brake MITSUBISHI iMiEV 2012 1.G Service Manual

3-130 Features and controls
3Cup holder
N00527300364
For the front seatThe cup holder is located in front of the side vent.
The cup holder is designed for holding cups or drink-cans
securely in its holes.
Tip the cup holder toward you to use it.NOTE
When not using the holder, push the holder in to stow it
away.
Do not put your hand on the cup holder while getting in or
out of the vehicle. The cup holder could break.

Never place anything other than cup or drink can in the
cup holder.
For the rear seat
N00537000146
This cup holder is located behind the parking brake lever.
CAUTION
!
Do not drink beverages while driving your vehicle.
This is distracting and could cause an accident.
BK0140800US.book 130 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-4 Driving safety
4
3. Secure the floor mat with retaining clips.NOTE
The shape of the mat and the number of retaining clips
may vary depending on the vehicle model.
WA R N I N G
!
If a floor mat is the wrong size or is not properly
installed, it can interfere with the operation of the
pedals. Interference with the pedals can cause unin-
tended acceleration and/or increased stopping dis-
tances resulting in a crash and injury. Always make
sure the floor mat does not interfere with the accel-
erator or brake pedal.
Always use the retaining clip on the driver’s floor-
board to secure the floor mat.

Always install the mat with the correct side facing
down.
Never install a second mat over or under an existing
floor mat.
Do not use a floor mat designed for another model
vehicle even if it is a Mitsubishi genuine floor mat.
Before driving, be sure to check the following:
• Periodically check that the floor mat is properly
secured with the retaining clips.
If you remove the floor mat while cleaning the
inside of your vehicle or for any other reason,
always check the condition of the floor mat after it
has been reinstalled.
• While the vehicle is stopped with the electric motor
unit off, check that the floor mat is not interfering
with the pedals by depressing the pedals fully.WA R N I N G
!
BK0140800US.book 4 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Driving safety
4-5
4 Vehicle preparation before driving
N00629000698
For a safer and more enjoyable trip, always observe the follow-
ing: Seat belts and seats
Before starting the vehicle, make certain that you and all
passengers are seated and wearing their seat belts properly
(with children in the rear seat, in appropriate restraints),
and that all the doors and the rear hatch are locked.

Move the driver’s seat as far backward as possible, while
still keeping good visibility, and good control of the steer-
ing wheel, brakes, accelerator, and controls. Check the
instrument panel indicators for any possible problem.

Move the front passenger seat as far back as possible.

Make sure that infants and small children are properly
restrained in accordance with all laws and regulations.DefrostersCheck these by selecting the defroster mode, and set the blower
switch on high. You should be able to feel the air blowing
against the windshield.
(Refer to “Defrosting or defogging the windshield and door
windows” on page 5-15.)
BK0140800US.book 5 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-8 Driving safety
4Braking
N00629500518
All the parts of the brake system are critical to safety. Have the
vehicle serviced by a certified i-MiEV dealer at regular inter-
vals according to the “WARRANTY AND MAINTENANCE
MANUAL”.When brakes are wetCheck the brake system while driving at a low speed immedi-
ately after starting, especially when the brakes are wet, to con-
firm they work normally.
A film of water can be formed on the brake discs and prevent
normal braking after driving in heavy rain or through large
puddles, or after the vehicle is washed. If this occurs, dry the
brakes out by driving slowly while lightly depressing the brake
pedal.When driving in cold weatherOn snowy roads, ice can form on the braking system, making
the brakes less effective. While driving in such conditions, pay
close attention to preceding and following vehicles and to the
condition of the road surface. From time to time, lightly
depress the brake pedal and check how effective the brakes are.When driving downhillIt is important to take advantage of the regenerative braking by
shifting to “B” (BRAKE) position while driving on steep
downhill roads in order to prevent the brakes from overheating.
Parking
N00629600317
Parking on a hillWhen parking on a hill, set the parking brake, and turn the
front wheels toward the curb on a downhill, or away from the
curb on an uphill.
If necessary, apply chocks to wheels.NOTE
On a slope, be sure to apply the parking brake before
moving the selector lever to the “P” (PARK) position. If
you move the selector lever to the “P” (PARK) position
before applying the parking brake, it may be difficult to
disengage the selector lever from the “P” (PARK) position
when next you drive the vehicle, requiring application of a
strong force to the selector lever to move from the “P”
(PARK) position.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-10 Driving safety
4

Curb weight: the weight of a motor vehicle with standard
equipment including the maximum capacity of oil, and
coolant.

Accessory weight: the combined weight (in excess of
those standard items which may be replaced) of automatic
transmission, power steering, power brakes, power win-
dows, power seats, radio, and heater, to the extent that
these items are available as factory- installed equipment
(whether installed or not).

Vehicle capacity weight: the rated cargo and luggage load
plus 150 lbs (68 kg)* times the vehicle’s designated seat-
ing capacity.

Production options weight: the combined weight of those
installed regular production options weighing over 5 lbs
(2.3 kg) in excess of those standard items which they
replace, not previously considered in curb weight or
accessory weight, including heavy duty brakes, ride level-
ers, roof rack, heavy duty battery, and special trim.

Normal occupant weight: 150 lbs (68 kg)* times the num-
ber of specified occupants. (In your vehicle the number is
2)

Occupant distribution: distribution of occupants in a vehi-
cle as specified. (In your vehicle the distribution is 2 in
front seat)
Tire and loading information placard
N00630100370
The tire and loading information placard is located on the
driver’s door sill.
*: 150 lbs (68 kg) is the weight of one person as defined by
U.S.A. and Canadian regulations.
BK0140800US.book 10 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Driving safety
4-13
4 Cargo loads
N00629700510
Cargo load precautionsTo determine the cargo load capacity for your vehicle, subtract
the weight of all vehicle occupants from the vehicle capacity
weight. For added information, if needed, refer to “Steps for
Determining Correct Load Limit” on page 4-11.
DO NOT USE the Gross Vehicle Weight Rating and Gross
Axle Weight Rating numbers listed on the safety certification
label located on the driver’s side door pillar as the guide for
passengers and/or cargo weight.
WA R N I N G
!
To reduce the risk of serious injury or death, the
combined weights of the driver, passengers and
cargo and must never exceed the vehicle capacity
weight.
Exceeding the vehicle capacity weight will adversely
affect vehicle performance, including handling and
braking, and may cause an accident.
Do not load cargo or luggage higher than the top of
the seatback. Be sure that your cargo or luggage
cannot move when your vehicle is in motion.
Having either the rear view blocked, or your cargo
being thrown inside the cabin if you suddenly have
to brake can cause a serious accident or injury or
death.
Put cargo or luggage in the cargo area of your vehi-
cle. Try to spread the weight evenly.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

6-2 For emergencies
6If the vehicle breaks down
N00836300220
If your vehicle breaks down on the road, move to the shoulder
and turn on the hazard warning flashers. If there is no shoulder,
or the shoulder is not safe, drive in the right lane slowly, with
the hazard lights flashing, until you come to a safe stopping
place. Keep the flashers flashing.
If the ready indicator light goes out while driving, the brakes
and steering will continue to work, but without power assist, so
more effort will be required for braking and steering. Stop the
vehicle on the shoulder of the road and turn on the hazard
warning flashers.
Jump-starting
N00836400739
If the electric motor unit cannot be energized because the 12V
starter battery is weak or dead, you can start it with the battery
from another vehicle using jumper cables. NOTE
Do not use jumper cables if they have damage or corro-
sion.
1. Take off any metal jewelry such as watch bands or brace-
lets that might make an accidental electrical contact.
WA R N I N G
!
To reduce the risk of igniting flammable gas that
may be emitted from the 12V starter battery, care-
fully read this section before jump-starting the vehi-
cle.
Do not try to start the electric motor unit by pushing
or towing the vehicle. This can cause an accident
resulting in serious injury or death and can damage
the vehicle.
CAUTION
!
Do not attempt jump starting the 12V starter bat-
tery while the main drive lithium-ion battery is
being charged. Doing so could damage the vehicle or
charging equipment.
BK0140800US.book 2 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-3
6
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles are not
touching each other.
3. Set the parking brake firmly on your vehicle and move the
selector lever into the “P” (PARK) position.
4. Set the parking brake firmly on the other vehicle. Put the
automatic transaxle in “P” (PARK) or the manual
transaxle in “N” (Neutral).
5. Turn the ignition switch (the electric motor switch) on
each vehicle to the “LOCK” position.NOTE
Turn off all lights, heater, and other electrical loads. This
will help avoid sparks.6. Remove the battery cover, and then make sure your 12V
starter battery electrolyte is at the proper level. (Refer to
“Checking 12V starter battery electrolyte level” on page
7-14.)
7. Connect one end of one jumper cable to the positive
(+) terminal of the discharged battery (A), and then con-
nect the other end to the positive (+) terminal of the
booster battery (B).
CAUTION
!
Check the other vehicle. It must have a 12V battery.
If the other system is not 12V, both systems can be
damaged.
WA R N I N G
!
If the electrolyte fluid is not visible, or looks frozen,
DO NOT ATTEMPT JUMP STARTING!!
The battery might split open or explode if the tem-
perature is below the freezing point or if it is not
filled to the proper level.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-7
6
As your vehicle has anti-lock brakesIf you drive your vehicle with a low battery charge, after the
electric motor unit has been started by using jumper cables, it
can cause the anti-lock braking system warning light to illumi-
nate. This is only due to the low battery voltage. It is not a
problem with the brake system. If this happens, fully charge the
12V starter battery and ensure the charging system is operating
properly.
Tire repair kit
N00836600366
This vehicle is equipped with a tire repair kit which can be
used to repair a minor puncture in tread area caused by a nail,
screw or similar object. A spare tire is not provided with this
vehicle.
WA R N I N G
!
The tire repair kit may not permanently seal a punc-
tured tire.
Using the tire repair kit may damage the wheel
and/or the tire inflation pressure sensor for the tire.
The vehicle must promptly be inspected and
repaired by a certified i-MiEV dealer after using the
tire repair kit.
Use only the Mitsubishi genuine tire repair kit. Seal-
ant in other repair kits may not sufficiently seal the
tire puncture.
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-11
6
NOTE
Do not pull out an object, such as a nail or screw, that pen-
etrates the punctured tire.

Move the vehicle so that the tire valve is positioned away
from the point where the tire touches the ground. If the
valve is near the point where the tire touches the ground,
the sealant may not enter the tire easily.
1. Park the vehicle on a safe, flat and level place.
2. Set the parking brake firmly.
3. Move the selector lever to the “P” (PARK) position and
turn the electric motor switch to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning
sign, such as a warning triangle or flashing signal lamp, at
an adequate distance from the vehicle, and have all your
passengers leave the vehicle.
5. Take out the tire sealant bottle and the compressor.6. Shake the tire sealant bottle well.
NOTE
In cold conditions (when the ambient temperature is 32 °F
{0 °C} or lower), thickening of the tire sealant can make
the tire sealant hard to squeeze out of the bottle. Warm the
bottle between your hands inside the vehicle.
CAUTION
!
If the vehicle body is contaminated by the tire seal-
ant, wipe the tire sealant off immediately with a wet
cloth.
Immediately wash clothes contaminated with tire
sealant.
BK0140800US.book 11 ページ ２０１１年９月２９日　木曜日　午後３時２８分