keyless MITSUBISHI ENDEAVOR 2010 1.G User Guide

3-112 Features and controls
3
7. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “Lights”
→ Refer to “Lights customization” on page 3-135
•“Wipers”
→ Refer to “Wipers customization” on page 3-139
• “Keyless entry system & power door lock system”
→ Refer to “Keyless entry system & power door lock
system customization” on page 3-142
• “Buzzers”
→ Refer to “Buzzers customization” on page 3-147
Display brightness adjustment
N00533800074
It is possible to adjust the display brightness that is seen when
the light switch is “OFF”.
When the light switch is in the “ ” or “ ” position, it is
possible to make fine adjustments after making adjustments
using the instrument panel light dimmer control.NOTE
When the light switch is in the “ ” or “ ” position,
pressing the “BRIGHT” function button causes the bright-
ness to change to that seen when the light switch is
“OFF”.
To return the brightness to the original level, press the
“BRIGHT” function button again.
BK0102600US.book 112 ページ ２００９年３月３０日　月曜日　午後２時２分

3-142 Features and controls
3
Keyless entry system & power door lock system customi-
zation
N00534700038
1. Display “Keyless entry system & power door lock sys-
tem” on the monitor in accordance with “Basic operation”
(see page 3-109), align the cursor with it, and press the
“SELECT” function button.2. Press the “ ” function button, align the cursor with the
function you wish to change, and press the “SELECT”
function button.
BK0102600US.book 142 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-143
3
• “Keyless entry system confirmation by horn” → P. 3 - 1 4 3
• “Keyless entry system confirmation by turn signal
lights” → P. 3 - 1 4 3
• “Keyless entry automatic relocking time” → P. 3 - 1 4 5
• “Unlock operation using keyless entry system or door
key” → P. 3 - 1 4 6
Keyless entry system confirmation by horn
N00536000093
It is possible to change the confirmation function provided by
the horn when the keyless entry system is used to lock the
doors.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A: The horn sounds when the doors and the liftgate are
locked.
• B: When a lock operation has been performed, the horn
sounds when the “LOCK” button is pressed again.• C: The horn does not sound.
NOTE
The initial (default) setting is “B”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry system confirmation by horn” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry system confirmation by horn” display.Keyless entry system confirmation by turn signal lights
N00536100065
It is possible to change the confirmation function provided by
the turn signal lights when the keyless entry system is used to
lock or unlock the doors and the liftgate.
BK0102600US.book 143 ページ ２００９年３月３０日　月曜日　午後２時２分

3-144 Features and controls
3
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A:The turn signal lights blink when the doors and the
liftgate are locked or unlocked.
• B:The turn signal lights blink only when the doors and
the liftgate are locked.
• C:The turn signal lights blink only when the doors and
the liftgate are unlocked.
• D:The turn signal lights do not blink.NOTE
The initial (default) setting is “A”.2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry system confirmation by turn signal lights”
display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry system confirmation by turn signal lights” display.
BK0102600US.book 144 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-145
3
Keyless entry automatic relocking time
N00536200066
It is possible to change the time that elapses before automatic
relocking when the keyless entry system has been used to
unlock and no doors and the liftgate are opened.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A:30 seconds
• B:60 seconds
• C:120 seconds
• D:180 secondsNOTE
The initial (default) setting is “A”.2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry automatic relocking time” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry automatic relocking time” display.
BK0102600US.book 145 ページ ２００９年３月３０日　月曜日　午後２時２分

3-146 Features and controls
3
Unlock operation using keyless entry system or door key
N00536300067
It is possible to change the door(s) and the liftgate that will be
unlocked when an unlock operation is performed using the
keyless entry system or when the driver’s door is unlocked
using the key.1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.BK0102600US.book 146 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-147
3
• A:A single unlock operation unlocks only the driver’s
door.
Two unlock operations unlock all of the doors and the
liftgate.
• B:A single unlock operation unlocks all of the doors and
the liftgate.
NOTE
The initial (default) setting is “A”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Unlock operation using keyless entry system or door
key” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Unlock
operation using keyless entry system or door key” display.
Buzzers customization
N00534900056
1. Display “Buzzers” on the monitor in accordance with
“Basic operation” (see page 3-109), align the cursor with
it, and press the “SELECT” function button.
BK0102600US.book 147 ページ ２００９年３月３０日　月曜日　午後２時２分

3-150 Features and controls
3
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
the tone will sound once and the monitor will return to the
“Door-ajar warning buzzer” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Door-ajar
warning buzzer” display.
Number of keyless entry registration
N00535200030
It is possible to confirm the number of registered remote con-
trol transmitters.
1. Display “Number of keyless entry registration” on the
monitor in accordance with “Basic operation” (see page
3-109), align the cursor with it, and press the
“SELECT” function button.
BK0102600US.book 150 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-199
3
NOTE
With the switches on the rear personal lights
and luggage room light in the “OFF” position,
the rear personal lights and luggage room light
stay off when the interior light switch is in the
“DOOR” position and a door or the liftgate is
opened.
When all the doors and the liftgate are closed, the
interior lights are dimmed gradually for 30 seconds
then go off. However, the lights go off immediately
without being dimmed if:

The ignition switch is turned to the “ON”
position.

All the doors and the liftgate are locked using
the lock knobs of the front doors, the power
door lock switch, or the remote control switch
from the keyless entry system.NOTE
If the ignition key is removed with the doors
and the liftgate closed, the interior lights come
on for 30 seconds period then go off.

When the switches of the reading lights, rear
personal lights and luggage room light are in
the “ON” position, these lights do not go off
when all the doors and the liftgate are closed.

In a vehicles with multi center display, the
multi center display can be used to change the
dimming period of interior lights.
For details, refer to “Setting and customiza-
tion” on page 3-108.3 (OFF) - It is possible to turn off all of the interior lights
{dome light, reading lights, rear personal lights,
luggage room light and door lights} by placing the
interior light switch in the “OFF” position.
NOTE
When the switches of the reading lights, rear
personal lights and luggage room light are in
the “ON” position, these lights do not go off
when the interior light switch is placed to the
“OFF” position.
BK0102600US.book 199 ページ ２００９年３月３０日　月曜日　午後２時２分

Features and controls
3-203
3
Interior light auto-cutout function (dome light
and other lights)
N00526300367
If any of the interior lights are left on with the ignition switch
in the “LOCK” position, the lights go off automatically after
about 30 minutes.
The lights come on again if the ignition switch is turned to the
“ON” or “ACC” position, any door or the liftgate is opened and
closed, or the keyless entry system is operated.NOTE
In a vehicle with a multi center display, the multi center
display can be used to alter functions as listed below.
For details, please refer to “Setting and customization” on
page 3-108.
• The interior light auto-cutout function can be turned off.
• The interior light auto-cutout delay can be changed.
Accessory boxes
N00526400397
Convenient storage space is located throughout the vehicle.1- Cup holder
2- Bottle holder
3- Sunglasses holder (if so equipped)
4- Floor console box/Tissue holder
5- Glove compartment
BK0102600US.book 203 ページ ２００９年３月３０日　月曜日　午後２時２分