timing belt MITSUBISHI ENDEAVOR 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2010, Model line: ENDEAVOR, Model: MITSUBISHI ENDEAVOR 2010 1.GPages: 514, PDF Size: 112.17 MB
Page 461 of 514
7-34 Vehicle care and maintenance
7
the pulleys as shown in the illustration with a force of about 22
pounds (100N).
Check the drive belt for cuts and cracks, and replace it if it is
damaged.
When replacing the belt with a new belt, make sure that there is
no interference between the belt and other engine components.
Then, check the tension of the belt at the designated point. The
deflection must be within the specifications.Amount of belt deflectionExhaust system
N00942200010
The best way to keep carbon monoxide gas from entering
inside your vehicle is to have the engine exhaust system prop-
erly serviced.
Have a competent mechanic inspect the complete exhaust sys-
tem and nearby body areas for broken, damaged, deteriorated,
or mispositioned parts if you notice any of the following:
A change in the sound of the exhaust system
The smell of exhaust fumes inside the vehicle
The underside or rear of the vehicle is damaged
Also check the exhaust system each time the vehicle is raised
for lubrication, oil changes, or required service. Any open
seams or loose connections could let dangerous exhaust fumes
seep into the luggage compartment and passenger compart-
ments. Check for any of the following conditions: Check for holes or exhaust gas leaks caused by corrosion
or damage.
Check the joints and connections for looseness or exhaust
gas leaks.
Check the rubber hangers and brackets for damage.Timing belt
N00942300037
The timing belt should be replaced with a new one at the mile-
age listed in the “WARRANTY AND MAINTENANCE
MANUAL”.Hood lock release mechanism and safety catch
N00942500042
The hood lock release mechanism and hood safety catch should
be checked, cleaned, and oiled when needed for easy move-
ment and to stop rust and wear. Use Multipurpose Grease
NLGI Grade 2 sparingly for all sliding parts of the hood latch
Standard value
Used belt
New belt
A.48 to .64 inch
(12.3 to 16.2 mm).52 to .59 inch
(13.2 to 15.1 mm).38 to .48 inch
(9.6 to 12.3 mm)B.33 to .42 inch
(8.4 to 10.7 mm).35 to .40 inch
(8.9 to 10.1 mm).24 to .30 inch
(6.2 to 7.5 mm)
WA R N I N G
!Do not check or touch the drive belt with the engine
running, or serious injury or death may result.
WA R N I N G
!Carbon monoxide gas from your vehicle’s exhaust is
poisonous. Breathing these fumes can cause uncon-
sciousness or death.
BK0102600US.book 34 ページ 2009年3月30日 月曜日 午後2時2分
Page 512 of 514
Alphabetical index
7
Timer function 3-24
,3-26
Timing belt 7-34
Tire pressure monitoring system 3-69
Tires 7-20
Compact spare tire 6-14
How to change a tire 6-12
Inflation pressure 7-24
Maintenance 7-26
Quality grading 8-2
Replacing tires and wheels 7-26
Rotation 7-27
Size (tire and wheel) 9-7
Snow tires 7-28
Spare tire information 6-13
Tire and loading information placard 4-9
,9-3
Tire chains 7-29
Tread wear indicators 7-26
Tissue holder 3-204
Tonneau cover 3-208
Tools 6-8
Storage 6-7
Towing 6-23
Trailer towing 4-15
Transfer oil 7-13
,9-8
Trip odometer 3-78
Turn signal light
Bulb capacity 7-45
Indicators 3-83
Lever 3-157Replacement 7-48
,7-51
V
Vanity mirror 3-195
Vehicle care precautions 7-57
Vehicle dimensions 9-4
Vehicle labeling 9-2
Vehicle preparation before driving 4-3
Vehicle weights 9-5
Vents 5-2
W
Warning lights 3-83
Washer
Fluid 7-14
,9-8
Rear window washer 3-161
Switch 3-161
Windshield washer 3-161
Waxing 7-61
Weights 9-5
Wheel
Specification 9-7
Wiper
Rear window wiper 3-161
Switch 3-159
Windshield 3-159
Wiper blades 7-31
BK0102600US.book 7 ページ 2009年3月30日 月曜日 午後2時2分