manual radio set MITSUBISHI GRANDIS 2008 Owner's Manual (in English)

General information
5
4. To fill with fuel correctly depends mainly on correct han-
dling of the fuel filler gun. Do not tilt the gun. Insert the
gun in the tank port as far as it goes.
5. When the gun stops automatically, remove the gun half
the way in the tank port. After the second automatic stop,
do not fill with fuel any more.
6. To close, turn the fuel tank filler tube cap slowly clock-
wise until you hear clicking sounds, then gently push the
fuel tank filler door closed.
Installation of accessories
E00200300745
We recommend you to consult your MITSUBISHI MOTORS
Authorized Service Point.
●The installation of accessories, optional parts, etc., should
only be carried out within the limits prescribed by law in
your country, and in accordance with the guidelines fitting
instructions and warnings contained within the documents
accompanying the parts or accessories.
●Improper installation of electrical components may cause
an electrical fire if incorrectly fitted. Please refer to the
Modification/alteration to the electrical or fuel systems
section within this owner’s manual.
●Using a cellular phone or radio set inside the vehicle with-
out an external antenna may cause electrical system inter-
ference, which could lead to unsafe vehicle operation.
●Tyres and wheels which do not meet specifications must
not be used.
Refer to the “Specifications” section for information
regarding wheel and tyre sizes.
CAUTION
!●A label which reads “UNLEADED FUEL ONLY” is
attached to the fuel tank filler lid of vehicles which
can only operate using unleaded petrol. Serious
engine and catalytic converter damage will result if
leaded petrol is filled into these vehicles, and conse-
quently, this must never be attempted.
CAUTION
!●To avoid fuel spillage and overfilling, do not “top-
off” the fuel tank.
CAUTION
!●If you need to replace the fuel tank filler tube cap,
use only the cap specified for your model vehicle.
BK-XP08E1ENUK.en-uk.book Page 5 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-19
3
3. Make your selection by pressing the “ ” button or the
“ ” button.NOTE●After selecting a mode, you can leave the function setup
mode by taking either of the following steps:
• Press the “MENU” button for at least 2 seconds.
• Make no entry for 7 seconds.
Automatic mode (For vehicles with MITSUBISHI
MOTORS genuine audio)The automatic mode can set the local time automatically by
using the signal from the local RDS stations. In this mode, CT
(A) is shown in the display. Refer to “Radio data system
(RDS)” on page 5-29.
- CT ON (Automatic mode)
- CT OFF (Manual mode)
BK-XP08E1ENUK.en-uk.book Page 19 Monday, August 13, 2007 2:20 PM

3-20 Instruments and controls
3
Manual modeThe manual mode is also available in case the “Automatic
mode” shows the incorrect time when the adjacent local RDS
stations are located in a different time zone. Refer to “Radio
data system (RDS)” on page 5-29.
Set the time by pressing the various buttons as described
below.
Outside temperature
E00503900019
This value shows the outside temperature of the vehicle.
If the outside air temperature drops below approx. 3 °C, the
alarm sounds and the outside air temperature figure flashes for
about 10 seconds.
H- To adjust the hour
M- To adjust the minutes
SET- To reset the minutes to zero
10:30-11:29...Changes to 11:00
11:30-12:29...Changes to 12:00
CAUTION
!●There is a danger the road might be icy, even when
the outside air temperature figure is not flashed, so
please take care when driving.
BK-XP08E1ENUK.en-uk.book Page 20 Monday, August 13, 2007 2:20 PM

For pleasant driving
5-27
5
To listen to the radio
E00709000678
1. Press the PWR switch (5) to turn the audio system on and
off. The system turns on in the last mode used.
2. Press the AM/FM button (1) to select the desired band.
3. Press the TUNE/SEEK button (2 or 3) to turn to a station,
or press one of the memory select buttons (4) to recall a
station memorised for that button.To tune the radio
E00709100565
Automatic tuning
After keeping the TUNE/SEEK button (2 or 3) depressed until
it beeps, release the button, and the selected station reception
will start.
Manual tuning
The frequency changes every time the TUNE/SEEK button
(2 or 3) is pressed. Press the button to select the desired station.
To enter frequencies into the memory
E00716100785
Manual setting
You can assign to the memory select buttons (4) a maximum of
18 stations in the FM band (6 FM1, 6 FM2 and 6 FM3 stations)
and 6 stations each in the MW and LW band. (Stations already
assigned to the memory select buttons are replaced by any
newly assigned stations.)
BK-XP08E1ENUK.en-uk.book Page 27 Monday, August 13, 2007 2:20 PM

5-28 For pleasant driving
5
Follow the steps described below.
1. Press either the TUNE/SEEK button (2 or 3) to tune the
frequency to be entered in the memory.
2. Press one of the memory select buttons (4) for 2 seconds
or longer. The sound will be momentarily interrupted
while the frequency is being entered into the memory.
The number of the button corresponding to the entry in the
memory and the frequency are displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within 2 seconds.
Automatic setting
With the method, all manually set stations in the band currently
selected for reception are replaced with stations in the same
band that are automatically selected in order of signal strength.
The radio automatically selects 6 stations in the FM band (FM3
station only) and 6 stations each in the MW and LW band.
Follow the steps described below.
1. With the radio mode selected, hold down the AM/FM but-
ton (1) for 2 seconds or longer. The 6 stations with the
best signal strength will automatically be assigned to the
memory select buttons (4), with the lowest-frequency sta-
tion being assigned to the lowest-number button.
2. When you subsequently press a memory select button to
select a channel number, the radio will begin receiving the
station assigned to that number.NOTE●If you press the AM/FM button (1) for 2 seconds or longer
while tuning in the FM1 or FM2 band, the radio will auto-
matically switch to the FM3 band, where the automatic
seeking/storing will be activated.
BK-XP08E1ENUK.en-uk.book Page 28 Monday, August 13, 2007 2:20 PM

5-30 For pleasant driving
5
RDS uses PI (program identification) signal and AF (alterna-
tive frequency) list transmitted in addition to the normal FM
broadcasting programs, and picks up the FM stations that are
transmitting the same program from the EON (enhanced other
network) and automatically tunes to the station with the strong-
est signal intensity.
Therefore, you can continue listening to one program in, for
example, a long distance driving without retuning to the other
station transmitting the same program when you are leaving
the service area of the currently receiving station.
The RDS radio also features the limited reception of the pro-
gram types, the break-in reception of the traffic announcement
and emergency broadcast, and the limited/unlimited reception
of the regional programs.AF (Alternative Frequencies) function
E00720900016
The AF function finds a station broadcasting the same program
and selects the station with the strongest signal of AF lists.
The AF function is turned on (with the AF indicator (9) shown
on the display) at all times unless you manually switch it off.
The AF function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-35.CT (Clock Time) function
E00721000014
The clock can be set automatically by using the signal from the
local RDS stations. Refer to “Digital clock” on page 3-17.
REG (Regional) function
E00721100015
REG function limits to receive the stations broadcasting
regional programs.
Regional programming and regional networks are organized
differently depending on the country or area (they may be
changed according to the hour, state, or broadcast area), so if
you don’t want to receive the regional programs automatically,
you can set up REG ON not to receive regional programs.
The REG function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-35.PI (Program Identification) search function
E00721200016
When travelling long distance and the recalled preset station is
weak, the radio searches another frequency broadcasting the
same programming with the same PI code in AF list.
If there are no frequencies broadcasting the same program-
ming, the radio searches a frequency broadcasting the regional
programming. The radio succeeds in searching the regional
programming, then the display shows the REG indicator (11).
If the radio does not succeed in searching the regional pro-
gramming, the radio returns to the recalled preset station.PTY (Program type)
E00721300192
RDS broadcasts are classified according to program type
(PTY) as follows. Use the TUNE/SEEK button (5 or 6) to
select your desired PTY.
BK-XP08E1ENUK.en-uk.book Page 30 Monday, August 13, 2007 2:20 PM