ignition MITSUBISHI GALANT 2011 9.G User Guide

2-44 Seat and restraint systems
2
Driver’s seat position sensor
N00417900092
The driver’s seat position sensor is attached to the seat rail and
provides the air bag control unit with information on the seat’s
fore-aft position. The air bag control unit controls deployment
of the driver’s front air bag in accordance with the information
it receives from this sensor.
If there is a problem involving the driver’s seat position sensor,
the SRS warning light in the instrument panel will come on.
Refer to “SRS warning light” on page 2-47.
Passenger’s seat weight sensors
N00418000087
The passenger’s seat weight sensors are attached to the seat
rails and provide the air bag control unit with information
regarding the weight on the front passenger seat. The air bag
control unit controls deployment of the passenger’s front air
bag in accordance with the information it receives from this
sensor.
The passenger’s front air bag will not deploy in an impact
when the weight on the seat is sensed to be less than approxi-
mately 66 pounds (30 kg). In this case, the passenger’s air bag
off indicator will come on.
Refer to “Passenger’s air bag off indicator” on page 2-46.
If there is a problem involving the passenger’s seat weight sen-
sors, the SRS warning light in the instrument panel will come
on. Refer to “SRS warning light” page 2-47.
WA R N I N G
!
If the SRS warning light comes on, have the vehicle
inspected by an authorized Mitsubishi Motors
dealer as soon as possible.
Please observe the following instructions to ensure
that the driver’s seat position sensor can operate
correctly.
• Adjust the seat to the correct position, and sit well
back against the seatback.
Refer to “Front seat” on page 2-4.
• Do not recline the seatback more than necessary
when driving.
• Do not place metallic objects or luggage under the
front seat.

If the vehicle is involved in a severe impact, have the
sensor inspected by an authorized Mitsubishi
Motors dealer as soon as possible.
WA R N I N G
!
If any of the following conditions occur, you should
immediately have your vehicle inspected by an
authorized Mitsubishi Motors dealer as soon as pos-
sible:
• The SRS warning light does not initially come on
when the ignition key is turned to the “ON” or
“START” position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while you are
driving.
BK0121200US.book 44 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

2-46 Seat and restraint systems
2
Passenger’s air bag off indicator
N00418100088
The passenger’s air bag off indicator is located above the cen-
tral vents in the instrument panel.
The indicator normally comes on when the ignition switch is
turned to the “ON” position and goes out a few seconds later.
In the following situations, the indicator will stay on to show
that the passenger’s front air bag is not operational.

The passenger’s seat weight sensors sense a weight of less
than approximately 66 pounds (30 kg) on the front passen-
ger seat.

The front passenger’s seat is not occupied.
When the weight applied to the front passenger seat is sensed
to be approximately 66 pounds (30 kg) or greater, the indicator
goes out to show that the passenger’s front air bag is opera-
tional.
WA R N I N G
!
If any of the following conditions occur, you should
immediately have the air bag system in your vehicle
inspected by an authorized Mitsubishi Motors
dealer as soon as possible:
• The passenger’s air bag off indicator comes on
when an adult is sitting on the front passenger
seat.
• The passenger’s air bag off indicator does not
come on when the front passenger’s seat is not
occupied.
• The passenger’s air bag off indicator does not
come on when the ignition switch is turned to the
“ON” position.
• The passenger’s air bag off indicator comes on and
goes out repeatedly.

Do not attach any accessory to your vehicle that
makes the passenger’s air bag off indicator difficult
or impossible to see.
You must be able to see the passenger’s air bag off
indicator and verify the status of the passenger’s air
bag system.
BK0121200US.book 46 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Seat and restraint systems
2-47
2
SRS warning light
N00408300104
There is a Supplemental Restraint System (SRS) warning light
on the instrument panel. The system checks itself each time the
ignition is turned on.
When the ignition key is in the “ON” or “START” position, the
SRS warning light should come on for several seconds and
then go out. This means the system is working properly.
If there is a problem involving one or more of the SRS compo-
nents, the warning light will come on and stay on.
The SRS warning light is shared by the Supplemental Restraint
System (SRS) and the seat belt pre-tensioner system.
WA R N I N G
!
If any of the following conditions occur, the SRS
and/or seat belt pre-tensioners are not working
properly and you should immediately have it
inspected by an authorized Mitsubishi Motors
dealer:
• The SRS warning light does not come on when the
ignition key is turned to the “ON” or “START”
position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while driving.
BK0121200US.book 47 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

3
Features and controls
Break-in recommendations . . . . . . . . . . . . . . . . . .3- 2
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 2
Electronic immobilizer
(Anti-theft starting system). . . . . . . . . . . . . . . . .3- 3
Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .3- 7
Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 12
Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . .3- 14
“Child safety locks” for rear door . . . . . . . . . . . . .3- 15
Trunk lid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 16
Inside emergency trunk lid release. . . . . . . . . . . . .3- 18
Theft-alarm system (if so equipped) . . . . . . . . . . .3- 20
Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 23
Sunroof (if so equipped) . . . . . . . . . . . . . . . . . . . .3- 26
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 28
Steering wheel tilt lock lever . . . . . . . . . . . . . . . . .3- 29
Inside rearview mirror . . . . . . . . . . . . . . . . . . . . . .3- 30
Outside rearview mirrors . . . . . . . . . . . . . . . . . . . .3- 32
Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 34
Steering wheel lock . . . . . . . . . . . . . . . . . . . . . . . .3- 36
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 37
Automatic transaxle . . . . . . . . . . . . . . . . . . . . . . . .3- 39
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 47
Anti-lock braking system . . . . . . . . . . . . . . . . . . . .3- 49
Active stability control (ASC) . . . . . . . . . . . . . . . .3- 51
Power steering system . . . . . . . . . . . . . . . . . . . . . .3- 56
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 57
Tire pressure monitoring system . . . . . . . . . . . . . .3- 63
Rear-view camera (if so equipped) . . . . . . . . . . . .3- 69Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . . . 3- 72
Indicator and warning light package . . . . . . . . . . . 3- 77
Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 78
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 78
Combination headlights and dimmer switch . . . . . 3- 81
Turn signal lever . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 84
Hazard warning flasher switch . . . . . . . . . . . . . . . 3- 85
Fog light switch (if so equipped). . . . . . . . . . . . . . 3- 86
Instrument panel light dimmer control . . . . . . . . . 3- 87
Wiper and washer switch . . . . . . . . . . . . . . . . . . . 3- 87
Electric rear window defogger switch. . . . . . . . . . 3- 90
Horn switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 91
Hands-free Bluetooth
® cellular phone interface
system with voice recognition (if so equipped) . 3- 92
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 121
Vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 122
Power outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 122
Digital clock (if so equipped) . . . . . . . . . . . . . . . . 3- 123
HomeLink
® Wireless Control System
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 3- 124
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 128
Accessory boxes . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 131
Glove compartment . . . . . . . . . . . . . . . . . . . . . . . . 3- 131
Floor console box/Tissue holder/Pen holders . . . . 3- 132
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 133
Luggage hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 134
Coat hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 134
BK0121200US.book 1 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Features and controls
3-5
3
NOTE
Electronic immobilizer is not compatible with commer-
cially available remote starting systems. Use of commer-
cially available remote starting systems may result in
vehicle starting problems and a loss of security protection.
Use only Mitsubishi Motors authorized accessories.

A system failure is suspected when the ignition key is
turned to the “START” position, and the engine does not
start. In such a case, contact an authorized Mitsubishi
Motors dealer.Replacement keysOnly keys that have been programmed to the vehicle electron-
ics can be used to start the vehicle.
If you lose a key, you can order a key from your authorized
Mitsubishi Motors dealer by referring to the key number.
To prevent vehicle theft, the ID code for the vehicle keys must
be changed.
Take your vehicle and all remaining keys to your authorized
Mitsubishi Motors dealer to have your ID code changed.
Additional keysTo add a key, you need to register the ID code to the vehicle.
Registering the ID code can be done by your authorized
Mitsubishi Motors dealer. Or it can be done by yourself (except
for vehicles sold in Canada).
For you to register the ID code yourself, follow the “Customer
key programming” procedure below.
If you choose to have your authorized Mitsubishi Motors
dealer register the ID code, take your vehicle and any remain-
ing keys to your authorized Mitsubishi Motors dealer.NOTE
You are provided with 2 keys, but you may add up to 6
more keys.Customer key programming (Except for vehicles
sold in Canada)You can program new keys to the system if you have two valid
(already registered) keys and blank (not registered) immobi-
lizer key (specially cut for your vehicle at your Mitsubishi
Motors dealer) by doing the following:
1. Insert the first valid key into the ignition and turn the igni-
tion to the “ON” position for 5 seconds.
2. Turn the ignition to the “LOCK” position and remove the
first key.
3. Within 30 seconds of turning the first key to the “LOCK”
position, insert the second valid key into the ignition and
turn it to the “ON” position. About 10 seconds later, the
immobilizer indicator will start blinking.
CAUTION
!
Do not make any alterations or additions to the
immobilizer system. Alterations or additions could
cause failure of the immobilizer.
BK0121200US.book 5 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

3-6 Features and controls
3
4. When the immobilizer indicator starts blinking, turn the
second valid key to the “LOCK” position and remove it.
Within 30 seconds after doing so, insert a blank immobi-
lizer key into the ignition and turn it to the “ON” position.
Perform this operation no more than 30 seconds after the
immobilizer indicator starts blinking. When registration
of the ID code is complete, the immobilizer indicator will
come on for 3 seconds then go off. If an error occurs, the
immobilizer indicator will go off during the procedure.5. If you wish to register another key, perform the process
again from step 1.
NOTE
It is not possible to register a key if:
• the immobilizer indicator goes off during the procedure
• the immobilizer indicator does not come on for 3 sec-
onds after step 4

The procedure will be terminated automatically if:
• a period of 30 seconds or longer elapses from the
moment when the first key is turned to the “LOCK”
position to the moment when the second key is turned to
the “ON” position
• a period of 30 seconds or longer elapses from the
moment when the second key is turned to the “LOCK”
position to the moment when the blank immobilizer key
(specially cut for your vehicle at your Mitsubishi Motors
dealer) is turned to the “ON” position
• more than 30 seconds elapse after the immobilizer indi-
cator starts blinking
BK0121200US.book 6 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors.
If they are locked while the dome light is not illuminated, the
dome light will blink once. The turn signal lights will also
blink once. NOTE
If you press the LOCK button (1) after locking the doors,
the horn will sound once to confirm that they are locked.To unlock Press the UNLOCK button (2) to unlock the driver’s door only.
Press the UNLOCK button one more time to unlock all the
doors.
If the driver’s door only or all doors are unlocked while the
dome light is not illuminated, the dome light will turn on for 15
seconds. The turn signal lights will also blink twice.To open the trunk lidPress the trunk button (3) twice within 5 seconds and the trunk
lid will be opened. The trunk lid must be closed manually after
it has been opened.NOTE
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.Answerback function The keyless entry system answerback functions from the horn
and turn signal lights can each be turned on or off as desired.
This is done with the key removed from the ignition switch.
NOTE
The answerback function will not operate when the key is
in the ignition switch.Horn deactivation/reactivation The answerback function can be set in the following three
ways.
Each time the answerback function is set, a tone will sound to
tell you the condition of the answerback function.
1. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
2. Release the LOCK and UNLOCK buttons within 10 sec-
onds of pressing the UNLOCK button in step 1.NOTE
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.One chime: The horn will sound if the doors are locked with
the keyless entry system.
Two chimes: The horn will not sound, even if the doors are
locked with the keyless entry system.
Three chimes: The horn will sound if the doors are already
locked and the keyless entry system is used.
In this mode, the horn will only sound when the
keyless entry LOCK button is pressed again to
reconfirm that the doors are locked.
BK0121200US.book 8 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Features and controls
3-9
3
Turn signal light deactivation/reactivation The answerback function from the turn signal lights indicating
when the doors are locked or unlocked can be turned on or off
separately.
A tone will sound once when the function has been turned on,
and twice if it has been turned off.
To deactivate/reactivate the answerback function for lock-
ing of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the LOCK button and then release the UNLOCK
button within 10 seconds of pressing the LOCK button in
step 1.
To deactivate/reactivate the answerback function for
unlocking of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the UNLOCK button and then release the LOCK
button within 10 seconds of pressing the LOCK button in
step 1.NOTE
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.
Using the panic alarmIf you are near your vehicle and feel threatened, you may acti-
vate the alarm to call attention as follows:
1. Press the PANIC button (4) for more than 1 second.
2. The headlights will blink on and off and the horn will
sound intermittently for about 3 minutes.
3. To turn off the alarm, press any button on the remote con-
trol transmitter.NOTE
The indicator light (5) comes on each time a switch is
pressed.

The keyless entry system does not work if the key is in the
ignition.

The remote control transmitter can be used from about 40
feet (12 m) away. However, this distance may change if
your vehicle is near a TV transmitting tower, a power sta-
tion, or a radio station.

If the UNLOCK button (2) is pressed and no door is
opened within approximately 30 seconds: relocking will
automatically occur.
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.

If the following conditions are observed after pressing one
of the buttons of the remote control transmitter, the battery
in the remote control transmitter may need to be replaced.
• The doors cannot be locked or unlocked.
• The trunk lid cannot be opened.
• The panic alarm cannot be operated.
• The indicator light (5) is dim or does not come on.
BK0121200US.book 9 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

3-14 Features and controls
3
To lock the door without using the key 1. Move the inside lock knob to the locked position.
2. Be sure the keys are not inside the vehicle. Close the door. Key reminder buzzer
N00549600136
If you open the driver’s door while the ignition key is in the
“LOCK” or “ACC” position, a tone will sound, reminding you
to remove the key. Lock out protection
N00549700124
If the key is in the ignition switch when you push the lock
knobs forward with the driver’s door or passenger’s door open,
the lock knob will automatically return to the unlocked posi-
tion.
Power door locks
N00509300447
NOTE
Repeated continuous operation between lock and unlock
could activate the power door locking system’s built-in
protection circuit and prevent the system from operating.
If this occurs, wait about 1 minute before operating the
power door lock switch.To lock and unlock by the power door lock switchAll of the doors can be locked or unlocked by pressing the
power door lock switch on the driver’s or the front passenger’s
door. 1- Lock
2- Unlock
BK0121200US.book 14 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

3-20 Features and controls
3Theft-alarm system
(if so equipped)
N00510200042
The theft-alarm system is designed to provide protection from
unauthorized entry into the vehicle. This system is operated in
three stages: the first is the “armed” stage, the second is the
“alarm” stage, and third is the “disarmed” stage. If triggered,
the system provides both audible and visual alarm signals.Armed stage
N00510300072
Park the vehicle and stop the engine. Arm the system as
described below.
1. Remove the key from the ignition switch.
2. Make sure that the engine hood is locked.
3. Lock all doors by using the remote control transmitter.
NOTE
The system is also armed by locking your vehicle using
the following procedures when you leave the vehicle.
• With either the driver’s door or passenger’s door open,
set the inside lock knobs on both doors to the locked
position and then close the door.
• With either the driver’s door or passenger’s door open,
lock all doors using the power door lock switch and then
close the door.
After completion of the steps above, the theft-alarm indicator
(A) will illuminate for approximately 20 seconds and keeps
blinking on and off, indicating that the system is armed.
Arm the system and leave.BK0121200US.book 20 ページ ２０１０年４月１４日　水曜日　午前１１時２４分