change time MITSUBISHI L200 2018 (in English) Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2018, Model line: L200, Model: MITSUBISHI L200 2018Pages: 466, PDF Size: 28.42 MB
Page 298 of 466
The Bluetooth®
2.0 interface automatically
converts from text to voice the names regis- tered in the transferred phone book entries, and creates names.NOTEl Only the mobile phone book transferred
from the connected cellular phone can be
used with that cellular phone.
l You cannot change the names and telephone
numbers in the phone book entries registered
in the mobile phone book. You cannot select and delete specific phone book entries, ei- ther.
To change or delete any of the above, change the applicable information in the
source phone book of the cellular phone and then transfer the phone book again.
To import a devices phone book
Follow the steps below to transfer to the mo- bile phone book the phone book stored in the
cellular phone.
NOTEl Transfer should be completed while the ve-
hicle is parked. Before transferring, makesure that the vehicle is parked in a safe loca-
tion.
l The already stored phone book in the mobile
phone book is overwritten by the storedphone book in the cellular phone.NOTEl All or part of data may not be transferred,
even when the cellular phone supports Blue-
tooth ®
, depending on the compatibility of
the device.
l Only a home, a work, and a mobile number
can be imported.
l The maximum supported telephone number
length is 19 digits. Any telephone number of
20 digits or more will be truncated to the first 19 digits.
l If telephone numbers contain characters oth-
er than 0 to 9, *, # or +, these characters aredeleted before the transfer.
l For the connection settings on the cellular
phone side, refer to the instructions for the
cellular phone.
1. Press the SPEECH button.
2. Say “Phone book.”
3. The voice guide will say “Select one of
the following: new entry, edit number, edit name, list names, delete, erase all, or
import contact.” Say “Import contact.”
4. The voice guide will say “Would you
like to import a single entry or all con-
tacts?” Say “All contacts.”
5. The voice guide will say “Importing the
contact list from the mobile phone book. This may take several minutes to com-
plete. Would you like to continue?” An- swer “Yes,” transferring to the mobile
phone book the phone book stored in the cellular phone will start.
Answer “No,” to return to the main
menu.NOTEl The transfer may take some time to com-
plete depending on the number of contacts.
l If the Bluetooth ®
2.0 interface could not be
connected to the Bluetooth ®
compatible cel-
lular phone, the voice guide will say “Un- able to transfer contact list from phone” and
then the system will return to the main menu.
l If you press the
HANG-UP button or press
and hold the SPEECH button during the data
transfer, the transfer will be cancelled and
the system will return to the main menu.
l If an error occurs during the data transfer, all
transfer will be cancelled and the voice
guide will say “Unable to complete the phone book import” and then the system willreturn to the main menu.
l If there are no contacts in the phone book,
the voice guide will say “There are no con- tacts on the connected phone.”
6. When the transfer is complete, the voice
guide will say “Import complete” and then the system will return to the main
menu.
Bluetooth ®
2.0 interface*
7-94OKTE18E1For pleasant driving7
Page 305 of 466
CAUTIONlDo not touch the heating element or the cig-
arette lighter housing, hold the knob only to prevent burns.
l Do not allow children to operate or play with
the cigarette lighter as burns may occur.
l Something is wrong with the cigarette light-
er if it does not pop back out within approxi-
mately 30 seconds of being pushed in.
Pull it out and have the problem corrected at MITSUBISHI MOTORS Authorized Serv-
ice Point.
l Do not use any electric appliance that is not
approved by MITSUBISHI MOTORS . Do-
ing so could damage the socket. If you used
the cigarette lighter after damaging the sock- et, the cigarette lighter might pop out or fail
to come out after being pushed in.
l When the cigarette lighter socket is used as a
power source for an electric appliance, be sure that the electric appliance operates at
12 V and has an electric capacity of 120 W or less. In addition, long use of the electricappliance without running the engine may
run down the battery.Accessory socket
E00711602620
The accessory socket can be used while theignition switch or the operation mode is in
ON or ACC.
To use a plug-in type accessory, open the lid,
and insert the plug in the accessory socket.CAUTIONl Be sure to use a “plug-in” type accessory op-
erating at 12 V and at 120 W or less.
When using more than one socket at the same time, make sure that the electrical ac-
cessories are 12 V accessories and that the total power consumption does not exceed
120 W.
l Long use of the electric appliance without
running the engine may run down the bat- tery.
l When the accessory socket is not in use, be
sure to close the lid, because the socketmight become clogged by foreign materialand be short-circuited.Digital clock*
E00711801540
The digital clock indicates the time with the
ignition switch or the operation mode is in
ON or ACC.
To set the time
Set the time by pressing the various buttons
as described below.
1- To adjust the hour
2- To adjust the minutes
3- To reset the minutes to zero
10:30 - 11:29...... Changes to 11:00
11:30 - 12:29...... Changes to 12:00
Accessory socket
7-101OKTE18E1For pleasant driving7
Page 320 of 466
2.After setting the ignition switch or the
operation mode to “ON”, perform Steps
3 and 4 within 10 seconds.
3. Release your finger from the SOS
switch.
4. Press the SOS switch 3 or more times.
5. After approximately 10 seconds from
Step 2, the red lamp and the green lamp extinguish. After that, the buzzer sounds
3 times.NOTEl If the buzzer does not sound, repeat the
process from Step 1.
6. Approximately 60 seconds later, the
green lamp blinks. If you press the SOS switch within 20 seconds, the mode
changes to the test mode.
NOTEl When the red lamp blinks instead of the
green lamp, move the vehicle in a safe place, with good visibility, where radio waves can
be transmitted and received, then repeat the process from Step 1.
7. Within approximately 20 seconds after
the mode has changed to the test mode,
press the SOS switch for one of the fol-
lowing periods to select the desired test
type.
l 10 seconds or more: Report test to the
emergency call centre
l Less than 10 seconds: Test of the
ERA-GLONASS system equipment of
the vehicleNOTEl If you do not press the SOS switch within
approximately 20 seconds, the test modeends.
l If you drive a certain distance in the test
mode, the test mode ends.
Report test to the emergency
call centre
1. The green lamp illuminates, and the re-
port test to the emergency call centre is
started.
NOTEl If the red lamp illuminates for approximately
60 seconds, the vehicle is in a place where radio waves cannot be transmitted and re-ceived. Therefore you cannot report to the emergency call centre.
2. When the green lamp extinguishes, the
test mode is completed.
Test of the ERA-GLONASS
system equipment of the vehicle
1. After the buzzer sounds once, press the
SOS switch.
[Lamp Check]
When the buzzer sounds once and both the red and green lamp illuminate alter-nately, they are working normally.
2. When the lamps are normal, press the
SOS switch. When the lamps do not illu-
minate normally, wait for approximately
20 seconds.
[Speaker Check]
When the buzzer sounds twice and con-
tinues sounding, they are working nor-
mally.
3. When the speakers are normal, press the
SOS switch. When the buzzer does not
sound normally, wait for approximately
20 seconds.
[Microphone Check]
After the buzzer sounds 3 times, say something towards the microphone.If your voice sounds from the speakers,
they are working normally.
4. When the microphone is normal, press
the SOS switch. When it does not oper-
ate normally, wait for approximately 20
seconds.
5. If all check results are normal, the green
lamp illuminates (for approximately 5
seconds) and the buzzer sounds once.ERA-GLONASS*
8-06OKTE18E1For emergencies8
Page 321 of 466
WARNINGlIf any of the check results are not normal,
the red lamp illuminates (for approxi- mately 5 seconds) and the buzzer sounds 3times. In this case, there is a possible fail-
ure in the system. Have the system inspec- ted by a MITSUBISHI MOTORS Au-
thorized Service Point immediately.
6. When the green lamp extinguishes, the
test mode is completed.
If the vehicle breaks down
E00800101137
If the vehicle breaks down on the road, moveit to the shoulder and use the hazard warning
flashers and/or the warning triangle etc.
Refer to “Hazard warning flasher switch” on page 5-21.
If the engine stops/fails
Vehicle operation and control are affected if
the engine stops. Before moving the vehicle to a safe area, be aware of the following:
l The brake booster becomes inoperative
and the pedal effort will increase. Press
down the brake pedal harder than usual.
l Since the power steering system is no
longer operative, the steering wheel feels heavy when turning it.
If the operation mode
cannot be changed to OFF (vehicles equipped with the
keyless operation system) E00804900077
If the operation mode cannot be changed to OFF, perform the following procedure. 1. Move the selector lever to the “P”
(PARK) position, and then change the operation mode to OFF. (For vehicles with A/T)
2. One of the other causes could be low
battery voltage. If this occurs, the key-
less entry system, keyless operation
function and steering lock will also not operate. Contact a MITSUBISHI
MOTORS Authorized Service Point.Emergency starting
E00800504132
If the engine cannot be started because thebattery is weak or dead, the battery from an-other vehicle can be used with jumper cables to start the engine.
WARNINGl To start the engine using jumper cables
connected from another vehicle, perform
the correct procedures according to the instruction below. Incorrect procedures could result in a fire or explosion or dam-
age to the vehicles.
l Keep sparks, cigarettes and flames away
from the battery because the battery may produce an explosion.CAUTIONl Do not attempt to start the engine by pulling
or pushing the vehicle.
It could damage your vehicle.
l Check the other vehicle. It must have a 12-
volt battery.
If the other system isn’t 12-volt, shorting can
damage both vehicles.
l Use the proper cables suitable for the battery
size to prevent overheating of the cables.
l Check the jumper cables for damage and
corrosion before use.
l Always wear protective eye goggles when
working near the battery.
l Keep the battery out of the reach of children.
1.
Get the vehicles close enough so the
jumper cables can reach, but be sure the vehicles aren’t touching each other.
2. Turn off all lamps, heater and other elec-
trical loads.
If the vehicle breaks down
8-07OKTE18E1For emergencies8
Page 331 of 466
How to change a tyreE00801204051
Before changing a tyre, first stop your vehi- cle in a safe, flat location. 1. Park the vehicle on level and stable
ground, free of loose pebbles, etc.
2. Set the parking brake firmly.
3. On vehicles with manual transmission,
turn the ignition switch to the “LOCK”
position or put the operation mode in
OFF, and move the gearshift lever to the
“R” (Reverse) position.
On vehicles with automatic transmis- sion, move the selector lever to the “P” (PARK) position, and turn the ignitionswitch to the “LOCK” position or put
the operation mode in OFF.
4. Turn on the hazard warning flashers and
set up a warning triangle, flashing signal
lamp, etc., at an adequate distance from
the vehicle, and have all your passengers
leave the vehicle.
5. To prevent the vehicle from rolling
when jacking up the vehicle, placechocks or blocks (A) at the tyre that is
diagonally opposite from the tyre (B)
you are changing.WARNINGl Be sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.NOTEl The chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if needed.
l If chocks are not available, use stones or any
other objects that are large enough to hold the wheel in position.
6. Get the jack, jack handle and wheel nut
wrench ready.
Refer to “Tools, jack and jack handle” on page 8-11.
Spare wheel information
E00803601801
The spare wheel is stored under the floor of
the cargo bed.
Check the air pressure of the spare tyre fre-
quently and make sure it is ready for emer- gency use at any time.
Maintaining the spare wheel at the highest
specified air pressure will ensure that it can always be used under any conditions (city/ high-speed driving, varying load weight,
etc.).
CAUTIONl The pressure should be periodically checked
and maintained at the specified pressure while the tyre is stowed.
Driving with an insufficient tyre pressure
can lead to an accident. If you have no choice but to drive with an insufficient tyre
pressure, keep your speed down and inflate the tyre to the correct pressure as soon as
possible. (Refer to “Tyre inflation pressures”
on page 10-12.)To remove the spare wheel
E00803501594
1. Set the jack handle. (Club cab)
(Refer to “To use the jack handle (Clubcab)” on page 8-16.)
How to change a tyre
8-17OKTE18E1For emergencies8
Page 334 of 466
4.Insert the jack handle in the bracket of
the jack and hook the notch (E) on the
jack handle end to the claw (F) of the
bracket.
5. Move the jack handle up and down to
raise the ram until just before the jack
contacts the jacking point of the vehicle.
Ensure that the jack will properly con- tact the vehicle jacking point.
Move the jack handle up and down to raise the vehicle.NOTEl This jack is a 2 stage expansion type.WARNINGlStop jacking up the vehicle as soon as the
tyre is raised off the ground. It is danger-
ous to raise the vehicle any higher.WARNINGl Do not get under your vehicle while using
the jack.
l Do not bump the raised vehicle or leave it
sitting on the jack for a long time. Both
are very dangerous.
l Do not use a jack except the one that
came with your vehicle.
l The jack should not be used for any pur-
pose other than to change a tyre.
l No one should be in your vehicle when us-
ing the jack.
l Do not start or run the engine while your
vehicle is on the jack.
l Do not turn the raised wheel. The tyres
still on the ground could turn and make your vehicle fall off the jack.
6. Remove the wheel nuts with the wheel
nut wrench, then take the wheel off.
CAUTIONl Handle the wheel carefully when changing
the tyre, to avoid scratching the wheel sur- face.
7. Clean out any mud, etc. on the hub sur-
face (G), hub bolts (H) or in the installa- tion holes (I) in the wheel, and then
mount the spare wheel.
WARNINGl Mount the spare wheel with the valve
stem (J) facing outboard. If you cannot see the valve stem (J), you have installed the wheel backwards.
Operating the vehicle with the spare
wheel installed backwards can cause vehi-
cle damage and result in an accident.
How to change a tyre
8-20OKTE18E1For emergencies8
Page 402 of 466
C
Capacities........................................................ 11-17
Card holder........................................................ 7-99
Cargo loads........................................................6-83
Catalytic converter.......................................... 10-03
Cautions on handling of 4-wheel drive vehicles................................................... 6-52
CD player.................................................. 7-18,7-39
Central door locks............................................. 3-17
Centre console under tray................................7-105
Charge warning lamp........................................ 5-16
Check engine warning lamp.............................. 5-15
Child restraint.................................................... 4-11 Caution for installing the child re-straint on vehicles with a front
passenger airbag.................................. 4-11,4-26
Child restraint system with ISOFIX mountings.................................................... 4-21
i-Size child restraint system.......................... 4-15
Installing a child restraint system to the lower anchorage (ISOFIX
child restraint mountings) and
tether anchorage...........................................4-21
Suitability for various ISOFIX positions...... 4-14
Suitability for various seating positions........ 4-16
Child-protection rear doors............................... 3-20
Cigarette lighter............................................... 7-100
Cleaning Chrome parts................................................. 9-05
Exterior of your vehicle................................ 9-03
Genuine leather............................................. 9-03
Interior of your vehicle................................. 9-02
Plastic parts................................................... 9-04
Plastic, fabric and flocked parts.................... 9-02
Polishing....................................................... 9-04
Washing........................................................ 9-03
Waxing.......................................................... 9-04
Clock............................................................... 7-101
Clutch Fluid.................................................. 10-09,11-17
Coat hook........................................................ 7-108
Combination headlamps and dipper switch...... 5-17
Convenient hook............................................. 7-107
Coolant (engine)....................................10-06,11-17
Cruise control.................................................... 6-63 Indication lamp............................................. 6-64
Switch........................................................... 6-63
Cup holder....................................................... 7-106
D
Daytime running lamps..................................... 5-19Bulb capacity.............................................. 10-22
Replacement................................................ 10-27
Demister (rear window).................................... 5-27
Diesel particulate filter (DPF)........................... 6-22 Warning lamp................................................6-22
Diesel preheat indication lamp.......................... 5-14
Differential oil................................................. 11-17
Digital clock.................................................... 7-101 Time Setting......................................... 7-36,7-70
Dimensions...................................................... 11-04
Dipper (High/Low beam change)......................5-19
Display Indicator............................................... 7-35
Disposal information for used batteries............ 2-07
Doors Central door locks......................................... 3-17
Child-protection rear doors........................... 3-20
Dead Lock System........................................ 3-18 Door ajar warning lamp................................ 5-16
Locking and unlocking................................. 3-15
To open or close the rear door (Club cab).... 3-16
Driving, alcohol and drugs................................ 6-02
E
Easy select 4WD............................................... 6-352WD/4WD operation indication lamp.. 6-36,6-38
Low-range indication lamp........................... 6-38
Economical driving........................................... 6-02
Electric window control.................................... 3-21 Safety mechanism......................................... 3-23
Switch........................................................... 3-21
Timer function.............................................. 3-23
Electrical system............................................. 11-15
Electronic immobilizer (Anti-theft starting system)................................................ 3-03
Emergency key.................................................. 3-11
Emergency starting............................................8-07
Emergency stop signal system.......................... 6-56
Engine specifications.......................................11-14
Engine switch.................................................... 6-14
Engine
Check engine warning lamp..........................5-15
Coolant..............................................10-06,11-17 Diesel preheat indication lamp......................5-14Engine coolant temperature display.............. 5-06
Model.......................................................... 11-03
Number....................................................... 11-03
Oil..................................................... 10-05,11-17
Oil pressure warning lamp............................ 5-16
Overheating................................................... 8-09
Alphabetical index
12- 2 OKTE18E1Alphabetical index
Page 403 of 466
Safety and disposal information forused engine oil............................................. 2-06
Specifications.............................................. 11-14
Entering or leaving the vehicle..........................2-05
ERA-GLONASS............................................... 8-02
Exterior and interior lamp operation............... 10-16
F
First-aid kit and warning triangleband for securing........................................... 7-108
Floor console box............................................ 7-105
Fluid Automatic transmission fluid...................... 11-17
Brake fluid........................................ 10-08,11-17
Clutch fluid....................................... 10-09,11-17
Engine coolant.................................. 10-06,11-17
Power steering fluid.......................... 10-09,11-17
Washer fluid..................................... 10-08,11-17
Front fog lamps
Bulb capacity.............................................. 10-22
Indication lamp............................................. 5-13
Replacement................................................ 10-27
Switch........................................................... 5-22
Front room lamp.............................................. 7-102
Bulb capacity.............................................. 10-24
Replacement................................................ 10-30
Front seats......................................................... 4-02
Front turn-signal lamps Bulb capacity.............................................. 10-22
Indication lamp............................................. 5-13
Replacement................................................ 10-26
Switch........................................................... 5-21
Frozen road warning..........................................5-06
Fuel consumption............................................ 11-16
Fuel remaining warning display........................ 5-07
Fuel Bleeding the fuel system............................... 8-10Filling the fuel tank....................................... 2-03Fuel filter indication lamp............................. 5-14
Fuel remaining display.................................. 5-07
Fuel remaining warning display....................5-07
Fuel selection................................................ 2-02
Modification/alterations to the electrical or fuel systems............................. 2-06
Removal of water from the fuel filter........... 8-11
Tank capacity................................................ 2-03
Fuses................................................................ 10-17
Fusible links.................................................... 10-17
G
General maintenance....................................... 10-16
General vehicle data........................................ 11-04
Genuine parts.....................................................2-06
Glove box........................................................ 7-104
Glove box lamp Bulb capacity.............................................. 10-24
Replacement................................................ 10-31
H
Hazard warning flasher switch.......................... 5-21
Hazard warning indication lamps......................5-13
HDMI terminal.................................................. 7-98
Head restraints................................................... 4-05
Headlamp levelling switch................................ 5-19
Headlamp washer switch...................................5-26
Headlamps Auto-cutout function..................................... 5-18Bulb capacity.............................................. 10-22
Daytime running lamps................................. 5-19Dipper (High/Low beam change)................. 5-19
Headlamp flasher.......................................... 5-19
High-beam indication lamp...........................5-13
Lamp monitor buzzer.................................... 5-18
Replacement................................................ 10-24
Switch........................................................... 5-17
Heated mirror.................................................... 6-12
Switch........................................................... 5-27
Heated seats....................................................... 4-03
Heater........................................................ 7-04,7-09
High-mounted stop lamp Bulb capacity.............................................. 10-23
Hill start assist................................................... 6-54
Warning indicator......................................... 6-55
Hinges and latches lubrication........................ 10-16
Hooks Coat hook.................................................... 7-108Convenient hook......................................... 7-108
Horn switch....................................................... 5-28
I
If the operation mode cannot bechanged to OFF................................................8-07
If the vehicle breaks down................................ 8-07
Ignition switch................................................... 6-13
Indication and warning lamps........................... 5-12
Indication lamps........................................ 5-12,5-13
Inside rear-view mirror......................................6-08
Inspection and maintenance following rough road operation........................................ 6-51
Installation of accessories..................................2-05
Instruments........................................................ 5-02
Alphabetical index
12- 3
OKTE18E1Alphabetical index