 Features and controls
3
Graph indication
N00501800039
The average speed, average fuel economy, elevation, and out-
side temperature are each shown as a graph at the same time as
being shown numerically.
The range for which historical data are shown in the graphs
changes each time the “RANGE” function button is pressed
lightly.

-3 hours: The average value is added to the graph every 6
minutes. Data for a maximum of three hours are shown in
the graph.

-12 hours: The average value is added to the graph every
24 minutes. Data for a maximum of twelve hours are
shown in the graph.
NOTE
When the range for which historical data are shown is
changed for one graph, it also changes for the other
graphs.Display unit selection
N00501900027
When you want to select the other unit, pressing the function
button (A) for more than 3 seconds changes the unit as follows.
Mode
Unit
Driving range miles
→km
→milesAverage speed mph
→km/h
→mph
Average fuel economy mpg
→L/100km
→mpg
Elevation feet (ft)
→m
→feet (ft)
BK0102600US.book 106 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-109
3
Basic operation
N00535400087
NOTE
Every time the “DISP” button is pressed lightly, the moni-
tor will return to the previous display.

When the “BACK” function button is shown, pressing it
causes the monitor to return to the previous display.
1. Press the “DISP” button for at least 2 seconds to change
the display.2. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “1.Display brightness adjustment” → P. 3 - 1 1 2
• “2.Turn off Display” → P. 3 - 1 1 4
• “3.Record Maintenance” → P. 3 - 1 1 5
• “4.Next menu (Operable only with vehicle stationary)”
→ Proceed to step 3 of this procedure.
CAUTION
!
It is dangerous to operate the display while driving
the vehicle. Operate the display only when the vehi-
cle is safely parked.
BK0102600US.book 109 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-125
3
2. Press the “ ” function button, align the cursor with the
function you wish to change, and press the “SELECT”
function button.
• “Rheostat synchronization” → P. 3 - 1 2 5
• “Timer buzzer setting” → P. 3 - 1 2 6
•“History” → P.3-127
• “Opening display setting” → P.3-128
Rheostat synchronization
N00502300028
It is possible to disable the function that adjusts the monitor
brightness in synchronization with the instrument panel light
dimmer control.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• ON: Display brightness synchronized with instrument
panel light dimmer control
• OFF: Display brightness not synchronized with instru-
ment panel light dimmer controlNOTE
The initial (default) setting is “ON”.
BK0102600US.book 125 ページ ２００９年３月３０日　月曜日　午後２時２分

3-126 Features and controls
3
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Rheostat synchronization” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Rheostat
synchronization” display.Timer buzzer setting
N00502400029
It is possible to turn on or off the function that causes the tone
to sound when the countdown timer reaches 0:00:00.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• ON: The tone sounds.• OFF: The tone does not sound.
NOTE
The initial (default) setting is “ON”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Timer buzzer setting” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Timer
buzzer setting” display.
BK0102600US.book 126 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-131
3
2. To change the month, day and year readings, press the
“SELECT” function button. Each time the “SELECT”
function button is pressed, the item to be adjusted will
switch between month/day/year.
Press the “ ” function button to change to the desired
month or number. Pressing “ ” function button for more
than 2 seconds will fast forward to the desired change.
When the date has been adjusted, press the “SET” func-
tion button. The display will return to its previous display.NOTE
When the “ ” function button is pressed, the month, day,
and year indications change as follows:
• month: JAN → FEB → ••• → DEC → JAN → •••
•day: 1 → 2 → 3 → ••• → 31 → 1 → •••
• year: 2006 → 2007 → 2008 → ••• → 2098 → 2006 •••
Compass zone code setting
N00534300047
1. Find your current geographic location and the correct cor-
responding zone number on the zone map.
BK0102600US.book 131 ページ ２００９年３月３０日　月曜日　午後２時２分