battery MITSUBISHI iMiEV 2012 1.G Manual PDF

Features and controls
3-75
3
Electric motor unit warning light
N00573600029
This warning light will illuminate when there is a problem with
a high voltage component.
Refer to “Service precautions” on page 7-2.Power down warning light
N00573700020
If the warning light illuminates when the outside air tempera-
ture is very low, move the vehicle to a warmer location.
If the warning light illuminates after the vehicle has been
driven continuously uphill or when the outside air temperature
is very high, stop the vehicle in a safe place so the electric
motor unit and/or the main drive lithium-ion battery can cool
down. When they have cooled down, the warning light will go
off. If the warning light does not turn off, contact a certified i-
MiEV dealer.NOTE
When the power down warning light illuminates, avoid
rapid starts and aggressive acceleration.

Illumination of the power down warning light does not
indicate a malfunction.

If the power down warning light illuminates while the air
conditioning is used, the cooling or heating may stop
operating and only the fan will operate.
CAUTION
!
If this light illuminates while driving, immediately
park your vehicle in a safe place and contact a certi-
fied i-MiEV dealer.
If this warning light illuminates, the power pro-
vided by the electric motor will be reduced and the
vehicle will be only able to move at low speeds.
This warning light will illuminate;

When the energy level in the main drive lith-
ium-ion battery is near empty.

When temperature of the electric motor unit
or the main drive lithium-ion battery is too
high or too low.

When voltage of the main drive lithium-ion
battery becomes low.
If the energy level gauge shows 0 bar, the main
drive lithium-ion battery is near empty and must
be charged as soon as possible. Refer to “Charg-
ing” on page 1-15.
BK0140800US.book 75 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-76 Features and controls
3Combination headlights and dimmer switch
N00522500710
HeadlightsNOTE
Do not leave the headlights and other lights on for a long
period of time while the ready indicator is not illuminated.
A run down 12V starter battery could result.

When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same as when window glass mists up on a humid day, and
does not indicate a problem. When the light is switched
on, the heat will dry out the fog. However, if water col-
lects inside the light, have it checked by a certified
i-MiEV dealer.
Type 1Rotate the switch to operate the lights.
The combinations of switch operations and illuminated lights
differ in accordance with the following conditions.
Except for vehicles equipped with daytime running lights
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0140800US.book 76 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-89
3 Electric rear window defogger switch
N00523700399
The electric rear window defogger can be used when the ready
indicator is illuminated.
The indicator light (A) will come on when you press the elec-
tric rear window defogger switch. Electric current will flow
through the heating wires on the rear window to help clear
away moisture or frost.
After about 20 minutes of operation, the system will shut off
automatically.
To switch the defogger OFF before 20 minutes have passed,
press the switch again. The indicator light will go out and the
defogger will turn off.
If you need the defogger for more than 20 minutes, press the
switch again. This will add 20 more minutes.
NOTE
If your vehicle is equipped with heated mirrors, mist can
also be removed from the outside rearview mirrors when
the rear window defogger switch is pressed. (Refer to
“Heated mirror” on page 3-29.)
CAUTION
!
The rear window defogger is not designed to melt
snow. Remove any snow manually before using the
rear window defogger.
Use the rear window defogger only after the ready
indicator is illuminated. Be sure to turn the defogger
switch off immediately after the window is clear to
save on 12V starter battery power.
Do not place stickers, tape, or other items that are
attached with adhesive over the grid wires on the
rear window.
When cleaning the inside rear window, use a soft
cloth and wipe lightly over the grid wires.
BK0140800US.book 89 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-91
3 Bluetooth
® 2.0 interface
(if so equipped)
N00563900087
The Bluetooth
® 2.0 interface allows for making/receiving
hands-free calls in the vehicle using a Bluetooth
® compatible
cellular phone based on the wireless communication technol-
ogy commonly known as Bluetooth
®. It also allows the user to
play music, saved in a Bluetooth
® music player, from the vehi-
cle’s speakers.
The system is equipped with a voice recognition function,
which allows you to make hands-free calls by simple switch
operations and voice command operations using a defined
voice tree.
The Bluetooth
® 2.0 interface can be used when the electric
motor switch is in the “ON” or “ACC” position.
Before you can use the Bluetooth
® 2.0 interface, you must pair
the Bluetooth
® device and Bluetooth
® 2.0 interface. Refer to
“Connecting the Bluetooth
® 2.0 interface and Bluetooth
®
device” on page 3-98.
Bluetooth
® is a registered trademark of BLUETOOTH SIG,
INC.
NOTE
If the electric motor switch is left in the “ACC” position,
the accessory power will automatically turn off after a cer-
tain period of time and you will no longer be able to use
the Bluetooth
® 2.0 interface. The accessory power comes
on again if the electric motor switch is turned from the
“ACC” position. Refer to “ACC power auto-cutout func-
tion” on page 3-30.

The Bluetooth® 2.0 interface cannot be used if the
Bluetooth
® device has a dead battery or the device power
is turned off.

Hands-free calls will not be possible if your phone does
not have service available.

If you place the Bluetooth
® device in the luggage com-
partment, you may not be able to use the Bluetooth
® 2.0
interface.
WA R N I N G
!
Although the Bluetooth
® 2.0 interface allows you to
make hands-free calls, if you choose to use the cellu-
lar phone while driving, you must not allow yourself
to be distracted from the safe operation of your vehi-
cle. Anything, including cellular phone usage, that
distracts you from the safe operation of your vehicle
increases your risk of an accident.

Refer to and comply with all state and local laws in
your area regarding cellular phone usage while driv-
ing.
BK0140800US.book 91 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-93
3
Volume up buttonPress this button to increase the volume. Volume down buttonPress this button to decrease the volume.SPEECH button
Press this button to change to voice recognition mode.
While the system is in voice recognition mode, “Listen-
ing” will appear on the audio display.

If you press the button briefly while in voice recognition
mode, it will interrupt prompting and allow voice com-
mand input.
Pressing the button longer will deactivate the voice recog-
nition mode.

Pressing this button briefly during a call will enable voice
recognition and allow voice command input.PICK-UP button
Press this button when an incoming call is received to
answer the telephone.

When another call is received during a call, press this but-
ton to put the first caller on hold and talk to the new caller.
• In such circumstances, you can press the button briefly
to switch between callers. You will switch to the first
caller and the other caller will be put on hold.
• To establish a three-way call in such situations, press the
SPEECH button to enter voice recognition mode and
then say “Join calls.”
HANG-UP button
Press this button when an incoming call is received to
refuse the call.

Press this button during a call to end the current call.
When another call is on hold, you will switch to that call.

If this button is pressed in the voice recognition mode, the
voice recognition mode will be deactivated.NOTE
When you press the SPEECH button to enter voice recog-
nition mode with a cellular phone paired to the system,
current information on the cellular phone, such as
“remaining battery life,” “signal strength” or “roaming,”
will be displayed on the audio display.*
*: Some cellular phones will not send this information to
the Bluetooth
® 2.0 interface.

Call waiting and three-way calls can be used by the
Bluetooth
® 2.0 interface, only if it is possible to use those
services with your cellular phone.
BK0140800US.book 93 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-107
3
Mute function
N00565900010
At any time during a call, you can mute the vehicle micro-
phone.
Pressing the SPEECH button and then saying “Mute” during a
call will turn ON the mute function and mute the microphone.
Saying “Mute off” in the same way will turn off the mute func-
tion and cancel the mute on the microphone.Switching between hands-free mode and private mode
N00566600014
The Bluetooth
® 2.0 interface can switch between hands-free
mode (hands-free calls) and private mode (calls using cellular
phone).
If you press the SPEECH button and say “Transfer call” during
a hands-free call, you can stop the hands-free mode and talk in
private mode.
To return to hands-free mode, press the SPEECH button again
and say “Transfer call.”
Phonebook function
N00566000018
The Bluetooth
® 2.0 interface has 2 types of unique phonebooks
that are different from the phonebook stored in the cellular
phone. They are the vehicle phonebook and the mobile
phonebook.
These phonebooks are used to register telephone numbers and
make calls to desired numbers via voice recognition function.
NOTE
Disconnecting the battery cable will not delete informa-
tion registered in the phonebook.Vehicle phonebook
N00566100048
This phonebook is used when making calls with the voice rec-
ognition function.
Up to 32 names can be registered in the vehicle phonebook per
language.
Also, each entry has 4 locations associated with: home, work,
mobile and other. You can register one telephone number for
each location.
You can register a desired name as a name for any phonebook
entry registered in the vehicle phonebook.
Names and telephone numbers can be changed later on.
The vehicle phonebook can be used with all paired cellular
phones.
BK0140800US.book 107 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-123
3
Card holderCards can be slipped into the front (A) of the lid of the vanity
mirror.
12 V power outlet
N00525000602
CAUTION
!
Be sure to use a “plug-in” type accessory operating
at 12 V and 120 W or less.
Be aware that using electronic equipment with the
ready indicator off may run the 12 V starter battery
down.
When the 12 V power outlet is not in use, be sure to
close the 12 V power outlet cover. This will prevent
the 12 V power outlet from becoming dirty and pos-
sibly short-circuiting.
BK0140800US.book 123 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-2 Driving safety
4Economical driving
N00628500029
For economical driving, there are some technical requirements
that have to be met. In order to achieve longer life of the vehi-
cle and the most economical operation, we recommend you to
have the vehicle checked at regular intervals according to the
“WARRANTY AND MAINTENANCE MANUAL”.Starting and accelerationAvoid driving with the accelerator pedal fully depressed, such
as for unnecessarily sudden starts, acceleration and decelera-
tion. Smoothly depress the accelerator pedal.
Observe the speed limit and keep the speed as constant as pos-
sible while driving.IdlingParking for a long period with the ready indicator illuminated
will shorten the cruising range.SpeedAt higher the vehicle speed the more main drive lithium-ion
battery is consumed. Avoid driving at full speed. Even a slight
release of the accelerator pedal will save a significant amount
of main drive lithium-ion battery charge.Tire inflation pressureCheck the tire inflation pressures at regular intervals Low tire
inflation pressure increases road resistance. In addition, low
tire pressures adversely affect tire wear and driving stability.Cargo loadsDo not drive with unnecessary articles in the luggage compart-
ment.
Air conditioningToo much cooling/heating can affect the cruising range, so
maintain an appropriate temperature to extend the cruising
range.
BK0140800US.book 2 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Driving safety
4-7
4 Driving during cold weather
N00629400403

Check the 12V starter battery, including terminals and
cables. During extremely cold weather, the 12V starter
battery will not be as strong and its power level may drop.
Before driving the vehicle, check to see if the headlights
are as bright as normal. Charge or replace the 12V starter
battery if necessary. During extreme cold weather, it is
possible that a very low 12V starter battery could freeze.
Check the antifreeze.
If there is not enough coolant because of a leak, add high-
quality ethylene glycol antifreeze and water. Use Dia
Queen Super Long Life Coolant Premium or an equiva-
lent. The recommended blend is about 50 % water and 50
% anti-freeze. Use a higher concentration (not over 60 %)
when the outside temperature is -31 °F (-35 °C) or lower.
When the electric motor unit is working very hard (for
example, during mountain driving and/or when the out-
side temperature is high), use a 50 % concentration. This
blend will provide adequate protection from corrosion and
boiling.
WA R N I N G
!
The 12V starter battery gives off explosive hydrogen
gas. Any spark or flame can cause the 12V starter
battery to explode, which could cause serious injury
or death.
Always wear protective clothes and a face mask
when working with your 12V starter battery, or let a
skilled mechanic do it.
WA R N I N G
!
Never open the coolant reservoir cap while it is hot.
You could be seriously burned.
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分

4-10 Driving safety
4

Curb weight: the weight of a motor vehicle with standard
equipment including the maximum capacity of oil, and
coolant.

Accessory weight: the combined weight (in excess of
those standard items which may be replaced) of automatic
transmission, power steering, power brakes, power win-
dows, power seats, radio, and heater, to the extent that
these items are available as factory- installed equipment
(whether installed or not).

Vehicle capacity weight: the rated cargo and luggage load
plus 150 lbs (68 kg)* times the vehicle’s designated seat-
ing capacity.

Production options weight: the combined weight of those
installed regular production options weighing over 5 lbs
(2.3 kg) in excess of those standard items which they
replace, not previously considered in curb weight or
accessory weight, including heavy duty brakes, ride level-
ers, roof rack, heavy duty battery, and special trim.

Normal occupant weight: 150 lbs (68 kg)* times the num-
ber of specified occupants. (In your vehicle the number is
2)

Occupant distribution: distribution of occupants in a vehi-
cle as specified. (In your vehicle the distribution is 2 in
front seat)
Tire and loading information placard
N00630100370
The tire and loading information placard is located on the
driver’s door sill.
*: 150 lbs (68 kg) is the weight of one person as defined by
U.S.A. and Canadian regulations.
BK0140800US.book 10 ページ ２０１１年９月２９日　木曜日　午後３時２８分