door lock MITSUBISHI LANCER EVOLUTION 2007 Service User Guide

CIRCUIT DIAGRAMS
H1J11X12AA
B-170
CENTRAL DOOR LOCKING SYSTEM
L.H. drive vehicles

CIRCUIT DIAGRAMS
H1J11X15AA
B-172
CENTRAL DOOR LOCKING SYSTEM
R.H. drive vehicles

INDEX - In order of connector No.C-9
Wiring diagram
page Circuit diagram page Parts name Connector
No.
DD-27Fuel gauge unit (Sub)B-148,152,156B-31,33
D-28Seat belt pretensioner (LH)B-249,251B-31,33
D-29Floor wiring harness (RH) and fuel
wiring harness combinationB-93,101B-31,33
D-30Floor wiring harness (RH) and fuel
wiring harness combinationB-93,101,148,152,156,203,211,217,
225,233,243B-31,33
D-32G sensor (Longitudinal)B-200,208,213,221,229,239B-31,33
D-33G sensor (Lateral)B-200,208,213,221,229,239B-31,33
D-34Intercooler water spray switchB-257B-31,33
EE-02Remote controlled mirror (LH)B-192,193B-34,36
E-04Spare connector speaker (LH)>B-196B-34,36
E-05Power window motor (Front:LH)B-162,165B-34,36
E-07Power window main switchB-162,163,168,169B-34,36
E-08Door lock actuator (Front:LH)B-170,173B-34,36
E-10Power window motor (Rear:LH)B-161,167B-34,36
E-11Power window sub switch (Rear:LH)B-161,167B-34,36
E-12Door lock actuator (Rear:LH)B-171,173B-34,36
E-13Remote controlled mirror (RH)B-192,193B-34,36
E-16Door lock key cylinder switch (RH)B-170B-35
E-17Door lock key cylinder switch (LH)B-172B-37
E-18Door lock actuator (Front:RH)B-171,172B-35,37
E-19Power window sub switch (Passenger’s
side)B-159,165B-35,37
E-20Power window motor (Front:RH)B-159,168B-35,37
E-21Spare connector speaker (RH)>B-196B-35,37
E-23Door lock actuator (Rear:RH)B-171,173B-35,37
E-24Power window sub switch (Rear:RH)B-160,166B-35,37
E-25Power window motor (Rear:RH)B-160,166B-35,37
FF-01Spare connector (LH)>B-197B-38,39
F-04Luggage compartment lampB-119,123B-38,39
F-05High mounted stop lampB-144,145B-38,39
F-06Defogger ( - )B-185B-38,39

INDEX - In order of parts nameC-12
Wiring diagram
page Circuit diagram page Connector
No. Parts name
CColumn switchC-203B-104,107,112,116,125,128,137,141,
187,191B-22,28
Combination meterC-01B-84,87,95,103,106,118,122,126,129,
135,139,148,149,152,153,156,157,
198,206,214,222,230,240,248,250,
256, 258B-18,24
Combination meterC-02B-110,115,118,122,126,129,135,139,
148,149,152,153,156,157,198,206,
248, 250,256,258B-18,24
Condenser fan motorA-45B-177,183B-7,9
Condenser fan motorA-46B-177,183B-7,9
Condenser fan relay (HI)A-07XB-73,177,183B-6,8
Condenser fan relay (LO)A-06XB-73,177,183B-6,8
Control wiring harness and battery
wiring harness combinationB-14B-79,84,91,99,157B-10,14
Control wiring harness and floor wiring
harness (LH) combination
C-46B-224,244B-25
Crank angle sensorB-121B-88,96B-13,16
DDefogger (-)F-06B-185B-38,39
Defogger (+)F-19B-185B-38,39
Defogger relayC-214B-54,55,78,185B-23,29
Detonation sensorB-122B-89,97B-13,17
Diagnosis connectorC-22B-92,100,105,108,113,117,119,123,
125,128,137,141,150,154,158,164,
170,172,188,189,204,205,219,227,
237,247,248,250,252,254B-18,24
Diagnosis connectorC-23B-92,100B-18,24
Direction valve (LH) F-25B-235,245B-38,39
Direction valve (RH) F-26B-235,245B-38,39
Door lock actuator (Front:LH)E-08B-170,173B-34,36
Door lock actuator (Front:RH)E-18B-171,172B-35,37
Door lock actuator (Rear:LH)E-12B-171,173B-34,36
Door lock actuator (Rear:RH)E-23B-171,173B-35,37
Door lock key cylinder switch (LH)E-17B-172B-37
Door lock key cylinder switch (RH)E-16B-170B-35
Door switch (Front:LH)D-13B-105,112,120,121,158B-30,32
Door switch (Front:RH)D-01B-108,116,120,121,164B-30,32

GENERAL -Vehicle IdentificationGENERAL -Vehicle Identification00-16
CHASSIS NUMBER
The chassis number is stamped on the toeboard inside the
engine compartment.
1
234
5
67
8911
10
No.ItemsContents
1Fixed figureJAsia
2Distribution channelMJapan channel
3DestinationYFor Europe and General Export
4Body styleS4-door sedan
5Transmission typeN5-speed manual transmission
6Development orderCTMITSUBISHI LANCER EVOLUTION-VII
7Engine94G63: 1,997 mL petrol engine
8SortAPassenger car
9Model year22002
10PlantUMIZUSHIMA-1
11Serial number--
ENGINE MODEL NUMBER
1. The engine model number is stamped on the cylinder
block as shown below.
Engine modelEngine displacement mL
4G631,997
2. The engine serial number is stamped near the engine
model number.
Engine serial numberAA0201 to YY9999

MPI -Troubleshooting13A-110
Terminal No.Normal condition Check condition (Engine condition) Check item
12Power supplyIgnition switch: “ON”System voltage
25
19Air flow sensor reset
signal
Engine: Idle operation0-1V
signal
Engine speed: 3,000 r/min6-9V
21Fan controllerRadiator fan is not operating0 - 0.3 V
Radiator fan is operating0.7 V or more
22Fuel pump relay 2Ignition switch: “ON”System voltage
Engine: Idle operation1 V or less
24A/C load signalDEngine:
Idle operation
DA/C switch: ON
(A/C compressor
runs)DOutdoor air
sensor ambient
temperature:
18_C or more
DA/C setting
temperature:
Minimum
temperature
DA/C air volume:
Maximum1 V or less
DA/C setting
temperature:
indoor
temperature
DA/C air volume:
MinimumSystem voltage
32Condenser fan motor
relay (HI)Fan inactive state
(Engine coolant temperature: 90_C or less)System voltage
Fan high-speed rotation state
(Engine coolant temperature: 105_C or more)1 V or less
33Alternator G terminalDEngine: After warm-up, idle operation
DRadiator fan: Not operating
DHeadlamp: OFF→ON
DStop lamp: OFF→ON
DRear defogger switch: OFF→ONVoltage increases by
0.2 - 3.5 V
34Condenser fan motor
relay (LOW)Fan inactive state
(Engine coolant temperature: 90_C or less)System voltage
Fan low-speed rotation state (Engine coolant
temperature: 95 - 100_C or more)1 V or less
35Intercooler water
spraylamp
Ignition switch: “ON”System voltage
spraylamp
Ignition switch: “LOCK” (OFF)1 V or less
36Engine warning lampIgnition switch: “LOCK” (OFF)→“ON”1 V or less→System
voltage (After several se-
conds have elapsed)

BODY -Fuel Filler Door42-7
FUEL FILLER DOOR
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operations
DRear Seat Removal and Installation. (Refer to GROUP
52A.)
DFront Scuff Plate (Driver’s Side), Rear Scuff Plate(Driver’s Side), Center Pillar Lower Trim (Driver’s
Side), Quarter Trim (Driver’s Side) Removal and
Installation (Refer to GROUP 52A – Trim.)
5
1
3 4 3
2
5.0±1.0 N·m
Adjustment of clearance around
fuel filler door
Removal steps
1. Fuel filler door panel assembly
2. Clip
3. Fuel filler door hook assembly4. Fuel filler door lock release cable
5. Fuel filler door lock release handle

BODY -DoorsBODY -Doors42-20
Tool UseName Number
A
B
C
D
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: ProbeTerminal voltage measurement
A: Connector pin contact pressure check
B: Power circuit check
C: Power circuit check
D: Commercial tester connection
TROUBLESHOOTING
DIAGNOSIS FUNCTION
The power window and central door locking is controlled by the Smart Wiring System (SWS). For
troubleshooting, refer to GROUP 54B - Troubleshooting.
ON-VEHICLE SERVICE
DOOR ADJUSTMENT
1. If the gap between the door and body is inconsistent,
paste protection tape at the fender around the hinge
attached portion and at the door edge, use the special
tool to loosen the bolt fixing the door hinge at the body
side, and move the door to adjust so that the gap around
the door becomes consistent.
2. If steps exist between the door and body, use the special
tool to loosen the bolt fixing the door hinge at the door
side, and move the door and adjust the alignment of
the door surface.
Caution
Do not apply torque above 98 NSm for the special
tool (MB991164).
MB990900 or
MB991164

BODY -DoorsBODY -Doors42-36
"BALOWER SASH INSTALLATION
Be sure to install the lower sash to the window rear sash
(at door) securely.
"CADOOR INSIDE HANDLE INSTALLATION
1. Install the inside lock cable to the door inside handle
as follows:
(1) Install the inner cable end in the inside lock cable
to the clip in the door inside handle.
(2) Turn the inside lock knob to the door lock position.
(3) Install the outer cable end to the door inside handle
securely.
(4) Install the clip to the inner cable.
2. Install the inside handle rod to the door inside handle.
3. Install the door inside handle to the door.
INSPECTION
DOOR LOCK ACTUATOR CHECK
Front door

Rod positionTerminal No.Rod operation
12346
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK
LOCK
UNLOCK

Rod positionTerminal No.Rod operation
46
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK

Rod positionTerminal No.Rod operation
12346
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK
LOCK
UNLOCK

Rod positionTerminal No.Rod operationp
46
p
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK
Door inside
handle
Inner cableClip
Outer cable
end
Inside
handle rod

B Unlock
View B
Lock

View A
Unlock Lock
A

BODY -Doors42-37
Rear door

Rod positionTerminal No.Rod operationp
23
p
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK

Rod positionTerminal No.Rod operationp
23
p
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK
DOOR LOCK KEY CYLINDER SWITCH CONTINUITY
CHECK
Switch positionTerminal No.p

123123
LOCK
OFF
UNLOCK

BA

View ALock
Unlock

View B
UnlockLock