turn signal bulb MITSUBISHI L200 2014 Owner's Manual (in English)

Indication lampsE00501600012Turn-signal indication lamps/
Hazard warning indication
lamps E00501700185
These indication lamps blink on and off
when a turn-signal lamp is operating.
NOTE l If the blinking is too fast, the
cause may be a blown lamp bulb
or a faulty turn-signal connection.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash
on and off continuously.High-beam indication lamp E00501800115
This indication lamp illuminates when
the high-beam is used.Front fog lamp indication
lamp* E00501900347
This indication lamp illuminates while
the front fog lamps are on.Rear fog lamp indication lamp E00502000114
This indication lamp illuminates while
the rear fog lamp is on.Diesel preheat indication lamp E00502300250
This indication lamp illuminates when
the ignition switch is placed in the “ON”
position. As the glow plug becomes hot,
the lamp goes out and the engine can be
started.CAUTIONl If the diesel preheat indication
lamp comes on after the engine
is started, the engine speed may
not rise above the idling speed
because of fuel freezing. In this
case, keep the engine idling for
about ten minutes, then turn
off the ignition switch and im-
mediately turn it on again to
confirm that the diesel preheat
indication lamp is off.
NOTE
l If the engine is cold, the diesel pre-
heat indication lamp is on for a lon-
ger time.
l When the engine has not been star-
ted within about 5 seconds after
the diesel preheat indication lamp
went out, return the ignition
switch to the “LOCK” position.
Then, turn the switch to the “ON”
position to preheat the engine
again.
l When the engine is warm, the die-
sel preheat indication lamp does
not come on even if the ignition
switch is placed in the “ON” posi-
tion.Fuel filter indication lamp E00509900170
This indication lamp illuminates when
the ignition switch is turned to the “ON”
position and goes off after the engine
has started. If it lights up while the en-
gine is running, it indicates that water
has accumulated inside the fuel filter; if
this happens, remove the water from the
fuel filter.
Refer to “Removal of water from the
fuel filter” on page 6-06.
When the lamp goes out, you can re-
sume driving. If it either does not go out
or comes on from time to time, we rec-
ommend you to have the vehicle inspec-
ted.
Instruments and controls
3-07
OKTE14E2
3

Switch position 4-Driver + Full luggage load-
ing
{ Vehicles without heavy du-
ty suspension}
Double cab
Vehicle condi- tionSwitch position“0”“2” or “3” or“4”●:1 person:Full luggage loadingSwitch position 0-Driver onlySwitch position 2-Driver + Full luggage load-
ing
{ Vehicles with heavy duty
suspension for Russia, Ka-
zakhstan and Ukraine}Switch position 3-Driver + Full luggage load-
ing
{ Vehicles with heavy duty
suspension except for Rus-
sia, Kazakhstan and Uk-
raine}
{ Vehicles with headlamp -
type 2* and without heavy
duty suspension}Switch position 4-Driver + Full luggage load-
ing
{ Vehicles with headlamp -
type 1* and without heavy
duty suspension}
*: Refer to “Outside” on page 8-24
Turn-signals lever E00506501273
The turn-signal lamps flash when the lever is oper-
ated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn-signal indication
lamps flash.
1- Turn-signals When making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected.
Instruments and controls
3-33
OKTE14E2
3

lIt is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point. •Flashing of the turn-signal lamps and the
indication lamp in the instrument cluster
when the lever is operated with the igni-
tion switch in the “ACC” position
• Flashing of the turn-signal lamps and the
indication lamp in the instrument cluster
three times when you move the lever to
(2) slightly then release it
• The time required to operate the lever for
the 3-flash function can be adjusted.Hazard warning flasher switch E00506600903
Use the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster.
NOTE
l If the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition.
l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out.
We recommend you to have the vehicle in-
spected.
Front fog lamp switch* E00506800934
The front fog lamps can be used only when the head-
lamps or tail lamps are on. Turn the knob once in
the “ON” direction to turn on the front fog lamps.
The indication lamp in the instrument cluster will
also come on. To turn the front fog lamps off, turn
the knob once in the “OFF” direction. While the
rear fog lamp is on, turn the knob twice in the
“OFF” direction to turn the front fog lamps off.
The knob will automatically return to its original po-
sition when you release it.
NOTE
l The front fog lamps are automatically turned
off when the headlamps or tail lamps are
turned off. To turn the front fog lamps on
again, turn the knob in the “ON” direction af-
ter turning on the headlamps or tail lamps.
l Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare may tem-
porarily blind oncoming vehicle drivers.
Instruments and controls
3-34 OKTE14E2
3

OutsideE01003302846
FrontType 1
1- Headlamps, high-beam: 60 W (HB3)
2- Headlamps, low beam: 55 W (H11)
3- Front turn-signal lamps: 21 W (PY21W)
4- Position lamps: 5 W (W5W)
5- Front fog lamps*: 55 W (H11)
6- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
7- Side turn-signal lamps (on outside rear-view
mirror)*
Type 21- Headlamps, high/low beam: 60/55 W (H4)
2- Position lamps: 5 W (W5W)
3- Front turn-signal lamps: 21 W (PY21W)
4- Front fog lamps*: 55 W (H11)
5- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
6- Side turn-signal lamps (on outside rear-view
mirror)*

Codes in parentheses indicate bulb types.
NOTE l The side turn-signal lamp (on outside rear-
view mirror) uses an LED instead of a bulb.
For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Service
Point.
RearType 1Type 21- High-mounted stop lamp: 5 W (W5W)
2- Rear turn-signal lamps: 16 W (W16W)
3- Tail and stop lamps: 21/5 W (P21/5W)
4- Reversing lamps: 16 W (W16W)
5- Rear fog lamp (Type 1, Driver’s side only):
21 W (P21W)
6- Rear fog lamp (Type 2, Driver’s side only):
21 W (W21W)
7- Licence plate lamps: 5 W (W5W)
Codes in parentheses indicate bulb types.Inside E01003401518
Single cab
1- Door courtesy lamps*: 3.4 W
2- Room lamp: 8 W
3- Glove box lamp: 1.4 W
4- Centre console downlight: 1.4 W
Maintenance
8-24 OKTE14E2
8

Position lampsE01003700833
Type 1 1.Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by pulling out.
2. To install the bulb, perform the removal
steps in reverse.
Type 2
1.Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by pulling out.
2. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps E01003800818
Type 1
1.Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by turning it anticlockwise while pressing
in.
2. To install the bulb, perform the removal
steps in reverse.
Type 2 1.Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the sock-
et by turning it anticlockwise while pressing
in.
Maintenance
8-27
OKTE14E2
8

2.To install the bulb, perform the removal
steps in reverse.Side turn-signal lamps (on fender)* E01003900633
1.To remove a side turn-signal lamp, insert a
straight blade (or minus) screwdriver at the
end of the lamp nearer the front of the body
and use it to gently lever the lamp out of the
body.
Front
NOTE
l Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.
2. Remove the socket and bulb assembly togeth-
er by turning it anticlockwise, and then re-
move the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
NOTE l When replacing the lamp assembly, push in
the end facing the rear of the vehicle first.
FrontSide turn-signal lamps (on outside rear-
view mirrors)* E01003900646
The side turn-signal lamp (on outside rear-view mir-
ror) uses an LED instead of a bulb. For repair and
replacement, contact a MITSUBISHI MOTORS Au-
thorized Service Point.Front fog lamps* E01004001537
1.Insert a straight blade (or minus) screwdriver
with a cloth over its tip at the edge of the cov-
er and pry gently to remove the cover.
Type 1Type 2
Maintenance
8-28 OKTE14E2
8

2.Remove the bulb (C) by turning it anticlock-
wise while pressing it inward.
3. To install the bulb, perform the removal
steps in reverse.
Type 2 (Driver’s side only) 1.Remove the socket and bulb assemblies by
turning it anticlockwise, and then remove the
bulb by pulling out.
2. To install the bulb, perform the removal
steps in reverse.
Rear combination lamps E01004200763
1. Open the rear gate.
(Refer to “Rear gate” on page 1-13.)
2. Remove the screws (A) that hold the lamp unit.
3.Move the lamp unit towards the rear of the ve-
hicle and remove the clips (B).
4. Remove each socket and bulb assembly by
turning it anticlockwise.C-Rear turn-signal lamp
Remove the bulb by pulling it out.D-Tail and stop lamp
Remove the bulb from the socket by turn-
ing it anticlockwise while pressing in.E-Reversing lamp
Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.
NOTE l When mounting the lamp unit, align the pins
(F) and clip (G) on the lamp unit with the
holes (H) in the body.
Maintenance
8-30 OKTE14E2
8

Switch 1-08
Electrical system 9-16
Electronic immobilizer (Anti-theft starting sys-
tem) 1-03
Emergency starting 6-02
Engine specifications 9-14
Engine
Coolant 8-06,9-21
Number 9-02
Oil 8-04,9-21
Overheating 6-04
Specifications 9-14
Used engine oils safety instructions and disposal in-
formation 05
Water temperature gauge 3-05 Error codes 5-43
Exterior and interior lamp operation 8-18
FFirst-aid kit and warning triangle band for secur-
ing 5-81
Floor console box 5-77
Fluid
Automatic transmission fluid

8-07,9-21
Brake fluid 8-08,9-21
Clutch fluid 8-09,9-21
Engine coolant 8-06,9-21
Power steering fluid 8-09,9-21
Washer fluid 8-08,9-21 For cold and snowy weather 8-19
Front console box 5-77
Front fog lamps
Bulb capacity 8-24
Indication lamp 3-07
Replacement 8-28
Switch 3-34 Front room lamp
Bulb capacity 8-25 Replacement 8-32
Front seat 2-03
Front turn-signal lamps
Bulb capacity

8-24
Replacement 8-27 Fuel consumption 9-19
Fuel
Filling the fuel tank 02
Fuel filter indication lamp 3-07
Fuel gauge 3-04
Fuel selection 02
Low fuel warning lamp 3-04
Modification/alterations to the electrical or fuel sys-
tems 04
Tank capacity 02 Fuses 8-20
Fusible links 8-19
G Gauges 3-02
General maintenance

8-18
General vehicle data 9-03
Genuine parts 05
Glove box 5-77
Glove box lamp
Bulb capacity 8-24
Replacement 8-33
H Handling of compact discs 5-49
Hazard warning flasher switch 3-34
Hazard warning indication lamps

3-07
Head restraints 2-08
Headlamp levelling switch 3-32
Headlamps
Bulb capacity 8-24
Headlamp flasher 3-31 Replacement 8-25
Switch 3-30
Washer switch 3-39
Heated mirror 4-10
Heated seats 2-06
Heater 5-03
High-mounted stop lamp
Bulb capacity

8-24
Replacement 8-31 Hinges and latches lubrication 8-19
Hooks
Coat hook 5-81
Convenient hook 5-81 Horn switch 3-40
I If the vehicle breaks down 6-02
Ignition switch 4-10
Indication and warning lamps

3-06
Indication lamps 3-07
Inside rear-view mirror 4-08
Inspection and maintenance following rough road
operation 4-36
Installation of accessories 04
Instruments 3-02
Interior lamps 5-74
J Jack handle 6-12
Storage 6-07 Jacking up the vehicle

6-13
Jack
Storage 6-07 Jump starting (Emergency starting) 6-02 Alphabetical index

2 OKTE14E2

K
Keyless entry system 1-04
Keys 1-02
LLabeling 9-02
Lamp monitor buzzer
3-31
Lamps (headlamps, fog lamp, etc.) auto-cutout
function 3-31
Leakage (Fuel, engine coolant, oil and exhaust
gas) 8-18
Licence plate lamps
Bulb capacity 8-24
Replacement 8-31 Limited-slip differential (LSD) 4-38
Link System 5-52
Low fuel warning lamp 3-04
Lubricants 9-21
LW/MW/FM electronic tuning radio with CD play-
er 5-13
MManual transmission 4-14
Oil 9-21 Manual window control 1-08
Mirror
Inside rear-view mirror 4-08
Outside rear-view mirrors 4-09
Vanity mirror 5-71 Modification/alterations

to the electrical or fuel sys-
tems 04
OOdometer 3-03 Oil
Differential oil
9-21
Engine oil 8-04,9-21
Manual transmission fluid 9-21
Transfer oil 9-21 Operation under adverse driving conditions 6-24
Other specifications 9-18
Outside rear-view mirrors 4-09
Overheating 6-04
P Parking 4-07
Parking brake 4-06
Parking brake lever stroke

8-16
Personal lamps 5-75
Replacement 8-32 Position lamps
Bulb capacity 8-24
Replacement 8-27 Power steering
Fluid 8-09,9-21
System 4-42 Precautions to observe when using wipers and
washers 3-39
Pregnant women restraint 2-12
Puncture (Tyre changing) 6-17
R Radio
LW/MW/FM electronic tuning radio with CD play-
er 5-13 Rear combination lamps
Bulb capacity

8-24
Replacement 8-30 Rear differential lock 4-30
Rear fog lamp
Bulb capacity 8-24 Indication lamp 3-07
Replacement

8-29
Switch 3-35 Rear room lamp 5-74
Bulb capacity 8-25
Replacement 8-32 Rear seat 2-07
Rear side/quarter window 1-12
Rear turn-signal lamps
Bulb capacity 8-24
Replacement 8-30 Rear window demister switch 3-39
Rear-view mirror
Inside 4-08
Outside 4-09 Refill capacities 9-21
Removal of water from the fuel filter 6-06
Replacement of lamp bulbs 8-23
Reversing lamps
Bulb capacity 8-24
Replacement 8-30 Room lamp 5-74,5-75
Running-in recommendations 4-04
S Safe driving techniques 4-03
Seat belt 2-09
Adjustable seat belt anchor

2-11
Child restraint 2-13
Inspection 2-26
Pregnant women restraint 2-12
Pretensioner 2-12
Seat belt reminder/warning lamp 2-11 Seat
Adjustment 2-03
Armrest (Double cab) 2-07
Front seat 2-03
Head restraints 2-08 Alphabetical index

3OKTE14E2

Heated seats 2-06
Rear seat 2-07
Secret box 5-78
Service precaution
8-02
Side airbag system 2-34
Side turn-signal lamps
Bulb capacity 8-24
Replacement 8-28 Snow tyres 8-14
Spare wheel 6-16
Spark plug 9-16
Specifications 9-02
Speedometer 3-03
Starting 4-12
Steering
Power steering fluid 8-09,9-21
Power steering system 4-42
Steering wheel height adjustment 4-08
Steering wheel lock 4-12
Steering wheel remote control switch 5-41 Stop lamps
Bulb capacity 8-23
Replacement 8-30 Storage spaces 5-76
Sun visors 5-70
Sunglasses holder 5-78
Sunroof 1-13
Safety mechanism 1-14
Sunshade 1-14
Switch 1-13 Super select 4WD 4-26
Supplemental restraint system 2-26
How the Supplemental Restraint System
works 2-28
Servicing 2-38
Warning lamp 2-37 TTachometer 3-03
Tail lamps
Bulb capacity

8-24
Replacement 8-30 Tank capacity 02
Ticket holder 5-70
Tools 6-09
Storage 6-07 Towing 6-20
Trailer towing 4-49
Transfer oil 9-21
Transmission
Automatic transmission Sports Mode 4A/T, 5A/
T 4-17
Fluid 8-07,9-21
Manual transmission 4-14
Specifications 9-15 Tripmeter 3-03
Turn-signal indication lamps 3-07
Turn-signals lever 3-33
Tyres 8-11
How to change a tyre 6-17
Inflation pressures 8-12
Rotation 8-13
Size (tyre and wheel) 9-17
Snow tyres 8-14
Tyre chains 8-14
Wheel condition 8-13
U USB input terminal 5-68
How to connect an iPod 5-68 USB input terminal
How to connect a USB memory device

5-68Used engine oils safety instructions and disposal
information 05
Utility box 5-78
V Vanity mirror 5-71
Vehicle care precautions

7-02
Vehicle dimensions 9-03
Vehicle identification number 9-02
Vehicle identification number plate 9-02
Vehicle information code plate 9-02
Vehicle labeling 9-02
Vehicle performance 9-09
Vehicle weight 9-10
Ventilators 5-02
W Warning lamps 3-08
Washer
Fluid 8-08,9-21
Switch 3-36,3-39 Washing 7-03
Water temperature gauge

3-05
Waxing 7-04
Weatherstripping 8-19
Weight 9-10
Wheel condition 8-13
Wheel
Specification 9-17 Wiper
Switch 3-36
Wiper blade rubber replacement 8-17
Wiper blades 8-17 Alphabetical index

4 OKTE14E2