heating MITSUBISHI iMiEV 2016 1.G User Guide

Economical driving 6-2 Driving safety
6
N00628500029
For economical driving,
there are some tech-
nical requirements that
have to be met. In
order to achieve longer life of the vehicle andthe most economical
operation, we recom-
mend you to have the vehicle checked at reg- ular intervals according to the “WARRANTYAND MAINTENANCE MANUAL”. Avoid driving with the
accelerator pedal fully
depressed, such as for unnecessarily sudden starts, accelerati
on and deceleration.
Smoothly depress the
accelerator pedal.
Observe the speed limit and keep the speed as constant as possi
ble while driving.
Parking for a long period with the ready indi- cator illuminated will shorten the cruisingrange. At higher the vehicle speed the more main drive lithium-ion battery
is consumed. Avoid
driving at full speed. Even a slight release of the accelerator pedal wi
ll save a significant
amount of main drive lithium-ion battery charge. Check the tire inflation pressures at regular intervals Low tire inflat
ion pressure increases
road resistance. In addi
tion, low tire pressures
adversely affect tire we
ar and driving stabil-
ity. Do not drive with unnecessary articles in the luggage compartment. Too much cooling/heating can affect the cruising range, so maintain an appropriatetemperature to exte
nd the cruising range.
N00628900010
Drunk driving is one of the most frequent causes of accidents.
Your driving ability ca
n be seriously impaired
even with blood alcohol levels far below thelegal minimum. If you
have been drinking,
don’t drive. Ride with a designated non- drinking driver, call a cab or a friend, or usepublic transportation. Drinking coffee or tak- ing a cold shower will not make you sober. Similarly, prescription and nonprescriptiondrugs affect your aler
tness, perception and
reaction time. Consul
t with your doctor or
pharmacist before dr
iving while under the
influence of any of
these medications.
N00628600017
The original equipmen
t floor mat provided
with your vehicle was
specifically designed
for your vehicle. Always properly position the floor mat and assure it does not interfere with operation of the pedals. Always use theretaining clip on the driver’s floorboard to secure the floor mat. When used, this clip will help prevent the floor mat from moving for-ward and possibly interfering with the opera- tion of the pedals. To prevent the floor mat
Economical driving Starting and acceleration Idling Speed
Tire inflation pressure Cargo loads Air conditioning Driving, alcohol and drugs
WA R N I N G NEVER DRINK AND DRIVE. Your perceptions ar
e less accurate, your
reflexes are slower and your judgment is impaired.
Floor mat
BK0220401US.book 2 ページ ２０１５年６月３日　水曜日　午前７時４２分

Braking
Driving safety 6-5
6
 Check the antifreeze. If there is not enough coolant because of aleak, add high-quality ethylene glycol antifreeze and water. Use Mitsubishi Motors Genuine Super Long Life CoolantPremium or an equivalent. The recom- mended blend is abou
t 50 % water and 50
% anti-freeze. Use a
higher concentration
(not over 60 %) when the outside temper- ature is -31 °F (-35 °C) or lower. When the electric motor unit is working veryhard (for example, during mountain driv- ing and/or when the outside temperature is high), use a 50 %
concentration. This
blend will provide
adequate protection
from corrosion and boiling.
N00629501531
All the parts of the brake system are criticalto safety. Have the vehicle serviced by a certi- fied i-MiEV dealer at regular intervalsaccording to the “WARRANTY AND MAINTENANCE MANUAL”. Check the brake system while driving at a low speed immediately
after starting, espe-
cially when the brakes are wet, to confirm they work normally. A film of water can be formed on the brakediscs and prevent normal braking after driv- ing in heavy rain or through large puddles, or after the vehicle is washed. If this occurs, drythe brakes out by driving slowly while lightly depressing the brake pedal. On snowy roads, ice can form on the braking system, making the brak
es less effective.
While driving in such conditions, pay closeattention to preceding
and following vehicles
and to the condition of the road surface. From time to time, lightly
depress the brake pedal
and check how effective the brakes are.
Put the selector lever to “B” (REGENERA- TIVE BRAKE MODE) or “ECO” (ECO MODE) position according to the grade ofthe slope and vehicle sp
eed. This will allow
effective use of the regenerative brake and prevent the service brake from overheating.If the brake pedal is continuously or fre- quently depressed on downhill roads, the ser- vice brake could overheat and the brake performance will be reduced.
WA R N I N G The 12V starter batter
y gives off explosive
hydrogen gas. Any spark or flame cancause the 12V starter battery to explode,which could cause serious injury or death. Always wear protecti
ve clothes and a face
mask when working wi
th your 12V starter
battery, or let a skil
led mechanic do it.
WA R N I N GNever open the coolan
t reservoir cap while
it is hot. You could be seriously burned.
Braking When brakes are wet When driving in cold weather
When driving downhill
NOTE
 When the main drive lithium-ion battery level is full or nearly full, or the main drivelithium-ion battery temp
erature is too high or
too low, the regenerative braking force may be reduced. Refer to “Regenerative braking”on page 3-3.  If the red needle in the energy usage indica- tor does not move to the left of the neutral point (A) while the
accelerator pedal is
released, the regenerative brake will notwork. Refer to “Ener
gy usage indicator” on
page 5-37. In the such
case, before approach-
ing a long downhill
road, reduce speed to
prevent the service brake from overheating.
BK0220401US.book 5 ページ ２０１５年６月３日　水曜日　午前７時４２分

Air conditioning
Comfort controls 7-5
7
N00736500191
When the electric motor switch is in the “ON” position, select the blower speed by turning the blower speed selection dial.Turning the dial clockwise will increase the blower speed; turning the dial c
ounterclockwise will
decrease it. When the dial is set to the “OFF” When the dial is set to the “AUTO” position, the air flow is adjusted automatically accord- ing to the temperature of the interior and theposition of the temperature control dial.
N00736600235
Use this dial to adjust the temperature of the air flow from the vents. Turn the temperature control dial clockwiseto make the air warmer. Turn it counterclock- wise to make the air cooler. When the dial is set to middle (
) position,
only uncooled and unheated air will flow. When the dial is moved to middle (
) posi-
tion when using cooling or heating, cooling or heating stops.
N00736700210
To change the position and amount of air flowing from the vents, turn the mode selec-tion dial. Refer to “Changing the mode selec- tion” on page 7-2.
Blower speed selection dial
Temperature control dial
NOTE
 When the dial is moved from middle (
)
position to the left while the air conditioning is not operating, the ai
r temperature will not
change.
 When the dial is moved to middle (
) posi-
tion and then to the left while the air condi-tioning is operating,
the air conditioning
system is operating again.  When the temperature control dial is set to “C” position, the air se
lection will be auto-
matically set to the re
circulation position and
the air conditioning will operate.When the dial is moved thereafter, the air conditioning continues to
operate and the air
selection setting returns to the setting beforethe dial was set to “C” position.
Mode selection dial
NOTE
BK0220401US.book 5 ページ ２０１５年６月３日　水曜日　午前７時４２分

Air conditioning
Comfort controls 7-7
7
N00731000465
Push the switch, and the air conditioning compressor will turn on. The air conditioning indicator light (A) will come on. Push the switch again and the air condition- ing compressor will stop and the indicatorlight (A) goes off.
N00766500015
When the blower speed selection dial is notOFF and the MAX switch is pressed, the indi- cator light (A) illumina
tes and cooling/heat-
ing performance and
the air conditioning
setting is changed according to the tempera- ture control dial position. When the switch is pr
essed again, the opera-
tion returns to the mode before pressing the switch.
The heating capability is at maximum. The air flow is at maximum. The air conditioning au
tomatically operates
and the cooling capabi
lity is at maximum.
N00731101290
1. Set the mode selection dial to the “ ” 2. Set the air selection switch (A) to the out- side position.3. Turn the temperature control dial clock- wise or counterclockw
ise to the desired
temperature between middle (
) and “H”
position. 4. Select the desi
red blower speed.
Air conditioning switch MAX switch
When the temperature control dial is set between middle ( When the temperature control dial is in middle (
) position
When the temperature control dial is set between

Tire repair kit 8-10 For emergencies
8
If there is a gap between the tire and wheel because the tire has moved inwardfrom the wheel rim, press the tire tread towards the wheel to close the gap before running the compressor. (With no gaps,the tire pressure will rise.) pull the power cord plug out of the 12 V power outlet.
17. Affix the speed restriction sticker (R) to
the three-diamond mark on the steering wheel.
18. When you have inflated the tire to the
specified pressure, stow the compressor,bottle, and other items
in the vehicle and
make sure that the seat cushion is properly secured. (Refer to “Tire repair kit storage” vehicle so that the tire sealant can spread evenly in the tire. Drive with great care.Do not exceed a speed of 50 mph (80 km/h). Observe local speed limits.
19. After driving for 10 minutes or 3 miles (5
km), park the vehi
cle in safe place.
Remove the air compressor from the stowed position. Check the tire pressure using the air pressure gauge on the com-pressor. If the tire pressure has apparently not dropped, the emergency repair proce- dure is complete. Continue the processfrom step 21. If the tire pressure is
not sufficient, inflate
the tire to the specified pressure again anddrive the vehicle carefully without exceeding a speed of 50 mph (80 km/h).
CAUTION The surface of the compressor will get hot while the compressor is running. Do not keep the compressor running continuously for more than 10 minutes. After using thecompressor, wait for the compressor to cool before using it again. If the compressor becomes sluggish or hot while operating, it is
overheating. Immedi-
ately place the switch in the OFF positionand let the compressor cool down for at least 30 minutes.NOTE
 If the tire pressure does not rise to the speci- fied level within 10 mi
nutes, the tire may be
so severely damaged that the tire sealant can- not be used to effect the emergency repair. Do not drive the vehicl
e. Please contact a
certified i-MiEV dealer.
NOTE
 At this point the punctu
re hole is
not sealed
yet. Air will leak through the puncture holeuntil the emergency repa
ir procedure is com-
pleted (through step 19 or step 20 of these instructions).CAUTION Do not affix the sticke
r anywhere except the
specified position on th
e pad of the steering
wheel. Affixing the sticker in an incorrect position could prevent the SRS airbag fromdeploying properly.
CAUTION If you sense any abnorma
lity while driving,
stop the vehicle and c
ontact a certified i-
MiEV dealer. Otherwise the tire pressure may drop before the emergency repair proce- dure is completed,
rendering the vehicle
unsafe to drive.
BK0220401US.book 10 ページ ２０１５年６月３日　水曜日　午前７時４２分

For cold and snowy weather 9-18 Vehicle care and maintenance
9
stop rust and wear. Us
e Multipurpose Grease
NLGI Grade 2 sparingly for all sliding partsof the hood latch and release lever. Work the grease into the hood lock mechanism until all the movable surfaces are covered.Also, put a light coat
of the same grease on
the safety catch wherever moving parts touch.
N00942600131
The ventilation slots in
front of the wind-
shield should be brushed clear after a heavysnowfall so that the operation of the heating and ventilation
systems will not be impaired.
To prevent freezing of the weatherstripping on the doors, hood, etc., they should be treated with silicone grease.
It is a good idea to carry a shovel or a short- handled spade in the vehicle during the win- ter so that you can clear away snow if you get stranded. A small hand-brush for sweepingsnow off the vehicle a
nd a plastic scraper for
the windshield, side a
nd rear window are also
useful.
N00942700321
The fusible links will melt to prevent a fire ifa large current attempts to flow through cer- tain electrical systems. In case of a melted fusi
ble link, see a certified
i-MiEV dealer for in
spection and replace-
ment. For the fusible links, please refer to “Fuseload capacities” on page 9-19.
N00942800885 N00901000107
To prevent damage to the electrical system from short-circuiting
or overloading, each
individual circui
t is equipped with a fuse.
The fuse blocks are lo
cated in the passenger
compartment and in under the hood. The fuse block in the
passenger compartment
is located in front of the driver’s seat at theposition shown in the illustration. Press the tab (A) and remove the fuse cover (B).
For cold and snowy weather Ventilation slots Weatherstripping
Additional equipment (For regions where snow is encoun-tered) Fusible links
WA R N I N G Fusible links must not be replaced by any other device. Failing to fit the correct fus- ible link may result in fire in the vehicle, property destruction and serious or fatalinjuries at any time.
Fuses Fuse block location
NOTE
 Spare fuses are not provided. Please pur- chase from a certified i-MiEV dealer.
Passenger compartment
BK0220401US.book 18 ページ ２０１５年６月３日　水曜日　午前７時４２分