wheel MITSUBISHI LANCER 2016 8.G Owner's Manual

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-21
5
If the
engine
will
not
start
because
the
bat-
tery
is
weak
or
dischar
ged,
refer
to
“Jump-starting
the
engine”
on
page
8-2
for instructions.A longer
warm
up
peri
od
wil
l only
con-
sume
extra
fuel.
The
engine
is warmed
up
enough
for
driving
when
the
bar
graph
of
the
engine
coolant
temperature
display
starts
to move.
Refer
to “Interrupt
display
screen
(W
ith
ignition
switch
in the
“ON”
position)” on page 5-101.
Your
vehicle
is equipped
with
an
electroni-
cally
controlled
fuel
injection
system.
This
is
a
system
that
automatically
controls
fuel
injection.
There
is
no
need
to
depress
the
accelerator pedal when starting the engine.The starte
r mo
tor sho
uld
not
be run
for
mo
re
than
15
seconds
at a time.
To prevent
battery
drain,
wait
a few
seconds
between attempts to restart the engine.1.Make
sure
all
occupants
are
properly
seated with seat belts fastened.2.Make sure the parking brake is applied.3.Press
and
hold
the
brake
pedal
down
firmly with your right foot.4.Press
and
hold
the
clutch
pedal
all
the
way
down
(manual
transaxle).
5.On
vehicles
with
manual
transaxle,
place
the
gearshift
lever
in
the
“N”
(Neutral)
position.On
vehicles
with
continuously
variable
transmission
(CVT)
make
sure
the
selec-
tor lever is in the “P” (P
ARK) position.
6.While
pushing
the
ignition
switch
from
“LOCK”
(PUSH
OFF)
to “LOCK”
(PUSH
ON),
set
the
ignition
switch
to the
“ON”
position
and
confirm
that
all
warn-
ing
lights
and
warning
displays
are
oper
-
ating properly
.
7.Without
pressing
the
accelerator
pedal,
slowly
turn
the
ignition
switch
to
the
“ST
ART”
position
to
start
the
engine.
Release
the
ignition
switch
when
the
engine
starts.
After
several
attempts,
you
may
experience
that the engine still does not start.
W
AR
NING
Never
run
the
engi
ne in a clos
ed or poorly
ventilate
d area
any
longer
than
is need
ed
to move your
veh
icle
out
of the
area. Car
-
bon
monoxide
gas,
which
is odorless
and
extr
emely
poisonous,
could
build
up
and
cause serious injury or death.CAUTIONDo not
push-star
t the vehicle.
Do
not
run
the
engine
at high
rpms
or drive
at high speeds
until
the
engin
e has had a
chance
to warm
up.
Releas
e the ignition
switch
as soon
as the
engi
ne starts. Otherwi
se, the starter motor
will be damag
ed.
Starting
the
engine

NOTE
For
models
equipped
with
a manual
trans-
axle,
the
starter
will
not
operate
unless
the
clutch
pedal
is fully
depressed
(Clutch
inter
-
lock). This is a safety feature.
NOTE
On
vehicles
with
CVT
, the
starter
will
not
ope
rate
unless
the selector
lev
er is in the “P”
(PARK)
or “
N” (NE
UTRAL
) position.
For s
afety
reasons, s
tart the engi
ne in the “P”
(PARK)
position
so
that
the wheels
are
locked.NOTE
Minor
noi
ses may
be heard
on
engi
ne start-
up.
These will disappear
as the engi
ne warms
up.
When the engine is hard to start

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-23
5
N00529301
264
To prevent
vehicle
theft,
only
the
emer
gency
key
with
the
pre-registered
F.A.S.T
.-key
inserted
can
start
the
engine.
(Electronic
immobilizer function)
The engin
e is off and
the stee
ring
wheel
is
locked.
The
eme
rgency
key
can
be
inserted
and
removed
only
when
the
ignition
switch
is
in this
position.
The
electrical
accessories
can
be
used
with
the engine o
ff.
The
engine
will
start
only
by
using
the
emer
-
gency
key
with
the
F.A.S.T
.-key
inserted.
It is
possible
to use
all
electrical
accessories
with
only the emer
gency key
.
Engages
the
starter
. Release
the
emer
gency
key
when
the
engine
starts.
The
ignition
switch
returns
automatically
to
the
“ON”
positi
on.
1.Remove
the
emer
gency
key
from
the
F.A.S.T.-key.
Refer to “Emer
gency key” on page 5-22.
2.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.3.Insert
the
emer
gency
key
into
the
ignition
switch, and slowly push and turn.
1-
Insert or remove the emer
gency key
2-
Lock
3-
Unlock
Ignition
switch

LOCK
ACCONSTART
NOTE
Your
veh
icle
is equipp
ed
with an electr
onic
immobilizer
. To start the eng
ine, the ID
code
which
the F.A.S.T
.-ke
y sends must match
the
one
registered to the immobilizer
computer
.
(Ref
er to “Electr
onic immobilizer
(Anti-
thef
t
starting
system)
” on page 5-27.)
To turn fr
om “LOCK” to “ACC”

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-24
Features and controls
5
1.[For vehicles with manual transaxle]Push
the
emer
gency
key
in at the
“ACC”
position
and
keep
it depressed
until
it is
turned
to
the
“LOCK”
position,
and
remove. [For
vehicles
with
continuously
variable
transmission (CVT)]First,
set
the
selector
lever
to
the
“P”
(PARK)
position,
and
then
slowly
turn
the
ignition
switch
to
the
“LOCK”
position
while
pressing
it.
2.Install the cover of the ignition switch.3.Reinsert
the
emer
gency
key
into
the
F.A.S.T.-key.
Steering wheel lock
NOTE
When
the
ignition
switch
cannot
be
turned
from
the “LOCK”
position
to the “ACC”
position,
turn
the ignition
switch
while
turn-
ing
the steer
ing
wheel
in bot
h directions.
To turn fr
om “ACC” to “LOCK”
NOTE
For
vehicles
with
CVT, the
emer
gency
key
cannot
be remove
d unless
the selector
lev
er
is set
to the “P” (PARK) position.
NOTE
Always
install
the
cover
of
the
ignition
switch
when
not
using
the
emer
gency
key
.
Not
doing
so could
cause
damage
if foreign
mater
ial
such
as dust gets into the keyhole
of
the
ignition
switch.
CAUTIONDo
not
turn
the ignition
switch
to the LOCK
position
while
the vehicle
is movi
ng.
This
will cause
the steer
ing
wheel
to lock, mak
ing
it impossible to operate the vehicle. If the
engine
is stopped
while
driving,
the
pow
er
brake
boos
ter
will
stop
functioning
and
greater
effort
for
braking
will
be
requi
red.
Also,
the powe
r steer
ing
system
will
not
function
and
it will
requi
re greater
effort
to manually steer
the vehicle.
Do
not
leav
e the ignition
switch
in the “ON”
position
for
a long
time
whe
n the engi
ne is
not
runni
ng.
The battery will run down.
Do
not
turn
the ignition
switch
to the
“START” position
whe
n the engi
ne is run-
ning.
It will damag
e the starter motor.

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-25
5
Turn
the
eme
rgency
key
to the
“LO
CK
” pos
i-
tion.Turn the steering wheel until it is locked.Turn
the
emer
gency
key
to
the
“ACC”
posi-
tion
while
moving
the
steering
wheel
slightly
.
Tips for starting
Do not
operate
the
starter
motor
continu-
ously
for
longer
than
15
seconds
as
this
could
run
the
battery
down
or damage
the
starter
motor
. If the
engine
does
not
start,
turn
the
eme
rgency
key
back
to
the
“LO
CK
” pos
ition,
wait a few
seconds
,
and
then
try
again.
Trying
repeatedly
with
the
engine
or
starter
motor
still
turning
will damage the starter mechanism.If the
engine
will
not
start
because
the
bat-
tery
is
weak
or
dischar
ged,
refer
to
“Jump-starting
the
engine”
on
page
8-2
for instructions.A longer
warm
up
period
will
only
con-
sume
extra
fuel.
The
engine
is warmed
up
enough
for
driving
when
the
bar
graph
of
the
engine
coolant
temperature
display
starts
to move.
Refer
to “Interrupt
display
screen
(W
ith
ignition
switch
in the
“ON”
position)” on page 5-101.
Starting the engineYour
vehicle
is equipped
with
an
electroni-
cally
controlled
fuel
injection
system.
This
is
a system
that
automatically
controls
the
fuel
injection.
There
is
no
need
to
depress
the
accelerator pedal when starting the engine.The starter
mo
tor sho
uld
not
be run
for
mo
re
than
15
seconds
at a time.
To prevent
battery
drain,
wait
a few
seconds
between attempts to restart the engine.1.Make
sure
all
occupants
are
properly
seated with seat belts fastened.2.Make sure the parking brake is applied.3.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.
To lock
To u
nlock
CAUTIONRemove
the emer
gency key whe
n leav
ing
the
vehicle.
If your
vehicle
needs
to be
towed,
turn
the
emer
gency
key to the
“ACC”
position
to
unlock the steering wheel.NOTE
If the
front
wheels
are
turned,
the
anti-theft
lock
may
sometimes
make
it difficult
to turn
the
emer
gency
key
from
“LO
CK” to “ACC”.
Firmly
turn
the steer
ing
wheel
to the left or
to the right
as you t
urn
the emer
gency ke
y.
Starting
W
AR
NING
Never
run
the engin
e in a clos
ed or poorly
ven
tilated
area
any lon
ger
than is need
ed
to move
you
r veh
icle
out of the area.
Car-
bon
monoxi
de gas,
which
is odorless
and
extr
emely
poi
sonous,
coul
d build
up
and
cause
serious
injur
y or
death.
CAUTIONDo not push-star
t the vehicle.
Do
not run
the engin
e at high
rpms
or drive
at high
speeds
until
the
engine
has
had
a
chance to
warm up.
Releas
e the
emer
gency
key
as soon
as the
engine
starts
. It
will
damage
the
starter
motor.
CAUTION

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-26
Features and controls
5
4.Insert
the
emer
gency
key
into
the
ignition
switch.5.Insert
the
F.A.S.T
.-key
into
the
emer
gency
key
.
6.Press
and
hold
the
brake
pedal
down
firmly with your right foot.7.Press
and
hold
the
clutch
pedal
all
the
way
down
(manual
transaxle).
8.On
vehicles
with
manual
transaxle,
place
the
gearshift
lever
in
the
“N”
(Neutral)
position. On
vehicles
with
CVT
, make
sure
the
selector
lever
is in
the
“P”
(PARK)
posi-
tion.
9.Turn
the
emer
gency
key
with
the
F.A.S.T
.-key
to
the
“ON”
position
and
make
certain
that
all
warning
lights
and
warning
displays
are
functioning
properly
before starting the engine.
10.
Turn
the
emer
gency
key
with
the
F.A.S.T.-key
to
the
“START”
pos
ition
without
pressing
the
accelerator
pedal.
Release
the
emer
gency
key
with
the
F.A.S.T
.-key when the engine starts.
11.Remove
the
F.A.S.T
.-key
from
the
emer
-
gency key
.
NOTE
For
models
equipped
with
a manual
trans
-
axle,
the
starter
will
not
operate
unless
the
clu
tch
pedal is fully
depre
ssed (Cl
utch
inter-
lock). This is a safety feature.
NOTE
On
vehicles
with
continuously
variable
trans
mission
(CV
T),
the
starter
will not
oper
-
ate
unless
the
selector
lever
is in
the
“P”
(PARK)
position
or
the
selector
lever
is in
the “N” (NE
UTRA
L) position
with
the brake
pedal depr
essed.
For s
afety
reas
ons, s
tart the eng
ine in t
he “P”
(PARK)
position
so
that
the
wheels
are
locked.NOTE
Minor
noi
ses may
be heard
on
engi
ne start-
up.
These will disappear
as the engi
ne warms
up.

Parking brake 5-48 Features and controls
5
N00511401439
To park the vehicle, first bring it to a com- plete stop and fully engage the parking brake.For vehicles with a manual transaxle, move the gear shift lever to 1st (on a uphill) or “R” (Reverse) (on a downhill) position.For vehicles with a continuously variable transmission (CVT), set the selector lever to “P” (PARK) position.
When parking on a hill, apply the parking brake and turn the front wheels toward thecurb on a downhill grade, away from the curb on an uphill grade.
 Be sure to close the sunroof completely when washing the vehicle or when leaving the vehicle.  Do not put any wax on the weatherstrip (black rubber) around the sunroof opening. If it is waxed, the weatherstrip cannot maintain a weatherproof seal with the sunroof.  After washing the vehicle or after rain be sure to wipe off any water that is on the sun-roof before operating it.  Operating the sunroof repeatedly with the engine turned off will run down the battery. Operate the sunroof only while the engine is running.
Parking brake
NOTE
To apply 1- Pull the lever up without pushing the
button at the end of hand grip. When the parking brake is set and theignition switch is in the “ON” position, the brake warning light in the instru- ment cluster will come on. Before driving, be sure to release the parking brake.
To r e l e a s e 1- Pull the lever up slightly. 2- Push and hold the button at the end of
the hand grip.
3- Push the lever downward.
BK0230300US.bo
ok 48 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Steering wheel tilt lock lever Features and controls 5-49
5
N00511500215
To adjust the steering wheel height, release the tilt lock lever while holding the steeringwheel by hand, and raise or lower the steering wheel to the desired height. After adjustment, securely lock the lever bypulling it upward.
CAUTION Before driving, be sure that the parking brake is fully released and brake warning light is off. If you drive without the parking brake fully released, the warning display will appear onthe information screen in the multi-informa- tion display. If a vehicle is driven without releasing theparking brake, the brakes will be overheated, resulting in ineffective braking and possible brake failure. Warning light Warning display type 1 Warning display type 2
Steering wheel tilt lock lever 1- Locked 2- ReleasedWA R N I N G After adjusting, make sure the lock lever is secured in the locked (1) position. Type 1 Type 2
 Do not attempt to adjust the steering wheel while driving. This can be danger- ous. When releasing the tilt lock lever {moving it to the position (2)}, be sure to hold the steering wheel firmly. Otherwise, the steering wheel may slip down too sud-denly. WA R N I N G
BK0230300US.bo
ok 49 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Ignition switch
Features and controls 5-53
5
The engine is off and the steering wheel is locked. The key can be inserted and removedonly when the switch is in this position. Allows operation of electrical accessories with the engine off. The engine runs and all accessories can be used.
Engages the starter. After the engine starts, release the key and it will return automati-cally to the “ON” position.
N00539601097
After about 30 minutes has elapsed with theignition switch in the “ACC” position, the function automatically cuts out the power for the audio system and other electric devicesthat can be operated with that position. When the ignition switch is turned from the “ACC” position, the power is supplied againto those devices.
N00550901237
For vehicles with a manual transaxle, whenremoving the key, push the key in at the“ACC” position and keep it depressed until it is turned to the “LOCK” position, and remove. For vehicles with a continuously variable transmission (CVT), when removing the key,first set the selector lever to the “P” (PARK)
LOCK ACC ON Manual transaxle
CVT
START
NOTE
 Your vehicle is equipped with an electronic immobilizer. To start the engine, the ID code which the transponder inside the key sendsmust match the one registered to the immobi- lizer computer. (Refer to “Electronic immobilizer” on page5-4.)
ACC power auto-cutout func- tion
NOTE
 It is possible to modify functions as follows:
• The time until the power cuts out can be changed to about 60 minutes. • The ACC power auto-cutout function can be deactivated. For details, consult a Mitsubishi Motors dealer.
To remove the key
NOTE
Manual transaxle
BK0230300US.bo
ok 53 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Steering wheel lock 5-54 Features and controls
5
position, and then turn the key to the “LOCK” position and remove it.
N00512500195
[For vehicles equipped with the F.A.S.T.-key]For information on operations for vehicles equipped with the F.A.S.T.-key, refer to “F.A.S.T.-key: Steering wheel lock” on page5-20. [Except for vehicles equipped with the F. A . S . T. - k e y ]
Remove the key at the “LOCK” position. Turn the steering wheel until it is locked. Turn the key to the “ACC” position while moving the steering wheel slightly.
NOTE
 For vehicles with a CVT, the key cannot be removed unless the selector lever is set to the“P” (PARK) position, wh
ich allows the igni-
tion switch to turn to the “LOCK” position.CAUTION Do not remove the ignition key from the ignition switch while driving. The steering wheel will lock, causing loss of control. If the engine is turned off while driving, the power brake booster will stop functioning and braking efficiency will be reduced. Also,the power steering system will not function and it will require greater effort to manually steer the vehicle.CVT
 Do not leave the key in the “ON” position for a long time when the engine is not running. This will cause the battery to run down. Do not turn the key to the “START” position when the engine is running. It will damage the starter motor.
Steering wheel lock
CAUTION
To l o c k To u n l o c k
CAUTION Remove the key when leaving the vehicle.NOTE
If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the key from “LOCK” position to “ACC” position. Firmly turn the steering wheel tothe left or to the right as you turn the key.
BK0230300US.bo
ok 54 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Starting and stopping the engine 5-56 Features and controls
5
7. Turn the ignition switch to the “ON” posi- tion and make certain that all warning lights are functioning properly beforestarting the engine.8. Turn the ignition switch to the “START” pedal. Release the key when the enginestarts.
After several attempts, you may experience that the engine still does not start. 1. Make sure that all electric devices, such as lights, air conditioning blower and rearwindow defogger, are turned off.
2. While depressing the brake pedal on vehi- cles equipped with continuously variable transmission (CVT) or the clutch pedal on the vehicles equipped with manual trans-axle, press the accelerator pedal halfway and hold it there, then crank the engine. Release the accelerator pedal, immedi-ately after the engine starts. 3. If the engine still will not start, the engine could be flooded with too much gasoline.While depressing the brake pedal on vehi-cles equipped with CVT or the clutch pedal on the vehicles
equipped with man-
ual transaxle, push the accelerator pedalall the way down and hold it there, then crank the engine for 5 to 6 seconds. Return the ignition switch to the “LOCK”position and release the accelerator pedal. Wait a few seconds, and then crank the engine again for 5 to 6 seconds whiledepressing the brake pedal or the clutch pedal, but do not push the accelerator pedal. Release the ignition key if theengine starts. If the engine fails to start, repeat these procedures. If the engine still will not start, contact your local Mitsubi-shi Motors dealer or a repair facility of your choice for assistance.
When the ambient temperature is -4 °F (-20 °C) or lower on vehicles with CVT, itmay not be possible to start from a standstill even with the selector lever in the “D” (DRIVE) or “R” (REVERSE) position.This phenomenon occurs because the trans-axle has not warmed up sufficiently; it does not indicate a problem. If it occurs, place the selector lever in the “P” (PARK) position andlet the engine idle for at least 10 minutes. The transaxle will warm up, and you will be able to start normally.Do not leave the vehicle during warm-up operation.
N00542301102
1. Bring the vehicle to a complete stop. 2. Fully engage the parking brake while depressing the brake pedal. 3. For vehicles with a manual transaxle, turn the ignition switch to the “LOCK” posi- tion to stop the engine, and then move thegearshift lever to the 1st (on a uphill) or “R” (Reverse) (on a downhill) position.
NOTE
 On vehicles with CVT, the starter will not operate unless the selector lever is in the “P” (PARK) or “N” (NEUTRAL) position. For safety reasons, start the engine in the “P” (PARK) position so that the wheels arelocked.NOTE
 Minor noises may be heard on engine start- up. These will disappear as the engine warms up.
When the engine is hard to start
Startability of continuously vari- able transmission (CVT) vehicles at extremely cold ambient temper- ature Stopping the engine
BK0230300US.bo
ok 56 ページ ２０１５年７月３０日　木曜日　午後８時３８分