fuse MITSUBISHI GALANT 1989 Service User Guide

AUTOMATIC TRANSAXLE - Troubleshootina
-
E
1OP
3
@IOA
PT.-. L-_..il Tr-ltn
-

.-
-~-------y~-J4 ~
!kJ-LBII
I II rrl
6Y
* YB
I
7"DI.
(RG)
@ (GL)I
g (GR)Is
2
t I
e_-_-_----_~~__---~~~~~~~ -------w-v----
BY
1 2
s
1
DEDICATED
FUSE
6 C-37
7J/B
8 C-32
POWER/
ECONOMY
!RRi OVER
1
J/C(TAIL)
ELC-4SPEED
AUTOMATIC
;;;f?;;lfLE
MODULE
(GR) 58;&
(RW) 574~
C-60
Remark Xmark
indicates the Optional wirin
g
harness for auto cruise control
system
1 TSB RevisionI

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting 33B-11
CHECKING BY USING THE SCAN TOOL
1. DIAGNOSTIC TROUBLE CODE OUTPUT
TROUBLESHOOTING CHART
DiagnostictroubleMalfunctionVehicle conditioncode No.Probable causeAction
0Normal---
Damaged or disconnected
Alarm light illuminates;0 Improper installation Troubleshoof
wiring or short-circuit of Gamong attitude-control of G sensor.
sensor input circuit, or Ging hints
modes, only rolling control
sensor malfunction. l
G sensor internal wiring
classified by
stops. damaged or disconnected. circuit
[I]
“11(Others operate normally.)l Damaged or disconnected
wiring or short-circuit of
G
sensor circurt.
l Connector of
G sensor
circuit disconnected.
0 Malfunction of ECU.
W
ith the ignition key at the
The charging warning light
ON position and the vehicle illuminates, and,
0 Insufficient generator “L”Troubleshoot
speed at 40 km/h (25 mph) furthermore, the system terminal output voltage
ing hints
or higher, the output does not function when the (malfunction of the
classified by
charging system). circuit
[2]
voltage of the generator ‘I”vehicle is stopped (vehicle0 Harness short-circuit
terminal is approximately speed of 3 km/h (2 mph) or
5V or lower
lower). between the generator“L” terminal and the ECU.“12
NOTEl ECU malfunction.
The alarm light does not illuminate, and,
furthermore, there is no
detection of harness
damage or disconnection
between the generator “L”
terminal and the ECU.
The low-pressure switch is The alarm light illuminates,
l Low-pressure switch is Troubleshoot
not switched OFF even and only the attitude-control
fused.
though the attitude-control ing hints
function stops. (Other l Damaged or disconnected classified by
function is performed 30 functions are normal.) circuit
131
13times. The return pump is wiring, or short-circuit, of
the low-pressure switch
activated frequently. circuit harness.
0 The connector of the
low-pressure switch
circuit is disconnected.
l Air leakage from the low-pressure tank
(including tubing).
l ECU malfunction.
“21
Damaged or disconnected The alarm light illuminates,l Steering angular-velocity Troubleshoot-
wiring of the steering and the attitude-control sensor malfunction.
angular-velocity sensor ing hints
function stops. The
input circuit, or a l Damaged or disconnected classified by
damping force is held to wiring of the steeringcircuit
191malfunction of the steenng
MEDIUM, and the vehicle
angular-velocity sensor. angular-velocity sensor
height is held to NORMAL circuit harness.
l Disconnection of the connector of the steering
angular-velocity sensor
circuit.
l ECU malfunction.
TSB Revision

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting 33B-13
Diagnostic
trouble
zode No.MalfunctionVehicle condition Probable causeAction
Damaged or disconnected The alarm light illuminates,
l All connectors of theTroubleshoot
wiring of the damping force and the attitude-control
damping-force switchinging hints
switching actuator (step function and the damping-
actuator (step motor classified by
motor type) or of the force control function are
type) and the actuatorcircuit
[ 171
actuator circuit, or a
stopped.
circuit are disconnected.
malfunction of an output The vehicle height is held to
l Damaged or disconnected41transistor within the ECU. NORMAL.
wiring, or a short-circuit, of
the damping-force
switching actuator (step
motor type) and the
harness of the ECU part of
the actuator circutt.
l ECU malfunction.
There is damaged or The alarm light illuminates,
l The solenoid valve power Troubleshoot-
disconnected wiring, or a and the attitude-control
short-circuit, of the solenoid source relay contacts are
ing hints
function and the
vehicle-fused. classified by
valve power source relay height control function are
circuit. l Damaged or disconnected circuit
(71stopped.
wiring of the solenoid
The damping force is held valve power source relay
to MEDIUM. coil.
42
l Damaged or disconnected
wiring, or a short-circuit, of
the solenoid valve power source relay circuit.
l Disconnection of the connector of the solenoid
valve power source relay
circuit.
l ECU malfunction.
Damaged or disconnected The alarm light illuminates,
l Damaged or disconnected Troubleshoot-
wiring, or a short-circuit, of and the attitude-control wiring, or a
short-circuit, ofing hints
the compressor relay function and the
vehicle-the compressor relay coil.classified by
circuit, or a malfunction of height control function are
l Damaged or disconnectedcircuit [I81an output transistor within
stopped.
43
the ECU.wiring, or a short-circuit, of
The damping force is held the compressor relay
to MEDIUM.
circuit harness.
l Disconnection of the
compressor relay circuit
connector.
l ECU malfunction.
Damaged or disconnected The alarm light illuminates,
l Damaged or disconnected Troubleshoot-
wiring, or a short-circuit, of and the attitude-control
wiring, or a short-circuit, ofing hints
the return pump relay function and the
vehicle-the return pump relay coil.classified by
circuit, or a malfunction of height control function are
l Damaged or disconnectedcircuit [I91an output transistor withinstopped.
the ECU.The damping force is heldwrring, or a short-circuit, of44
the return pump relay
to MEDIUM. circuit harness.
l Disconnection of the return pump relay circuit
connector.
l ECU malfunction.
TSB Revision

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshootina 33B-15
Diagnostic
trouble
code NoMalfunction Vehicle condition Probable causeAction
52
Damaged or disconnected
The alarm light illuminates, l Damaged or disconnected Troubleshoo
wiring of the left front or and the attitude-control wiring of the left front or
ing hints
right front valve actuation function and the vehicle- right front valve coil.
classified by
circuit, or a malfunction of height control function arel Damaged or disconnected circuit
[25]an output transistor within
stopped. wiring of the left front orthe ECU.The damping force is held
right front valve circuit
to MEDIUM. harness.
l Disconnection of the connector of the left front
or right front valve circuit.
l ECU malfunction.
53
Damaged or disconnected The alarm light illuminates,
wiring of the left rear or right l Damaged or disconnected Troubleshoot
and the attitude-control wiring of the left rear or
rear valve actuation circuit, ing hints
function and, the vehicle- right rear valve coil.
classified by
or a malfunction of an output height control function are
transistor within the ECU. l Damaged or disconnected circuit
[26]
stopped.
wiring of the left rear or
The damping force is held right rear valve circuit
to MEDIUM.
harness.
l Disconnection of the connector of the left rear
or right rear valve circuit.
l ECU malfunction.
54
55
Even though three mrnutes
The alarm light illuminates,0 Overloaded condition. Refer to
or more have passed for the and the attitude-control l Improper adjustment ofMalfunction
vehicle-height adjustments function and the vehicle- the front or rear
of the front and the rear, and Symptoms
height control function are vehicle-height sensor.
Chart [A] onthe pressure within thestopped.l Air-pressure line isP.33B-17.high-pressure
tank is
The damping force is held
sufficient (the high-pressure clogged.
to MEDIUM. l Malfunction of the front
switch is OFF), the strut unit or the rear shock
vehicle-height adjustments absorber unit air spring.
are not completed. l ECU malfunction.
Even though three minutes The alarm light illuminates,
l Compressor malfunction.Refer to
or more have passed for the and the attitude-control Damaged orMalfunction
vehicle-height adjustments function and the vehicle- disconnected wiring ofSymptoms
of the front and the rear, and height control function are
the harness between theChart
LB1 on
with insufficient pressure stopped. compressor relay and the
P.33B-17.
withtn the high-pressure tankThe damping force is held
compressor.
(the high-pressure
switch isto MEDIUM.
Malfunction of the air
iON), the vehicle-height compression of the
adjustments are not compressor.
completed, or the l Air leakage from the
compressor has operated
continuously for four high-pressure tank
minutes or longer. (non-airtight connection
with the low-pressure
tank).
l High-pressure switch is fused.
The return pump is Control functions are not Air leakage within the frontReplace the
continuously activated stopped (alarm lamp does (left or right) or rear (left orfront or rear
(repeatedly starts and stops not illuminate).
right) valve.solenoid
56erght times), even though
valve.
neither the attitude-control
function nor the
vehicle-height control
function has been initiated.
TSB Revision

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting 33B-35
Service data indication
Code No Indication
Standard value
17ECU input voltage indications when When switches are openSPORT, AUTO, SOFT, HIGH5V
switches are pressed.When SPORT switch
is ONOV
When AUTO switch is ON1.53v
When SOFT switch is ON 2.71V
When HIGH swrtch
is ON 4.02V
ACTIVE-ECS indicators check chart
1.Checking the power source circuit
Disconnect the battery terminals, and, after erasure of the
ECU mode memory, turn the ignition key to the ON position.
1
Indication example
17: MANUAL CNG. SW
4.03v
The sound of the damplng force switching actuators (steplNoThe ACTIVE-ECS power relay doesn’t function
motors), installed at the front struts and at the rear shock
--+l Disconnected or damaged wiring of the fusible link, the
absorbers, will be heard. fuse and/or the harness between the battery and the AC-TIVE-ECS power relay contacts
Yes
When terminal 15 of the ACTIVE-ECS indicator is grounded,yes
the “SOFT” damping force characteristic indicator and the -lDisconnected or damaged wiring of the ground line 15 of
“NORM” vehicle-height indicator will
illuminate.the ACTIVE-ECS indicator.
No
Approximately
12V is measured when the voltage betweenNo
ground and terminal 20 of the indicator and the ACTIVE-ECS --+l Disconnected or damaged wiring between the AC-
is measured. TIVE-ECS power relay and ECS Indicator
terminal 20.
I Yes
TSB Revision
-. ACTIVE-ECS Indicator power source circuit OK Proceed to
checking of the individual ACTIVE-ECS
lndlcators

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting 33B-57
Operation
The compressor is activated when the pressure
within the high-pressure tank decreases to 760
kPa
(108 psi) or lower, and then stops two seconds after
the pressure reaches 950
kPa (135 psi). Note,
however, that the compressor is not activated while
Diagnostic If there is damage or disconnection of the heavy-line
circuit, or a short-circuit, or a malfunction of the
output transistor within the ECU, the alarm light illuminates and control is as described in the table the return pump is operating. A thermal switch is
provided at the motor circuit. This thermal switch
functions to interrupt the power to the motor (in
order to protect the compressor) if the temperature
within the compressor becomes high.
below.
(Note that the diagnostic is only applicable up to the
compressor relay.)
Diagnostic No.
43
Attitude control
Control stop Damping force
control
Held at MEDIUM Vehicle-height
control
Control stopHIGH
Switch acceptance
SPORT AUTOSOFT
Not accept
Actuator compulsory activation
1 CodeNo. /Applicable operationIDescription of activationI
05Compressor relay ON The compressor relay is compulsorily switched ON for a period of three s\
econds.
ECU terminal voltages (when connector is connected)
TerminalNo.Signal ConditionTerminal
voltage
23Compressor relay actrvatron
signal When the compressor relay is ONB+
When the compressor relay is OFF o
v
During fail-safe ov
(solenoid valve power-source relay switch OFF) ---
TSB Revision
Checking the compressor drive circuit (with the connector disconnected)\
B+: Battery positive voltage
Terminal Connection destination or
MeasurementNo.measured part Tester connection
Check conditionStandard
~~
Compressor relay Resistance52-ground
Troubleshooting hints (mechanical malfunctions)
Malfunction
mode Malfunction probable cause
Malfunction
Note
The compressor relay is fused. The compressor relay contacts are shorted.
The compressor won’t stop, causing the battery
-to discharge.
The compressor is The compressor won’t operate due to shorting, The vehicle height can’t be increased.
-
stuck.
etc.

ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting 33B-59
Diagnostic
If there is damage or disconnection of the heavy-line illuminates and ‘control is as described in the table
circuit, or a short-circuit, or a malfunction of the
out-
put transistor within the ECU, the alarm ligh
t
below. (Note that the diagnostic is only applicable
up to the compressor relay.)
II/6
Diagnostic No.Attitude controlDamping forcecontrol Vehicle-height
control Switch acceptanceHIGH1 SPORT jAUTO) SOF
T
I44
Rolling control only
Held at
stops. MEDIUMRolling control only stoos.
Not accept
Actuator compulsory activation
CodeNo ’Applicable operation Descnption
of activation
06Return pump relay ON
The return pump relay is compulsorily switched ON for a period of three \
seconds.
ECU terminal voltages (when connector is connected) Terminalvoltage
I
3
2
Return pump relay activation signal
When the return pump relay is ON
B+
When the return pump relay is OFF o
v
During fail-safe ov
(solenoid valve power source relay switch OFF)
Checking the return pump drive circuit (with the connector disconnected\
)
B+: Battery positive voltage Connectron

destrnation or Measurementmeasured part Tester connectron
Check condrtronStandard
32Return pump relay
Resistance32-groundConstatly Approx 750INext apply battery voltage to
terminal 32. Return pump
operation
NOTE (Refer to Vol.2 GENERAL for the circuit diagram.)
Procedures for changing the internal pressure of the low-pressure tank
(1) For 70 kPa (IO psi) or lower
Short-circuit the battery power-source @ terminal to the return pump relay @ terminal in order to activate the return
pump for a few seconds, and then leave as is.
(2) For 140 kPa (20 psi) or higher
Short-circuit the battery power-source @ terminal to the front intake-air solenoid @I terminal and the front right
solenoid @I terminal in order to connect the high-pressure tank and low-pressure ta\
nk, and then leave as is for a few
seconds.
Procedures for changing the internal pressure of the high-pressure tank
(I) For 760 kPa (108 psi) or lower
Short-circuit the battery power-source @I terminal to the discharge-air solenoid (for vehicle-height adjustment)\
@Iterminal, the front intake-air solenoid @I terminal and the front right solenoid @ terminal and the front discharge-air
solenoid @I terminal in order to release the atmosphere inside the high-pressure ta\
nk, and then leave as is for a few
seconds.
(2) For 950 kPa (135 psi) or higher
Short-circuit the battery power-source @ terminal to the compressor relay @ terminal in order to activate the
compressor for a few seconds, and then leave as is.
Troubleshooting hints (mechanical malfunctions)
Malfunctionmode Malfunction probable cause
Malfunction
Note
1
The return pumpThe return pump relay contacts are shorted.
relay is fused The return pump won’t stop, causing the
battery to discharge.
The return pump is The return pump won’t operate due to short-
* Insufficient attitude-control effect.
-
stuck.ing.
etc. l
Vehicle height increases after rolling control.
TSB Revision

336-78 ACTIVE-ELECTRONIC CONTROL SUSPENSION - Troubleshooting
Concentrated junction
Dedicated fuses
@I-@ A-01X Headlight relayA-06X ACTIVE-ECS solenoidvalve power source relay
‘\
I,BR/LB
A-01X
\
8383mB
Sub fusible link 0-a
/
16A0567
ENGINE AND TRANSAXLE
B-l 5 Alternator
B-21 Backup light switchB-02-1 Throttle posltion
sensor (From 1990 models)
Ground point (detailed view)
36A0308
TSB Revision

35-16SERVICE BRAKES - Anti-lock Braking System Troubleshooting
TROUBLESHOOTING (ABS-FWD)
Confirm condition in the following way and diagnose accordingly.
Ioes the ABS warning light illuminate as describedpower to the ABS ECU is interrupted and the
lelow up to the time the engine starts?ABS warning light remains lit because the valve
1) When the ignition key is turned to the “ON” relay is OFF.
position, the ABS warning light blinks twice for (3) When the ignition key is turned from the “START’
approximately 1 second due to the ABS ECU (as position to the “ON” position, the ABS warning
a self check of the valve relays is performed), light blinks twice for approximately 1 second
and goes out and stays out. (during this time a recheck of the valve relays is
2) With the ignition key in the “START” position, performed), and then goes out and stays out.
ABS warning
,,lseq (se+
lightII
OFF -I
Ignitionkey
ABS warnmg/;,ght68A009314A0589
YAS rICONTINUE TO NEXT PAGENo
No.
Trouble condition
ABS warning light does not light up at all.
ABSwarnina
ON
OFF
1light -
lgnltionkey
I14 A0590
When the ignition key is turned to the l Fail safe is functioning due to ECU on-
“ON” position, it remains lighted. board diagnostic
ABSwarning
2lightOZ7
l Short in ECU warning light drive circuit
l Malfunction of ECU
lgnitlonkev
ACC. LOi+14A0591
Does not illuminate when ignition key is
in “START” position.
ABSwarning
3light
Ignition
key ACC. LO:+14AO592
Major causes
l ABS warning light bulb is burnt out.
l Open in ABS warning light electrical circuit (check for blown fuse)
l Malfunction of valve relay
l Break in harness between ABS warn- ing light and HU
l Break in harness between HU and body ground Remedy
Check, using flow
chart A (Refer to
P.35-21.)
Check, using flowchart B (Refer toP.35-24.)
Check, using flow:hart C (Refer to ‘.35-26.)
1 TSB Revision

SERVICE BRAKES - Anti-lock Braking System Troubleshooting35-21
A ABS warning light does not light at all.
[Explanation]
When it does not light up at all, there is a strong
possibility that there is trouble with ABS warning
light or with power to the light.
[Hint]
If other warning lights do not light up either, fuse is
probably blown.
MAIN FUSIBLE
LINK @IGNITIONSWITCH (IG2)IGNITIONSWITCH (IGl)
Ea
1
0 U
, ,8--1I
CL
, VALVE
fI*I1 RELAY 1 Ii 1,
M
i 10
z 13-
--3z2-&
rc11_ 3
t”71
_----
a-II
2
dt II
zz
c:
35 126J.27ABS ECU
1
GND GND GNDv v v
TSB RevisionI
14A0085