isofix MITSUBISHI GRANDIS 2008 Owner's Manual (in English)

2-44 Seat and seat belts
2
NOTE●Before purchasing a child restraint system, try installing it
in the rear seat to make sure there is a good fit. Because of
the location of the seat belt buckles and the shape of the
seat cushion, it may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled forward or to
either side easily on the seat cushion after the seat belt has
been tightened, choose another manufacturer’s child
restraint system.
Depending on the seating position in the vehicle and the
child restraint system that you have, the child restraint can
be attached using one of the following 2 locations:
• To the lower anchorage in the rear seat ONLY if the
child restraint has ISOFIX mountings (See page 2-49).
• To the seat belt (See page 2-51).
Older children
E00406700192
Children who have outgrown the child restraint system should
be seated in the rear seat and wear combination lap shoulder
belt.
The lap portion of the belt should be snug and positioned low
on the abdomen so that it is below the top of the hip-bone. Oth-
erwise, the belt could intrude into the child’s abdomen during
an accident and cause injury.
WARNING
!●Children who are not buckled up can be thrown out
of the vehicle in an accident.●Children who are not buckled up can strike other
people in the vehicle in an accident.●A child should never be left unattended in your vehi-
cle. When you leave the vehicle, take the child with
you.
BK-XP08E1ENUK.en-uk.book Page 44 Monday, August 13, 2007 2:20 PM

2-46 Seat and seat belts
2
L (Genuine part information)


NOTE●The above suitability table applies to retention of child restraints using seat belts.
●When MITSUBISHI MOTORS genuine part No. MZ313045 is used on the intermediate outboad seat, it can also be retained
by means of ISOFIX child restraint mountings.
●There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0- Up to 10 kg (0-9 months)”.
MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For detail information, consult your MITSUBISHI MOTORS Authorized Service Point.
Genuine parts No.
ECE No.
*2
MZ312807 E1-04301146
*
3
MZ312745 E1-04301136
MZ313045 E1-04301133
*
4
MZ312808 E1-04301148
BK-XP08E1ENUK.en-uk.book Page 46 Monday, August 13, 2007 2:20 PM

2-48 Seat and seat belts
2
L (Genuine part information)


NOTE●The above suitability table applies to retention of child restraints using seat belts.
●When MITSUBISHI MOTORS genuine part No. MZ313045 is used on the intermediate outboad seat, it can also be retained
by means of ISOFIX child restraint mountings.
●There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0- Up to 10 kg (0-9 months)”.
MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For detail information, consult your MITSUBISHI MOTORS Authorized Service Point.
Genuine parts No.
ECE No.
*2
MZ312807 E1-04301146
*
3
MZ312745 E1-04301136
MZ313045 E1-04301133
*
4
MZ312808 E1-04301148
BK-XP08E1ENUK.en-uk.book Page 48 Monday, August 13, 2007 2:20 PM

Seat and seat belts
2-49
2
Installing a child restraint system to the lower
anchorage (ISOFIX child restraint mountings)
E00408900042
Your vehicle’s second seat is fitted with lower anchorages for
attaching a child restraint system with ISOFIX mountings.
Child restraint system with ISOFIX mountings
E00409000486
The child restraint system is designed only for seats that incor-
porate lower anchorages. Retain the child restraint system
using the lower anchorages.
It is not necessary to retain the child restraint system using the
vehicle’s seat belts. Only a MITSUBISHI MOTORS genuine
child restraint system can be used.
6-person seat
7-person seat
Genuine parts No.: MZ313045
ECE No.: E1-03301133
A: Child restraint system connectors
BK-XP08E1ENUK.en-uk.book Page 49 Monday, August 13, 2007 2:20 PM

2-50 Seat and seat belts
2
To i n s t a l l
1. Slide the second seats to the fully backward position.
(Refer to “To adjust forward or backward” on page 2-9.)
2. Open the gap a little between the seat cushion (A) and the
seatback (B) with your hand to locate the lower anchor-
ages (C).
3. Push the child restraint system’s connectors into the lower
anchorages (C) in accordance with the instructions pro-
vided by the child restraint system’s manufacturer.
4. Remove the head restraint from the location in which you
wish to install a child restraint.
WARNING
!●If a child restraint system other than a MITSUBI-
SHI MOTORS genuine one is used, it may not be
properly retained and the child could be seriously
injured as a result. Use only a MITSUBISHI
MOTORS genuine child restraint system.
WARNING
!●If there is any foreign material in or around the con-
nectors, remove it before installing the child
restraint system. Also, make sure the seat belt is
away from, not looped through or otherwise inter-
fering with, the child restraint system. If foreign
matter is not removed and/or the seat belt interferes
with the child restraint system, the child restraint
system will not be secured properly and could move
forward in the event of sudden braking or a colli-
sion, seriously injuring the child and possibly other
vehicle occupants.●Use the top tether strap when fitting a child restraint
system with ISOFIX mountings.
Otherwise, the child could be seriously injured in
the event of hard braking or a collision.●When the vehicle is moving do not adjust the seat
where the child restraint system is installed.
BK-XP08E1ENUK.en-uk.book Page 50 Monday, August 13, 2007 2:20 PM