ignition MITSUBISHI iMiEV 2017 1.G Owners Manual

Electronic immobilizer (Anti-theft starting system)
5
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle
and any remaining keys
to a certified i-MiEV
dealer.
N00562200113
You can program new keys to the system ifyou have two valid (alr
eady registered) keys
and blank (not regist
ered) immobilizer key
(specially cut for your ve
hicle at a certified i-
MiEV dealer) by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the “ON” positionfor 5 seconds. 2. Turn the ignition to the “LOCK” position and remove the first key.3. Within 30 seconds of turning the first key to the “LOCK” position, insert the second valid key into the ignition and turn it tothe “ON” position. About 10 seconds later, the immobilizer indicator will start blinking.
4. When the immobilizer indicator starts blinking, turn the second valid key to the“LOCK” position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition and turnit to the “ON” position. Perform this oper- ation no more than 30 seconds after the immobilizer indicato
r starts blinking.
When registration of the ID code is com- plete, the immobilizer indicator will come on for 3 seconds then go off. If an error occurs, the immobilizer indicator will go off during the procedure. 5. If you wish to register another key, per- form the process again from step 1.
N00562300084
Your electronic imm
obilizer operates on a
radio frequency subject
to Federal Communi-
cations Commission (FCC) Rules (For vehi- cles sold in U.S.A.) and Industry CanadaRules (For vehicles so
ld in Canada). This
device complies with
Part 15 of the FCC
Rules and RSS-Gen of the Industry Canada
NOTE
 You are provided with
2 keys, but you may
add up to 6 more keys.
Customer key programming (Except for vehicles sold in Canada)
NOTE
 It is not possible to register a key if: • the immobilizer indi
cator goes off during
the procedure
• the immobilizer indica
tor does not come on
for 3 seconds after turning the ignition tothe “ON” position with
a blank immobilizer
key
 The procedure will be terminated automati- cally if: • a period of 30 seconds or longer elapses from the moment when the first key is turned to the “LOCK” position to the moment when the second key is turned tothe “ON” position • a period of 30 seconds or longer elapses from the moment when the second key is turned to the “LOCK” position to the moment when the blank immobilizer key(specially cut for your
vehicle at a certified
i-MiEV dealer) is turned to the

If the vehicle breaks down 8-2 For emergencies
8
N00836301243
If your vehicle breaks down on the road, move to the shoulder and turn on the hazard warning flashers. If there is no shoulder, orthe shoulder is not safe, drive in the right lane slowly, with the hazard lights flashing, until you come to a safe stopping place. Keep theflashers flashing. If the ready indicator light goes out while driving, the brakes a
nd steering will continue
to work, but without power assist, so more effort will be required
for braking and steer-
ing. Stop the vehicle on the shoulder of the road and turn on the hazard warning flashers. If you need to push your vehicle, turn theelectric motor switch to the “ON” position, and place the selector lever in the “N” (NEU- TRAL) position.
N00836400742
If the electric motor unit cannot be energizedbecause the 12V starter battery is weak ordead, you can start it with the battery from another vehicle using jumper cables.
1. Take off any metal jewelry such as watch bands or bracelets
that might make an
accidental electrical contact. 2. Position the vehi
cles close enough
together so that the jumper cables can reach, but be sure the vehicles are nottouching each other.
3. Set the parking brake firmly on your vehi- cle and move the selector lever into the “P” (PARK) position. 4. Set the parking brake firmly on the othervehicle. Put the automatic transaxle in “P”5. Turn the ignition switch (the electric motor switch) on each vehicle to the “LOCK” position. 6. Remove the battery
cover, and then make
sure your 12V starter
battery electrolyte is
at the proper level. (Refer to “Checking 12V starter battery electrolyte level” onpage 9-8.)
If the vehicle breaks down Jump-starting
WA R N I N G To reduce the risk of igniting flammable gas that may be em
itted from the 12V
starter battery, carefully read this sectionbefore jump-starting the vehicle. Do not try to start the electric motor unit by pushing or towing the vehicle. This can cause an accident re
sulting in serious
injury or death and
can damage the vehi-
cle.CAUTION Do not attempt jump st
arting the 12V starter
battery while the main
drive lithium-ion bat-
tery is being charged. Doing so could dam-age the vehicle or charging equipment.NOTE
 Do not use jumper cables if they have dam- age or corrosion.
CAUTION Check the other vehicle.
It must have a 12V
battery. If the other system is not 12V, bothsystems can be damaged.NOTE
 Turn off all lights, heat
er, and othe
r electrical
loads. This will
help avoid sparks.
BK0220401US.book 2 ページ ２０１５年６月３日　水曜日　午前７時４２分