warning light MITSUBISHI iMiEV 2012 1.G User Guide

Seat and restraint systems
2-17
2
NOTE
With the exception of the seat belt for the driver, the seat
belts in all other seating positions are equipped with an
Automatic Locking Retractor (ALR) function. If you pull
the seat belt fully out of the retractor, the retractor will
switch to its ALR child restraint installation function (see
page 2-31).
When the ALR function has been activated, the seat belt
will only retract. If this happens, let the belt fully retract,
then pull the seat belt back out, repeating steps 1 through
4.
5. To release the belt, press the button on the buckle and
allow the belt to retract.
If the belt does not retract smoothly, pull it out and check
for kinks or twists in the webbing. Then make sure it
remains untwisted as it retracts.
Driver’s seat belt reminder/warning light
N00418400371
A tone and warning light are used to remind the driver to fasten
the seat belt.
If the electric motor switch is turned to the “ON” position with-
out the driver’s seat belt being fastened, a warning light will
come on, and a tone will sound for approximately 6 seconds to
remind you to fasten your seat belt.
If the seat belt remains unfastened approximately 1 minute
later, the warning light will flash and the tone will sound inter-
mittently for approximately 90 seconds when the vehicle is
driven.
If the seat belt subsequently remains unfastened, the warning
light and tone will issue further warnings each time the vehicle
starts moving from a stop. And if the driver unfastens the seat
WA R N I N G
!
Be sure the lap belt portion fits snugly and is worn
as low as possible across the hips, not around the
waist. Failure to follow this instruction will increase
the risk of serious injury or death in the event of an
accident.
Be sure the seat belt webbing is not twisted when
worn. Twisted webbing may adversely affect seat
belt performance.
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-18 Seat and restraint systems
2
belt while driving, the warning will operate in the same way.
When the seat belt is fastened, the warnings will stop.
Front passenger seat belt warning light
N00418300224
The front passenger seat belt warning light is located in the
instrument panel.
When the electric motor switch is turned to the “ON” position,
this indicator normally comes on and goes off a few seconds
later.
The light comes on when a person sits on the front passenger
seat but does not fasten the seat belt.
It goes off when the seat belt is subsequently fastened.
WA R N I N G
!
In order to reduce the risk of serious injury or death
in an accident, always wear your own seat belt. Do
not allow anyone to ride in your vehicle unless he or
she is also seated and wearing a seat belt. Children
should additionally be restrained in a secure child
restraint system.
WA R N I N G
!
When a child booster seat is used on the front pas-
senger seat, the front passenger seat belt warning
light will not come on, if the seat belt is not fastened
when the booster seat is used. Confirm that the child
is wearing the seat belt properly.
BK0140800US.book 18 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-22 Seat and restraint systems
2
The seat belt pre-tensioner system includes the following com-
ponents:
The airbag control unit monitors the readiness of the electronic
parts of the system whenever the electric motor switch is in the
“ON” or “START” position. These include all of the items
listed above and all related wiring.
The pre-tensioner seat belt system will operate only when the
electric motor switch is in the “ON” or “START” position.When the seat belt pre-tensioners activate, some smoke is
released and a loud noise will be heard. The smoke is not harm-
ful, but care should be taken not to intentionally inhale it, as it
may cause some temporary irritation to people with respiratory
problems.
The pre-tensioners activate in the event of a moderate-to-
severe front or side impact, even if the seat belt is not being
worn. The seat belt pre-tensioners may not activate in certain
frontal collisions, even though the vehicle may appear to be
severely damaged. Such non-activation does not mean some-
thing is wrong with the seat belt pre-tensioner system, but
rather that the collision forces were not severe enough or not of
the type to activate the system.
SRS warning light
N00408700124
This warning light tells you if there is a problem involving the
SRS airbags and/or the pre-tensioner seat belts. Refer to “SRS
warning light” on page 2-44.
1- SRS warning light
2- Front impact sensors
3- Seat belt pre-tensioners
4- Airbag control unit
WA R N I N G
!
The seat belt pre-tensioner system is designed to
work only once. After the seat belt pre-tensioners
have been activated, they will not work again. They
must promptly be replaced and the entire seat belt
pre-tensioner system inspected by a certified i-MiEV
dealer.
BK0140800US.book 22 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-39
2
How the Supplemental Restraint System works
N00407800489
The SRS includes the following components:
The airbag control unit monitors the readiness of the electronic
parts of the system whenever the electric motor switch is in the
“ON” or “START” position. These include all of the items
listed above and all related wiring.
The airbags will operate only when the electric motor switch is
in the “ON” or “START” position. 1- Driver’s airbag
2- SRS warning light
3- Passenger’s airbag off indicator
4- Front impact sensors
5- Passenger’s front airbag
6- Driver’s seat position sensor
7- Passenger’s seat occupant classification sensor system
8- Airbag control unit
9- Side airbag modules
10- Curtain airbag modules
11- Side impact sensors
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-41
2
Driver’s seat position sensor
N00417900210
The driver’s seat position sensor is attached to the seat rail and
provides the airbag control unit with information on the seat’s
fore-aft position. The airbag control unit controls deployment
of the driver’s front airbag in accordance with the information
it receives from this sensor.
If there is a problem involving the driver’s seat position sensor,
the SRS warning light in the instrument panel will come on.
Refer to “SRS warning light” on page 2-44.
Passenger’s seat occupant classification sensor
system
N00418000348
The passenger’s seat occupant classification sensor system is
attached to the front passenger seat cushion and provides the
airbag control unit with information regarding the occupant on
the front passenger seat. The airbag control unit controls
deployment of the passenger’s front airbag in accordance with
the information it receives from this system.
The passenger’s front airbag will not deploy in an impact when
the system senses no occupant on the front passenger’s seat or
a child in a child restraint system. In this case, the passenger’s
airbag off indicator will come on.
Refer to “Passenger’s airbag off indicator” on page 2-43.
If there is a problem involving the passenger’s seat occupant
classification sensor system, the SRS warning light in the
instrument panel will come on. Refer to “SRS warning light”
page 2-44.
WA R N I N G
!
If the SRS warning light comes on, have the vehicle
inspected by a certified i-MiEV dealer as soon as
possible.
Please observe the following instructions to ensure
that the driver’s seat position sensor can operate
correctly.
• Adjust the seat to the correct position, and sit well
back against the seatback.
Refer to “Front seats” on page 2-3.
• Do not recline the seatback more than necessary
when driving.
• Do not place metallic objects or luggage under the
front seat.

If the vehicle is involved in a severe impact, have the
SRS sensor inspected by a certified i-MiEV dealer as
soon as possible.
WA R N I N G
!
If any of the following conditions occur, you should
immediately have your vehicle inspected by a certi-
fied i-MiEV dealer as soon as possible:
• The SRS warning light does not initially come on
when the electric motor switch is turned to the
“ON” or “START” position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while you are
driving.
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-44 Seat and restraint systems
2
SRS warning light
N00408300566
There is a Supplemental Restraint System (SRS) warning light
on the instrument panel. The system checks itself each time the
electric motor switch is turned on. When the electric motor
switch is in the “ON” or “START” position, the SRS warning
light should come on for several seconds and then go out. This
means the system is working properly. If there is a problem
involving one or more of the SRS components, the warning
light will come on and stay on. The SRS warning light is
shared by the Supplemental Restraint System (SRS) and the
seat belt pre-tensioner system.
WA R N I N G
!
If any of the following conditions occur, the SRS
and/or seat belt pre-tensioners are not working
properly and you should immediately have it
inspected by a certified i-MiEV dealer:
• The SRS warning light does not come on when the
electric motor key is turned to the “ON” or
“START” position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while driving.
BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3
Features and controls
Break-in recommendations . . . . . . . . . . . . . . . . . .3- 2
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 2
Electronic immobilizer
(Anti-theft starting system). . . . . . . . . . . . . . . . .3- 3
Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .3- 7
Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 12
Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . .3- 14
Child safety locks for rear door . . . . . . . . . . . . . . .3- 15
Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 16
Theft-alarm system . . . . . . . . . . . . . . . . . . . . . . . .3- 18
Power window control . . . . . . . . . . . . . . . . . . . . . .3- 22
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 25
Inside rearview mirror . . . . . . . . . . . . . . . . . . . . . .3- 26
Outside rearview mirrors . . . . . . . . . . . . . . . . . . . .3- 28
Electric motor switch . . . . . . . . . . . . . . . . . . . . . . .3- 30
Steering wheel lock . . . . . . . . . . . . . . . . . . . . . . . .3- 32
Starting the electric motor unit. . . . . . . . . . . . . . . .3- 33
Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 33
Acoustic vehicle alerting system (AVAS) . . . . . . .3- 38
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 39
Brake assist system . . . . . . . . . . . . . . . . . . . . . . . .3- 40
Anti-lock braking system . . . . . . . . . . . . . . . . . . . .3- 41
Electric power steering system (EPS) . . . . . . . . . .3- 44Active stability control (ASC). . . . . . . . . . . . . . . . 3- 46
Tire pressure monitoring system . . . . . . . . . . . . . . 3- 49
Rear-view camera (if so equipped) . . . . . . . . . . . . 3- 55
Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . . . 3- 58
Indicator and warning light package . . . . . . . . . . . 3- 71
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 72
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 73
Combination headlights and dimmer switch . . . . . 3- 76
Turn signal lever . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 82
Hazard warning flasher switch . . . . . . . . . . . . . . . 3- 83
Front fog light switch (if so equipped) . . . . . . . . . 3- 83
Wiper and washer switch . . . . . . . . . . . . . . . . . . . 3- 84
Electric rear window defogger switch. . . . . . . . . . 3- 89
Horn switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 90
Link System (if so equipped) . . . . . . . . . . . . . . . . 3- 90
Bluetooth
® 2.0 interface (if so equipped) . . . . . . . 3- 91
USB input terminal (if so equipped) . . . . . . . . . . . 3- 117
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 122
12 V power outlet . . . . . . . . . . . . . . . . . . . . . . . . . 3- 123
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 124
Storage spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 128
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 130
Assist grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 131
BK0140800US.book 1 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-25
3 Parking brake
N00511400386
To park the vehicle, first bring it to a complete stop, fully
engage the parking brake, and set the selector lever to “P”
(PARK) position.To apply To release
When parking on a hill, apply the parking brake and turn the
front wheels toward the curb on a downhill grade, away from
the curb on an uphill grade.
1- Pull the lever up without pushing the button at the end of
hand grip.
When the parking brake is set and the electric motor switch
is in the “ON” position, the brake warning light in the instru-
ment cluster will come on.
Before driving, be sure to release the parking brake.
1- Pull the lever up slightly.
2- Press and hold the button at the end of the hand grip.
3- Push the lever downward.
CAUTION
!
Before driving, be sure that the parking brake is
fully released and brake warning light is off.
If a vehicle is driven without releasing the parking
brake, the brakes will be overheated, resulting in
ineffective braking and possible brake failure.
BK0140800US.book 25 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-33
3 Starting the electric motor unit
N00571800014
1. Make sure all occupants are properly seated with seat
belts fastened.
2. Insert the key.
3. Make sure the parking brake is applied.
4. Press and hold the brake pedal down with your right foot.
5. Make sure the selector lever is in the “P” (PARK) posi-
tion.
6. Turn the key to the “ON” position and make certain that
all warning lights are functioning properly before starting
the electric motor unit.
7. Turn the key to the “START” position for one to two sec-
onds, and slowly return it to its original position. When
you hear the startup sound and the ready indicator comes
on, startup of the electric motor unit is complete.Electric motor reminderIf the driver’s door is opened while the key is in the “ON” posi-
tion, the electric motor reminder buzzer sounds intermittently
to remind the key is in the electric motor switch.
Transmission
N00513200203
Selector lever operation
N00513800371
CAUTION
!
Never attempt to start the electric motor unit by
pushing or pulling the vehicle.
While depressing the brake pedal, move the selector
lever through the gate.
Move the selector lever through the gate.
BK0140800US.book 33 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-39
3 Service brake
N00517500305
Brake pedalOveruse of the brake can cause poor brake response and pre-
mature wear of the brake pads.
Power brakes
N00517600410
Your vehicle is equipped with power brakes for more braking
force with reduced brake pedal effort.
Your brakes are designed to operate at full capacity, even if the
power assist is lost.
If the power assist is lost, the effort needed to press the brake
pedal is greater.
If you should lose the power assist for some reason, the brakes
will still work.
If the power brake unit or either of the two brake hydraulic sys-
tems stop working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to
depress the brake pedal down further, or harder when slowing
down or stopping, or if the brake warning light comes on.
WA R N I N G
!
Do not leave any objects near the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that would be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
CAUTION
!
It is important not to drive the vehicle with your foot
resting on the brake pedal when braking is not
required. This practice can result in very high brake
temperatures, premature pad wear, and possible
damage to the brakes.
WA R N I N G
!
Never turn off the electric motor switch while driv-
ing. Doing so will result in a loss of power assist for
the brakes and steering, increasing the effort
required to steer and brake the vehicle.
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分