brake light MITSUBISHI iMiEV 2012 1.G Owner's Manual

3-78 Features and controls
3
Vehicles equipped with daytime running lights
[When the ready indicator is illuminated, and the parking brake
is released]
The daytime running lights will be illuminated:NOTE
Once the daytime running light come on, they do not go
out until the electric motor switch is turned to the
“LOCK” or “ACC” position.[When the ready indicator is not illuminated, or when the ready
indicator is illuminated but the parking brake is not released]
The electric motor unit starts when the lights are off.OFF The daytime running lights illuminated
AUTOThe daytime running lights illuminated
Headlights and other lights turn on and off automati-
cally in accordance with outside light level.
The daytime running lights illuminated
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
OFF All lights off
AUTOHeadlights and other lights turn on and off automati-
cally in accordance with outside light level.
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0140800US.book 78 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-8 Driving safety
4Braking
N00629500518
All the parts of the brake system are critical to safety. Have the
vehicle serviced by a certified i-MiEV dealer at regular inter-
vals according to the “WARRANTY AND MAINTENANCE
MANUAL”.When brakes are wetCheck the brake system while driving at a low speed immedi-
ately after starting, especially when the brakes are wet, to con-
firm they work normally.
A film of water can be formed on the brake discs and prevent
normal braking after driving in heavy rain or through large
puddles, or after the vehicle is washed. If this occurs, dry the
brakes out by driving slowly while lightly depressing the brake
pedal.When driving in cold weatherOn snowy roads, ice can form on the braking system, making
the brakes less effective. While driving in such conditions, pay
close attention to preceding and following vehicles and to the
condition of the road surface. From time to time, lightly
depress the brake pedal and check how effective the brakes are.When driving downhillIt is important to take advantage of the regenerative braking by
shifting to “B” (BRAKE) position while driving on steep
downhill roads in order to prevent the brakes from overheating.
Parking
N00629600317
Parking on a hillWhen parking on a hill, set the parking brake, and turn the
front wheels toward the curb on a downhill, or away from the
curb on an uphill.
If necessary, apply chocks to wheels.NOTE
On a slope, be sure to apply the parking brake before
moving the selector lever to the “P” (PARK) position. If
you move the selector lever to the “P” (PARK) position
before applying the parking brake, it may be difficult to
disengage the selector lever from the “P” (PARK) position
when next you drive the vehicle, requiring application of a
strong force to the selector lever to move from the “P”
(PARK) position.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

6-2 For emergencies
6If the vehicle breaks down
N00836300220
If your vehicle breaks down on the road, move to the shoulder
and turn on the hazard warning flashers. If there is no shoulder,
or the shoulder is not safe, drive in the right lane slowly, with
the hazard lights flashing, until you come to a safe stopping
place. Keep the flashers flashing.
If the ready indicator light goes out while driving, the brakes
and steering will continue to work, but without power assist, so
more effort will be required for braking and steering. Stop the
vehicle on the shoulder of the road and turn on the hazard
warning flashers.
Jump-starting
N00836400739
If the electric motor unit cannot be energized because the 12V
starter battery is weak or dead, you can start it with the battery
from another vehicle using jumper cables. NOTE
Do not use jumper cables if they have damage or corro-
sion.
1. Take off any metal jewelry such as watch bands or brace-
lets that might make an accidental electrical contact.
WA R N I N G
!
To reduce the risk of igniting flammable gas that
may be emitted from the 12V starter battery, care-
fully read this section before jump-starting the vehi-
cle.
Do not try to start the electric motor unit by pushing
or towing the vehicle. This can cause an accident
resulting in serious injury or death and can damage
the vehicle.
CAUTION
!
Do not attempt jump starting the 12V starter bat-
tery while the main drive lithium-ion battery is
being charged. Doing so could damage the vehicle or
charging equipment.
BK0140800US.book 2 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-3
6
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles are not
touching each other.
3. Set the parking brake firmly on your vehicle and move the
selector lever into the “P” (PARK) position.
4. Set the parking brake firmly on the other vehicle. Put the
automatic transaxle in “P” (PARK) or the manual
transaxle in “N” (Neutral).
5. Turn the ignition switch (the electric motor switch) on
each vehicle to the “LOCK” position.NOTE
Turn off all lights, heater, and other electrical loads. This
will help avoid sparks.6. Remove the battery cover, and then make sure your 12V
starter battery electrolyte is at the proper level. (Refer to
“Checking 12V starter battery electrolyte level” on page
7-14.)
7. Connect one end of one jumper cable to the positive
(+) terminal of the discharged battery (A), and then con-
nect the other end to the positive (+) terminal of the
booster battery (B).
CAUTION
!
Check the other vehicle. It must have a 12V battery.
If the other system is not 12V, both systems can be
damaged.
WA R N I N G
!
If the electrolyte fluid is not visible, or looks frozen,
DO NOT ATTEMPT JUMP STARTING!!
The battery might split open or explode if the tem-
perature is below the freezing point or if it is not
filled to the proper level.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-7
6
As your vehicle has anti-lock brakesIf you drive your vehicle with a low battery charge, after the
electric motor unit has been started by using jumper cables, it
can cause the anti-lock braking system warning light to illumi-
nate. This is only due to the low battery voltage. It is not a
problem with the brake system. If this happens, fully charge the
12V starter battery and ensure the charging system is operating
properly.
Tire repair kit
N00836600366
This vehicle is equipped with a tire repair kit which can be
used to repair a minor puncture in tread area caused by a nail,
screw or similar object. A spare tire is not provided with this
vehicle.
WA R N I N G
!
The tire repair kit may not permanently seal a punc-
tured tire.
Using the tire repair kit may damage the wheel
and/or the tire inflation pressure sensor for the tire.
The vehicle must promptly be inspected and
repaired by a certified i-MiEV dealer after using the
tire repair kit.
Use only the Mitsubishi genuine tire repair kit. Seal-
ant in other repair kits may not sufficiently seal the
tire puncture.
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分

6-22 For emergencies
6Operation under adverse driving conditions
N00837200747
If your vehicle becomes stuck in sand, mud or
snow If your vehicle becomes stuck in snow, sand, or mud, it can
often be moved by a rocking motion. Rock your vehicle back
and forth to free it.
Do not spin the wheels. Constant efforts to free a stuck vehicle
can cause transmission failure.
If your vehicle is still stuck after several rocking attempts, call
for a commercial tow truck service.
On wet roads
WA R N I N G
!
When trying to rock your vehicle out of a stuck posi-
tion, make sure that there are no people nearby. The
rocking motion can make your vehicle suddenly
lurch forward or backward, and injure any
bystanders.
CAUTION
!
Do not drive on a flooded road. If you drive on a
flooded road, not only the electric motor unit stops
but also a failure like electric leakage or short circuit
may occur.
If you inevitably had to run on a flooded road and
the vehicle was exposed to water, be sure to have
your vehicle inspected by a certified i-MiEV dealer.
When driving in rain, on water-covered roads, or
through a car wash, water could get into the brake
discs and make them fail temporarily. In such cases,
lightly press the brake pedal to see if they are work-
ing properly. If they are not, press the pedal lightly
several times while driving to dry the brake pads or
linings, then check them again.
When driving in rain, a layer of water may form
between the tires and the road surface (aquaplan-
ing). This loosens your tires’ grip on the road, mak-
ing it difficult to steer or brake properly. When
driving on a wet road:
• Drive your vehicle at a safe speed.
• Do not drive on worn tires.
• Always keep the tires at the correct inflation pres-
sures.
BK0140800US.book 22 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7
Vehicle care and maintenance
Service precautions . . . . . . . . . . . . . . . . . . . . . . . .7- 2
Hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 4
View under the hood and
electric motor unit room . . . . . . . . . . . . . . . . . . .7- 6
Coolant/Hot water heater fluid. . . . . . . . . . . . . . . .7- 7
Washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 11
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 12
12V starter battery . . . . . . . . . . . . . . . . . . . . . . . . .7- 13
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 18
Brake pedal free play . . . . . . . . . . . . . . . . . . . . . . .7- 25
Parking brake lever stroke . . . . . . . . . . . . . . . . . . .7- 25
Wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 26
General maintenance . . . . . . . . . . . . . . . . . . . . . . .7- 27
For cold and snowy weather . . . . . . . . . . . . . . . . .7- 28
Fusible links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 28
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- 29
Replacement of light bulbs . . . . . . . . . . . . . . . . . .7- 35
Vehicle care precautions . . . . . . . . . . . . . . . . . . . .7- 49
Cleaning the inside of your vehicle . . . . . . . . . . . .7- 50
Cleaning the outside of your vehicle . . . . . . . . . . .7- 52
BK0140800US.book 1 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-12 Vehicle care and maintenance
7Brake fluid
N00938700261
To check the fluid levelThe brake fluid level must be between the “MAX” and “MIN”
marks on the reservoir.
The brake fluid level falls slightly with wear of the brake pads,
but this does not indicate any abnormality.
The brake fluid in the master cylinder should be checked when
doing other work under the hood. The brake system should also
be checked for leaks at the same time.
If the brake fluid level falls markedly in a short length of time,
it indicates a leak in the brake system.
If this occurs, have the vehicle checked by a certified i-MiEV
dealer.
Fluid typeUse the recommended brake fluid conforming to DOT 3 or
DOT 4. The reservoir cap must be tightly sealed to keep dirt
and water out.
CAUTION
!
Do not let any petroleum-based fluid touch, mix
with, or get into the brake fluid. This will damage
the seals.
Be careful when handling brake fluid. It can damage
painted surfaces.
Use only the listed brake fluid. Different brands of
brake fluid have different additives, and these can
cause a chemical reaction. Do not mix brands of
brake fluid.
Keep the reservoir tank cap closed to keep the brake
fluid from evaporating.
BK0140800US.book 12 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-27
7 General maintenance
N00941500289
The next pages list the maintenance service recommended by
Mitsubishi Motors Corporation. In addition to the general
maintenance that needs to be performed at the times listed,
there are other parts which do not usually need regular mainte-
nance.
But, if any of these parts stops working properly, your vehicle
performance could suffer. Have these items checked if you
notice a problem with them.
See a certified i-MiEV dealer for assistance, if you have any
questions.Disc brake pads, rear drum brake linings and
rear wheel cylinders
N00941600033
Good brakes are essential to safe driving. Check the brake pads
and brake linings for wear and check the rear wheel cylinders
for leaks. For good braking performance, replace the brake
pads with the same type pads as the originals.Brake hoses
N00941700047
Brake hoses and tubing should be checked for:

Severe surface cracking, scuffing or worn spots. If the
fabric casing of the hose is showing through any cracks or
worn spots in the rubber hose cover, the hose should be
replaced. The brakes can fail if the hose wears through.

Improper installation may cause twisting, or wheel, tire or
chassis interference.
Ball joint, steering linkage seals and drive shaft
boots
N00941800077
Check the following parts for damage and grease leaks:

Ball joint boots of the front suspension and steering link-
age

Bellows on both ends of the drive shaftHood lock release mechanism and safety catch
N00942500114
The hood lock release mechanism and hood safety catch should
be checked, cleaned, and oiled when needed for easy move-
ment and to stop rust and wear. Use Multipurpose Grease
NLGI Grade 2 sparingly for all sliding parts of the hood latch
and release lever. Work the grease into the hood lock mecha-
nism until all the movable surfaces are covered.
Also, put a light coat of the same grease on the safety catch
wherever moving parts touch.
BK0140800US.book 27 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-32 Vehicle care and maintenance
7
Under the hood fuse location table
*: Fusible link

Some fuses may not be installed on your vehicle, depend-
ing on the vehicle model or specifications.

The table above shows the main equipment corresponding
to each fuse.
No.
Symbol
Electrical system
Capacity
1— — —
2 12V starter battery 30 A*
3 Electric motor switch 40 A*
4 Radiator fan motor 40 A*
5 Power window control 40 A*
6 Brake electric vacuum pump 30 A*
7 Electric motor unit control 15 A
8 Stop lights (Brake lights) 15 A
9 Front fog lights 15 A
10Wa t e r p u m p
(Electric motor unit)15 A
11 Charge 10 A
12 Hazard warning flasher 10 A
13 Horn 10 A
14 Daytime running lights 10 A
15Main drive lithium-ion bat-
tery fan motor15 A
16Wa t e r p u m p
(Air conditioning)10 A
17 Headlight (low beam) (right) 20 A
18 Headlight (low beam) (left) 20 A
19 Headlight (high beam) (right) 10 A
20 Headlight (high beam) (left) 10 ANo.
Symbol
Electrical system
Capacity
BK0140800US.book 32 ページ ２０１１年９月２９日　木曜日　午後３時２８分